Commit 8183058188 ("imx6: centralise common boot options in
mx6_common.h") broke boot on mx6sl and mx6sx by assuming that all mx6
SoCs use the same LOADADDR/SYS_TEXT_BASE range, which is not correct.
DDR on mx6sx/mx6sl starts at 0x80000000.
Adjust LOADADDR/SYS_TEXT_BASE to the proper values for mx6sx/mx6sl,
so that these SoCs can boot again.
Also, TQMA6 requires a custom CONFIG_SYS_TEXT_BASE value, so move
its setting prior to the inclusion of mx6_common.h.
Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
There are two revisions of wandboard: version B1 and C1.
Add the revision detection support, so that the correct dtb file can
be automatically loaded.
Based on the patch from Richard Hu <hakahu@gmail.com>.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
Support QEMU PIRQ routing via device tree on both i440fx and q35
platforms. With this commit, Linux booting on QEMU from U-Boot
has working ATA/SATA, USB and ethernet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The default weak version of pci_skip_dev() in drivers/pci/pci_common.c
skips the host bridge (b.d.f = 0.0.0) which is actually the i440fx/q35
chipset for QEMU targets. Define CONFIG_PCI_CONFIG_HOST_BRIDGE to make
it visible in the PCI configuration space.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable legacy IDE support on the pc target and AHCI support on the
q35 target. Default configuration is to support the pc target.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_LBA48 to support large disks. CONFIG_ATAPI is only needed
by cmd_ide.c which is not common for modern x86 targets, hence remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It turns out that QEMU x86 emulated graphic card has a built-in
option ROM which can be run perfectly with native mode by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some x86 boards set CONFIG_NR_DRAM_BANKS to 1, which causes incorrect
DRAM size printed when booting from coreboot, like this:
CPU: x86, vendor Intel, device 663h
DRAM: 636 KiB
Using default environment
Change it to 8 which should be enough for both coreboot and bare
cases, and move it to x86-common.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
netconsole had become defective over time and cleanups.
Because the feature is used very rarely nobody did take notice about this
defect.
With this patch the resulting syntax error on call will be fixed.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed
from the configs.
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
The config for pcm051 still undef'd CONFIG_USE_IRQ. This is not
needed any more since it is not defined in the whole include path
before.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
NET_RANDOM_ETHADDR depends on lib/rand.c. This patch adds dependency to
Kconfig to ensure that library is also compiled.
Remove the definitions from Blackfin boards' include/configs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This also selects CONFIG_NET for any CONFIG_CMD_NET board.
Remove the imx default for CONFIG_NET.
This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Another shell scripting command that has not been moved.
Moved using tools/moveconfig.py using these settings:
CMD_SETEXPR bool n y
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 92ac520821 (net: Remove all references to CONFIG_ETHADDR
and friends) accidentally dropped #endif. Since then, gr_ep2s60
could not build.
scripts/kconfig/conf --silentoldconfig Kconfig
CHK include/config.h
GEN include/autoconf.mk
In file included from include/config.h:5:0,
from ./include/common.h:18:
include/configs/gr_ep2s60.h:15:0: error: unterminated #ifndef
#ifndef __CONFIG_H__
^
make[1]: *** [include/autoconf.mk] Error 1
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
this removes a config entry and uses the default value
defined in config_fallbacks.h. This implements the same
behaviour as a patch series for other i.MX6 boards from
Freescale
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Since commit 92ac520821 (net: Remove all references to
CONFIG_ETHADDR and friends), the ethernet device on UniPhier boards
is not working because of the incorrect (all-zero) MAC address.
Enable CONFIG_NET_RANDOM_ETHADDR to generate the random one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
sun8i uses the same PSCI backend as sun6i, without power clamps.
Since there is no secure SRAM, the backend is placed at the end
of DRAM.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we have a PSCI backend for sun6i, enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun9i (A80) support, only uart + mmc are supported for now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A1 SRAM Base differs between sun9i and the others, update sunxi-common.h
to deal with this, so that we do not set the initial stack pointer to point
to the BROM.
This avoids the need for the weird undocumented register write I previously
took from the allwiner u-boot sources and which needed #ifdef-ery in start.S
as it needed to be done really early on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The DRAM Base differs between sun9i and the others, update sunxi-common.h to
deal with this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The latest versions of the fel tool support loading normal u-boot builds
directly, and this is now the preferred way to use the fel boot method.
This commit removes support for the old deprecated standalone fel builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Since i've been married, i also have a new surname.
Mr. Petermaier moved to Mr. Schmelzer.
In this patch i update all files in which my (old) name is present.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Switch to generic timer implementation from lib/time.c .
This also fixes a signed overflow which was in __udelay()
implementation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tyler Baker <tyler.baker@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The foundation model (FVP) emulator nominally boots using
a clean, uncompressed kernel and the "booti" command. Augment
the default U-Boot script to do this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Juno reference design typically plugs the root FS
on a USB stick. We need to wait a bit for the root to
appear so tell this on the default command line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Generic board support seems to work just fine. Tested on ml507 with
bitstream generated on the latest ISE software.
Tested-by: Georg Schardt <schardt@team-ctech.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
CONFIG_SUPPORT_EMMC_BOOT is important to enable the boot partition via
'mmc partconf 0 1 1 0' command, for example.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Adjust CONFIG_SYS_DFU_DATA_BUF_SIZE in order to avoid the following error
when running the dfu command:
=> dfu 0 mmc 0
dfu_get_buf: Could not memalign 0x2000000 bytes
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The ARM Trusted Firmware or other security solutions are
eating memory from the top of the physical SDRAM1 space,
moving backward from 0xffffffff, currently occupying e.g.
0xfe000000-0xffffffff with Trusted Firmware.
This solution to reserving memory for secure world is not
optimal, so we need to think of how the secure world and
earlier boot stages should communicate to U-Boot what
memory they are eating up. For now let's just put 16MB
aside.
Also enable the memory test command and define start and
end of the test range so we can check that we actually have
all that memory available and working.
Suggested-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing on the ARM Versatile Express Juno board showed intermittent CFI
flash detection problems.
Debug output in exception cases showed that the NOR flash was returning
incorrect values to a query command:
fwc addr 0000000008000000 cmd f0 f0f0f0f0 32bit x 8 bit
fwc addr 0000000008000000 cmd ff ffffffff 32bit x 8 bit
fwc addr 0000000008000154 cmd 98 98989898 32bit x 8 bit
is= cmd 51(Q) addr 0000000008000040 is= 00800051 51515151
fwc addr 0000000008001554 cmd 98 98989898 32bit x 8 bit
is= cmd 51(Q) addr 0000000008000040 is= 00800051 51515151
fwc addr 0000000008000000 cmd f0 00f000f0 32bit x 16 bit
fwc addr 0000000008000000 cmd ff 00ff00ff 32bit x 16 bit
fwc addr 0000000008000154 cmd 98 00980098 32bit x 16 bit
is= cmd 51(Q) addr 0000000008000040 is= 00800051 00510051
fwc addr 0000000008001554 cmd 98 00980098 32bit x 16 bit
is= cmd 51(Q) addr 0000000008000040 is= 00800051 00510051
Debugging showed that the problem could be solved by preventing u-boot
from scanning different flash widths by specifying
CONFIG_SYS_FLASH_CFI_WIDTH so that only using the 'correct' width was
used.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Move CONFIG_CMD_CACHE to mx6_common and standardise the way it's defined.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini at konsulko.com>
Move generic miscellaneous options that are standard across most, if not all,
mx6 boards to central mx6_common define to ensure consistent features.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
All boards define CONFIG_MX6, CONFIG_DISPLAY_BOARDINFO, CONFIG_DISPLAY_CPUINFO
and CONFIG_SYS_GENERIC_BOARD so define them in mx6_common
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini at konsulko.com>
The linux/sizes.h, asm/arch/imx-regs.h, asm/imx-common/gpio.h,
config_cmd_default.h includes are used fairly universally across imx6 boards
so include them in mx6_common.h by default.
We define CONFIG_SYS_NO_FLASH before config_cmd_default.h so that we
don't have to undef CONFIG_CMD_FLASH / CONFIG_CMD_IMLS everywhere.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Standardise mx6_common.h to the same as other mx6 boards
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Tom Rini <trini at konsulko.com>
Don't use error-prone arch timer code and instead use system
timer implementation to simplify our code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.
Signed-off-by: Stefan Agner <stefan@agner.ch>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently we need to build one U-boot image for each of the wandboard
variants: quad, dual-lite and solo.
By switching to SPL we can support all these variants with a single binary,
which is very convenient.
Based on the work from Richard Hu.
Tested kernel booting on the three boards.
Signed-off-by: Richard Hu <hakahu@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Enable some additional ENV commands in sandbox to aid in build testing
and run testing.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ccsr_ddr structure is already defined in fsl_immap.h. Remove
this duplicated define. Move fixed timing into ls1021atwr.h.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
The original load address of U-Boot is 0x67f80000. The address
space of NOR flash is 0x60000000 to 0x67ffffff. It will cause
the size of u-boot couldn't be larger than 512K. As more features
are supported in u-boot, the size of u-boot is larger than 512K.
To fix this issue, the load address of U-Boot for NOR boot is
adjusted to 0x60100000.
In RCW, the PBI command needs to change as follows:
.pbi
-write 0xee0200, 0x67f80000
+write 0xee0200, 0x60100000
.end
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove the calls to net_random_ethaddr() that some boards and some
drivers are calling. This is now implemented inside of net/eth.c
Enable the feature for all boards that previously enabled it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-By: Michael Walle <michael@walle.cc> (for the lsxl board part)
Series-changes: 2
-Fixed bfin build errors
We really don't want boards defining fixed MAC addresses in their config
so we just remove the option to set it in a fixed way. If you must have
a MAC address that was not provisioned, then use the random MAC address
functionality.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sunxi platforms use ARM Cortex A8, A7 and A15 (unsupported yet) CPU cores,
which all have 64 bytes cache line size.
This is required to e.g. enable USB gadget.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for UART2 (2-pin version but note that RTS/CTS pins are available
pn that port for possible future use), can be selected in config
by using CONFIG_CONS_INDEX=3
Signed-off-by: Laurent Itti <laurentitti@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On my A10 OlinuxIno Lime I noticed a huge (5+ seconds) delay coming from
console_init_r. This turns out to be caused by the preconsole buffer flushing
to the cfb_console. The Lime only has a 16 bit memory bus and that is already
heavy used to scan out the 1920x1080 framebuffer.
The problem is that print_pre_console_buffer() was printing the buffer once
character at a time and the cfb_console code then ends up doing a cache-flush
for touched display lines for each character.
This commit fixes this by first building a 0 terminated buffer and then
printing it in one puts() call, avoiding unnecessary cache flushes.
This changes the time for the flush from 5+ seconds to not noticable.
The downside of this approach is that the pre-console buffer needs to fit
on the stack, this is not that much to ask since we are talking about plain
text here. This commit also adjusts the sunxi CONFIG_PRE_CON_BUF_SZ to
actually fit on the stack. Sunxi currently is the only user of the pre-console
code so no other boards need to be adjusted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bootscripts for some distro's such as Android can benefit from knowing
what boot media its script was loaded from.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since there is a default CONFIG_SYS_PBSIZE definition in config_fallbacks.h,
this setting is no longer required in board configurations.
Signed-off-by: Soeren Moch <smoch@web.de>
Only enable graphical output for stdout/stderr (and a usb keyboard for stdin)
when a hdmi device is detected.
Serial console is always enabled for stdin/stdout/stderr.
Signed-off-by: Soeren Moch <smoch@web.de>
Add support for USB OTG host mode. Only high speed devices supported so far
(e.g. usb 2.0 hub required to connect a keyboard).
Signed-off-by: Soeren Moch <smoch@web.de>
Hummingboard dual, dual-lite and solo are now supported via SPL mechanism.
Remove the previous hummingboard support, which does not use SPL and supported
only the solo variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Starting USB initialization is useful for those who use Cuboxi/Hummingboard
with HDMI and USB keyboard.
However, when booting without a HDMI connection we can skip the usb
initialization, which makes the boot faster.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
This patch fixes the USB EHCI support on the TQMa6 SoM. Additionally
some filesystems are added, included the generic FS commands (e.g.
ls...).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-By: Markus Niebel <Markus.Niebel@tq-group.com>
There are users of Cuboxi and Hummingboard that use these boards without
connecting them to a USB/serial adapter.
Allow such usage by allowing the HDMI port to act as stdout and USB keyboard
as stdin.
The serial console still also works as stdin/stdout.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
Add HDMI output using PLL5 as the source for the IPU clocks,
and accurate VESA timings.
These settings are based on the patch from Soeren Moch <smoch@web.de>
submitted for the tbs2910 mx6 based board.
It allows the display to work properly at 1024x768@60.
This should make the hdmi output signal compatible with most if not all
modern displays.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
This change enables the configs required to init and setup max77686
regulator driver, using the new driver model pmic and regulator API.
And also changes the old pmic framework calls to the new ones.
This commits enables:
- CONFIG_ERRNO_STR
- CONFIG_DM_PMIC
- CONFIG_DM_PMIC_CMD
- CONFIG_DM_PMIC_MAX77686
- CONFIG_DM_REGULATOR
- CONFIG_DM_REGULATOR_CMD
- CONFIG_DM_REGULATOR_MAX77686
And removes the unused:
- CONFIG_DM_I2C_COMPAT
- CONFIG_POWER
- CONFIG_POWER_I2C
- CONFIG_POWER_MAX77686
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This config name was never used, because the present pmic command
was precompiled for the CONFIG_POWER.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move the configs listed below from exynos5-dt-common.h to exynos5-common.h:
- CONFIG_POWER
- CONFIG_POWER_I2C
fixes build break for Arndale and Smdk5250 boards.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that the ohci code supports usb interrupt queues we can switch (back)
to using an usb interrupt queue for usb-kbd interrupt polling. This
greatly reduces u-boot's latency when dealing with usb keyboards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Bhuvanchandra DV
Fabio Estevam
Fabio Estevam
Gabriel Huau
Bin Meng
Hannes Schmelzer
Lars Poeschel
Tom Rini
Michal Simek
Joe Hershberger
Masahiro Yamada
Markus Niebel
Chen-Yu Tsai
Daniel Kochmański
Hans de Goede
Hannes Schmelzer
Marek Vasut
Linus Walleij
Ricardo Ribalda
Ryan Harkin
Peter Robinson
Tim Harvey
Heiko Schocher
Stefan Agner
York Sun
Alison Wang
Paul Kocialkowski
Laurent Itti
Nikolay Dimitrov
Soeren Moch
Stefan Roese
Przemyslaw Marczak