this allow to check we do not exceed the size of the SRAM as example
introduce BAREBOX_MAX_BARE_INIT_SIZE the maximum size of bare_init
this will allow your bare_init will fit in SRAM as example
ARCH can overwrite it via ARCH_BAREBOX_MAX_BARE_INIT_SIZE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have a bootm command which boots everything we can
simplify the defaultenvironment. We can call bootm on every
image type and can remove the kernelimage_type variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This switches the bootm code to the new uimage code. Also
bootm can now handle other types of images than uImages.
Currently the only architecture making use of this is
arm which allows to boot zImages, raw images and barebox
images.
I intended to make a more bisectable series from this but
I failed becuase there are many dependencies and no matter
how I tried the patches grew bigger and and bigger. So I
decided to put this all in a single patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
All handlers used to just relocate the image without any checks, so
we are doomed if we write outside of SDRAM or will overwrite ourselves.
Move the relocation up to the generic part where we have a chance
of catching these issues.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We never had interrupt support in barebox and we have no plans to
add interrupt support. Even if we do I doubt the current fragments
of irq support are helpful, so remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Linux kernel says (spi.h) :
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is
* determined by the results of previous messages and where the whole
* transaction
* ends when the chipselect goes intactive.
In other words, cs_change changes the default chipselect *behavior*.
Support of cs_change is necessary to implement the mci spi driver.
This patch also fix few things:
Passing the bus number to the brand new master device.
Disable chipselect during master->setup.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch remove those warnings in nios2 drivers:
include/io.h:7:5: warning: "__BYTE_ORDER" is not defined
include/io.h:7:21: warning: "__BIG_ENDIAN" is not defined
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds resources for the Altera TSE driver as
this driver has been moved to resources usage.
The serial device also uses resources declared with the helps
of add_generic_device.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a helper function for boards to register their memory
devices. This makes the board code smaller and also helps
getting rid of map_base and struct memory_platform_data.
And switch all of the memory to it
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
we keep struct memory_platform_data for now on we will switch off the memories
resources to struct resource
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Fix an error when bootm support is not choosen during
the configuration.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If we are using barebox on a NiosII/e variant, the
mul instruction is not supported and causes an exception.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The flush_dcache_range function takes an absolute end address
so we have to add start address to the second parameter.
Signed-off-by: Franck JULLIEN <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to match the example I'll provide on my website,
set the system frequency to 100MHz in the generic board
nios_sopc.h
Signed-off-by: Franck JULLIEN <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The device init function has the name of one of my board (comBoard).
This patch fix the name of the function to generic_device_init.
Signed-off-by: Franck JULLIEN <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds kernel_loc, kernelimage_type and bootargs to the
generic board environment. This allows the generic board
to boot linux on the example I'll provide on my website.
Signed-off-by: Franck JULLIEN <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the bootm support to the Nios2 arch.
Signed-off-by: Franck JULLIEN <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The PHY address must be passed to the driver via platform_data.
Signed-off-by: Franck JULLIEN <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
