README.hardware: update Beaglebone section
Updated image creation instructions. Used wic images instead of manually partitioning SD card. [YOCTO #8719] (From meta-yocto rev: aaa23941f228f08573b0e4901e8bf3fd5f1c97e3) Signed-off-by: Ed Bartosh <ed.bartosh@linux.intel.com> Signed-off-by: Ross Burton <ross.burton@intel.com> Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
This commit is contained in:
parent
924ca1037c
commit
cd271d2f2b
|
@ -160,59 +160,17 @@ this, issue the following commands from the u-boot prompt:
|
|||
To further tailor these instructions for your board, please refer to the
|
||||
documentation at http://www.beagleboard.org/bone and http://www.beagleboard.org/black
|
||||
|
||||
From a Linux system with access to the image files perform the following steps
|
||||
as root, replacing mmcblk0* with the SD card device on your machine (such as sdc
|
||||
if used via a usb card reader):
|
||||
From a Linux system with access to the image files perform the following steps:
|
||||
|
||||
1. Partition and format an SD card:
|
||||
# fdisk -lu /dev/mmcblk0
|
||||
1. Build an image. For example:
|
||||
|
||||
Disk /dev/mmcblk0: 3951 MB, 3951034368 bytes
|
||||
255 heads, 63 sectors/track, 480 cylinders, total 7716864 sectors
|
||||
Units = sectors of 1 * 512 = 512 bytes
|
||||
$ bitbake core-image-minimal
|
||||
|
||||
Device Boot Start End Blocks Id System
|
||||
/dev/mmcblk0p1 * 63 144584 72261 c Win95 FAT32 (LBA)
|
||||
/dev/mmcblk0p2 144585 465884 160650 83 Linux
|
||||
2. Use the "dd" utility to write the image to the SD card. For example:
|
||||
|
||||
# mkfs.vfat -F 16 -n "boot" /dev/mmcblk0p1
|
||||
# mke2fs -j -L "root" /dev/mmcblk0p2
|
||||
|
||||
The following assumes the SD card partitions 1 and 2 are mounted at
|
||||
/media/boot and /media/root respectively. Removing the card and reinserting
|
||||
it will do just that on most modern Linux desktop environments.
|
||||
|
||||
The files referenced below are made available after the build in
|
||||
build/tmp/deploy/images.
|
||||
|
||||
2. Install the boot loaders
|
||||
# cp MLO-beaglebone /media/boot/MLO
|
||||
# cp u-boot-beaglebone.img /media/boot/u-boot.img
|
||||
|
||||
3. Install the root filesystem
|
||||
# tar x -C /media/root -f core-image-$IMAGE_TYPE-beaglebone.tar.bz2
|
||||
|
||||
4. If using core-image-base or core-image-sato images, the SD card is ready
|
||||
and rootfs already contains the kernel, modules and device tree (DTB)
|
||||
files necessary to be booted with U-boot's default configuration, so
|
||||
skip directly to step 8.
|
||||
For core-image-minimal, proceed through next steps.
|
||||
|
||||
5. If using core-image-minimal rootfs, install the modules
|
||||
# tar x -C /media/root -f modules-beaglebone.tgz
|
||||
|
||||
6. If using core-image-minimal rootfs, install the kernel zImage into /boot
|
||||
directory of rootfs
|
||||
# cp zImage-beaglebone.bin /media/root/boot/zImage
|
||||
|
||||
7. If using core-image-minimal rootfs, also install device tree (DTB) files
|
||||
into /boot directory of rootfs
|
||||
# cp zImage-am335x-bone.dtb /media/root/boot/am335x-bone.dtb
|
||||
# cp zImage-am335x-boneblack.dtb /media/root/boot/am335x-boneblack.dtb
|
||||
|
||||
8. Unmount the SD partitions, insert the SD card into the Beaglebone, and
|
||||
boot the Beaglebone
|
||||
# dd core-image-minimal-beaglebone.wic of=/dev/sdb
|
||||
|
||||
3. Insert the SD card into the Beaglebone and boot the board.
|
||||
|
||||
Freescale MPC8315E-RDB (mpc8315e-rdb)
|
||||
=====================================
|
||||
|
|
Loading…
Reference in New Issue