Commit graph

28 commits

Author SHA1 Message Date
Karicheri, Muralidharan
d57dee5787 serial: nsl16550: add hw flow control support
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
2014-05-12 15:19:45 -04:00
Vitaly Andrianov
ef509b9063 k2hk: add support for k2hk SOC and EVM
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.

This patch add support for keystone architecture and k2hk evm.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
2014-04-17 17:24:38 -04:00
Tom Rini
456ccfdf0d TI:omap3: Drop omap3_zoom2
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.

Signed-off-by: Tom Rini <trini@ti.com>
2014-01-07 16:41:12 -05:00
TENART Antoine
9ed6e41239 Prepare for TI816X : reuse existing code from TI814X
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX

Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:37 -04:00
Lokesh Vutla
571804086f ARM: AM43xx: Add build support
Add AM43xx support in the required places

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Tom Rini
7f5eef93af arm: Remove OMAP2420H4 and all omap24xx support
The omap2420H4 was the only mainline omap24xx board.  Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time.  Remove this board as there's not been interest in
it in U-Boot for quite a long time.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:19 -04:00
Manfred Huber
fd2aeac560 omap3_beagle: Flush UART3 xmit on enable if TEMT is broken
Flush UART3 xmit on enable if TEMT is broken

On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.

Signed-off-by: Manfred Huber <man.huber@arcor.de>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-04-08 11:29:05 -04:00
Matt Porter
6213a68fe8 ns16550: enable quirks for ti814x
TI814X requires the same quirks as AM33XX to be enabled.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-03-24 12:49:12 -04:00
Simon Glass
69e0683241 serial: ns16550: Remove unwanted cast
This cast does not seem correct, since we should be writing to a pointer,
not a ulong.

This fixes the following warning on nds32:

-ns16550.c:49: warning: passing argument 2 of 'writeb' makes pointer from integer without a cast

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-15 16:14:01 -04:00
Javier Martinez Canillas
7de0fe1ac3 serial/ns16550: add an option to avoid hanging on broken platforms
Some platforms (e.g. IGEPv2 board) has a broken ns16550 UART that
does not set the TEMT bit when the transmitter is empty in SPL.
This makes U-Boot to hang while waiting for TEMT to be set.

Add a new option to avoid this:

CONFIG_SYS_NS16550_BROKEN_TEMT

16550 UART set the Transmitter Empty (TEMT) Bit when all output
has finished and the transmitter is totally empty. U-Boot waits
for this bit to be set to initialize the serial console. On some
broken platforms this bit is not set in SPL making U-Boot to
hang while waiting for TEMT. Define this option to avoid it.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
2013-01-10 15:09:24 -07:00
Scott Wood
cb55b33200 serial/ns16550: wait for TEMT before initializing
TEMT is set when the transmitter is totally empty and all output has
finished.

This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.

Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
2012-11-26 15:41:20 -06:00
Marek Vasut
f2041388bd serial: ns16550: Call usbtty_poll only in non-SPL build
Having both USBTTY and CONFIG_SERIAL_MULTI enabled in SPL, the
usbtty.c file is protected in Makefile to not be compiled into
the SPL. Yet, the ns16550 serial driver does not contain such
protection. Add it to avoid missing symbol error.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
2012-10-15 11:53:58 -07:00
Mikhail Kshevetskiy
99b603e714 serial/ns16550: ns16550 has a different register layout on SOC_DA8XX
also fix NS16550_init() as we need 16x divider

Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
2012-09-01 14:58:10 +02:00
Chandan Nath
5289e83a8c ARM:AM33XX: Add support for TI AM335X EVM
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:36 +02:00
Simon Glass
f8df9d0d1a NS16550: trivial code clean for checkpatch
This removes most checkpatch warnings from the ns16550 driver and its
header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-23 20:19:53 +02:00
Dave Aldridge
79df1208ee ns16550: change to allow 32 bit access to registers
If CONFIG_SYS_NS16550_MEM32 is defined then 32 bit memory
mapped access will be used to read/write the uart registers.

This is especially useful for SoC devices that implement 16550
compatible uarts but that have peripheral access width constraints.

Signed-off-by: Dave Aldridge <fovsoft@gmail.com>
2011-10-01 21:54:16 +02:00
Prafulla Wadaskar
a160ea0b5e Serial: ns16550: Add support for CONFIG_SYS_NS16550_IER macro
On some processors this ier register configuration is different
for ex. Marvell Armada100

This patch introduce CONFIG_SYS_NS16550_IER macro support to
unconditionally initialize this register.

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2010-12-16 23:02:51 +01:00
Stefan Roese
1a2d9b30e3 ns16550: Add WATCHDOG_RESET to putc for short watchdog timeout boards
Call watchdog_reset() upon newline. This is done here in putc
since the environment code uses a single puts() to print the complete
envrironment upon "printenv". So we can't put this watchdog call
in puts().

This is needed for boards with a very short watchdog timeout, like the
lwmon5 with a 100ms timeout. Without this patch this board resets in the
commands with long outputs, like "printenv" or "fdt print".

Note that the image size is not increased with this patch when
CONFIG_HW_WATCHDOG or CONFIG_WATCHDOG are not defined since the compiler
optimizes this additional code away.

Signed-off-by: Stefan Roese <sr@denx.de>

Fix typo in comment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-13 21:59:31 +02:00
Graeme Russ
167cdad137 SERIAL: Enable port-mapped access
The x86 architecture exclusively uses Port-Mapped I/O (inb/outb) to access
the 16550 UARTs. This patch mimics how Linux selects between Memory-Mapped
and Port-Mapped I/O. This allows x86 boards to use CONFIG_SERIAL_MUTLI and
drop the custom serial port driver

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06 00:16:28 +02:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Ladislav Michl
a1b322a983 ns16550: kick watchdog while waiting for a character
ns16550 busyloops waiting for incoming byte causing watchdog to reboot
while waiting for a key press. A call to WATCHDOG_RESET in NS16550_getc
loop fixes it.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2010-02-03 22:46:58 +01:00
Tom Rix
660888b7fb ZOOM2 Add serial support.
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS.  On your host pick the first
enumeration.

The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.

The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.

The kernel bootargs are
console=ttyS3,115200n8

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
2009-06-12 20:39:53 +02:00
Detlev Zundel
200779e3e2 Rename common ns16550 constants with UART_ prefix to prevent conflicts
Fix problems introduced in commit
7b5611cdd1 [inka4x0: Add hardware
diagnosis functions for inka4x0] which redefined MSR_RI which is
already used on PowerPC systems.

Also eliminate redundant definitions in ps2mult.h.  More cleanup will
be needed for other redundant occurrences though.

Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-04-03 22:34:07 +02:00
Mike Frysinger
b4746d8bf9 drivers/serial/ns16550: move ifdef into Makefile COBJS-$(...)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-21 22:49:53 +01:00
Ron Madrid
f5675aa5ce Create configuration option for restricted ns16550 functions
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error.  This option will exclude all functions with exception of
NS16550_putc and NS16550_init.  This will be used primarily to save space and
remove unused code from builds in which space is limited.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
2009-02-19 00:34:51 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Wolfgang Denk
7ec8bb15ee OMAP5912: fix FIFO handling in UART driver
According to the OMAP5912 Serial Interfaces Reference Guide (see
http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the
FIFO_EN enable bit in the FIFO Control Register (FCR) can only be
changed when the baud clock is not running, i. e. when both DLL and
DLH are set to 0.

Thus make sure that DLL and DLH are 0 when writing the FCR.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-02-05 00:04:15 +01:00
Jean-Christophe PLAGNIOL-VILLARD
1378df792a drivers/serial : move serial drivers to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25 23:24:16 +01:00
Renamed from drivers/ns16550.c (Browse further)