Other commands implementing subcommands can reuse this code nicely.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Current u-boot top of tree builds with warnings/errors for
the following boards:
ads5121 cpci5200 mecp5200 v38b IAD210 MBX MBX860T NX823
RPXClassic debris PN62
following patch solves this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Enabling the instruction cache significantly accelerates U-Boot
operations like CRC checking, image uncompression, etc.
Kudos to Andrea Scian for pointing out.
Signed-off-by: Wolfgang Denk <wd@denx.de>
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts
provides a flexible way to create and maintain u-boot mtd
partitions. This allows commands such as "nand erase fs"
to work and the user no longer needs to decode the absolute
nand offsets. This patch enables this function for beagleboard
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Since all of the bf537-stamp and bf537-ezkit boards out there can handle it,
increase the speed of SCLK to 125MHz rather than 100MHz.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the hardware can handle it, bump the default clocks from 80mhz SCLK
and 398mhz CCLK to 100mhz SCLK and 498mhz CCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Again, don't clobber pins that we aren't actually using, and use the common
LED framework rather than our own hob-job-but-not-really-working.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that. This
will also make merging the ~10 boards I have to forward port a lot easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patches configures the NAND UPM-FSL driver with multi-chip
support for the Micron MT29F8G08FAB NAND flash memory on the
TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The SPORT_TX registers cannot be read (the hardware will trigger an error),
so drop the read helper macros.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The U-Boot UBIFS implementation is largely a direct copy from the current
Linux version (2.6.29-rc6). As already done in the UBI version we have an
"abstraction layer" to redefine or remove some OS calls (e.g. mutex_lock()
...). This makes it possible to use the original Linux code with very
little changes. And by this we can better update to later Linux versions.
I removed some of the Linux features that are not used in the U-Boot
version (e.g. garbage-collection, write support).
Signed-off-by: Stefan Roese <sr@denx.de>
CC: Artem Bityutskiy <dedekind@infradead.org>
CC: Adrian Hunter <ext-Adrian.Hunter@nokia.com>
This patch adds LZO decompression support to U-Boot. It is needed for
the upcoming UBIFS support, since UBIFS uses LZO as default compressor/
decompressor. Since we only support read-only in UBIFS, only the
decompressor is needed.
All this is copied with minor changes from the current Linux kernel
version (2.6.28-rc8).
This patch only implements this LZO decompressor support for PPC.
Other platforms using UBIFS will have to add the required
"include/asm/unaligned.h" as well. It should be fairly easy to copy this
from the Linux source tree as I have done it for PPC in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch replaces in/out8/16/32 macros by in/out_8/_be16/_be32
macros. Also volatile pointer references are replaced by the
new accessors.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix building DASA_SIM boards by increasing U-Boot's size in flash.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Detlev Zundel
Heiko Schocher
Wolfgang Denk
Nishanth Menon
Mike Frysinger
Wolfgang Grandegger
Haavard Skinnemoen
Jean-Christophe PLAGNIOL-VILLARD
Jon Smirl
Nicolas Ferre
Stefan Roese
Grzegorz Bernacki
Matthias Fuchs
Graeme Russ