For the phyCORE-i.MX6 add an automount command for the first partition
on the eMMC device.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable NOR for phyCORE-i.MX6 DualLite and Quad eMMC variants.
Furthermore add an extra 'status = "disabled"' in the flash node. It
has no functional effect, because the SPI bus node 'ecspi1' is disabled,
too.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some phyCORE-i.MX6 variants have eMMC instead of a NAND chip. Provide an
update_handler for them.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The extra environment folder for the phyCORE-i.MX6 had the suffix
'-mira'. That's the name of a baseboard. Since the bootloader is generic
for all baseboards, use a generic suffix for the environment folder.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Update RAM calibration values in the flashheader file for phyCORE-i.MX6
DualLite/Solo. These are verified and tested in the climatic chamber for
commercial, extended commercial, industrial and automotive i.MX6
variants.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The phyCORE-i.MX6 has either a NAND or EMMC storage device and an
external SD-Card interface. The automatic bootsource detection in the
barebox environment should reflect that.
- If the board was booted from the external SD-Card interface, it should
continue loading the kernel and device tree from it.
- If the board was booted from EMMC, it should load kernel and device
tree from the boot partition on the EMMC.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing MMC barebox environment partitions for the phyCORE-i.MX6
with EMMC. Otherwise the barebox cannot find the environment, when the
board is boot from sd-card.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Due to hardware issues the usdhc3 interface on phyBOARD-ALCOR i.MX6 and
phyBOARD-SUBRA i.MX6 doesn't work reliable at 50Mhz. You get
communication errors like
barebox@Phytec phyBOARD SUBRA:/ ls /mnt/mmc/
mmc2: detected SD card version 2.0
mmc2: registered mmc2
imx-esdhc 2198000.usdhc: timeout 2
mmc2: Cannot read MBR/partition table
Therefore reduce the maximum clock speed to avoid these problems.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyBOARD-SUBRA-i.MX6 with phyFLEX-i.MX6 Quad 1GiB on one
bank. This patch factors out the common device tree nodes for the Quad
and Solo variant into 'imx6qdl-phytec-phyboard-subra.dtsi'.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable the mmc_extcsd command to read and write MMC/eMMC registers.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
After doing a 'saveenv' command, it is no longer possible to boot.
The reason for this behaviour is that the 'barebox' partition has
currently
a size of 0x80000 (512 kB), which is not sufficient to store the barebox
binary. This causes the 'barebox' and 'barebox-environment' partitions
to overlap.
Fix this problem by increasing the size of the 'barebox' partition and
by placing the 'barebox-environment' right after it.
This patch increases the barebox partition for all i.MX boards to
0xe0000
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The LT variant has a different compatible, yet we want to run the
code on this variant aswell. Add the corresponding test.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Partition names shouldn't be continuously numbered, instead the part
behind the '@' should match the reg property. Fix this for all ARM
device trees.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
CONFIG_FITIMAGE is the variable to depend on, not
CONFIG_CMD_BOOTM_FITIMAGE which is only a wrapper option to
let CONFIG_FITIMAGE select from the bootm Kconfig menu.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes memory detection on the Digi ccxmx53 board.
Also updates dts to support nand.
Cleaned up whitespace?
Signed-off-by: Jason Cobham <cobham.jason@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The callers of get_kernel_addresses() are not interested in the
spacing after the kernel image, they are interested in the
place where they can put device tree and initrd, so pass
a pointer to mem_free to get_kernel_addresses().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Move the call to sdram_start_and_size() into get_kernel_addresses() and
remove the now unnecessary parameter mem_start.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fixes: 81737c1 mtd: Fix erasing of devices >4GiB
Several places erased a complete flash partition passing ~0 as count to
erase(). With the above commit count to erase was changed from an unsigned
type to a signed type, so the (count > f->size - offset) check in
erase() no longer triggers and the ~0 count is no longer adjusted to the whole
device size. Among other things this results in saveenv failures on NOR
flashes.
This patch fixes this by introducing an explicit macro for erasing the
whole device which is tested for in erase(). All other negative values
are rejected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Giorgio <giorgio.nicole@arcor.de>
The function we have implemented as getc has the semantics of the
standard function getchar, so rename it accorgingly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Our asprintf and vasprintf have different prototypes than the glibc
functions. This causes trouble when we want to share barebox code
with userspace code. Change the prototypes for (v)asprintf to match
the glibc prototypes. Since the current (v)asprintf are convenient
to use change the existing functions to b(v)asprintf.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Allows this code to work correct regardless of the used compiler
optimizations.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has no users and seems to be untested. Removed it.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Stefan Christ
Christian Hemp
Jan Remmet
Du Huanpeng
Jason Cobham
Teresa Remmet
Lucas Stach