Current code does not set gpio output value in ich6_gpio_direction_output(),
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
The ich spi controller driver spi_xfer() tries to align reading
address to 64 bytes when doing spi data in, which causes a bug of
either infinite loop or a huge size memcpy().
Actually the ich spi controller does not have such requirement of
64 bytes alignment when reading data from spi slave devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Earlier commit 73a1cb27 mistakenly used CONFIG_SYS_TIMER_CLK_FREQ.
It should be CONFIG_TIMER_CLK_FREQ.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
[York Sun: This is the difference between two patch versions]
Reviewed-by: York Sun <yorksun@freescale.com>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.
This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.
The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
Sync this up with Linux v3.18-rc5. Exclude features that are unlikely to
supported in U-Boot soon (regulators, pinmux). Also the addresses are
updated to 32-bit. Otherwise it is the same. Also bring in the dt-bindings
for pinctrl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
This will be used by nyan-big, but bring it in in a separate patch since it
will be common to other boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
There seem to be a few EEPROM drivers around - perhaps we should have a
single standard one? This simple driver is used for sandbox testing, but
could be pressed into more active service.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add an I2C bus to the device tree, with an EEPROM emulator attached to one
of the addresses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enable the options to bring up I2C on sandbox. Also enable all the available
I2C commands for testing purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
To enable testing of I2C, add a simple I2C EEPROM simulator for sandbox.
It supports reading and writing from a small data store.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This driver includes some test features such as only supporting certain
bus speeds. It passes its I2C traffic through to an emulator.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In order to test I2C we need some sort of emulation interface. Add hooks
to allow a driver to emulate an I2C device for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The concept of a 'current bus' is now implemented in the command line
rather than in the uclass. Also the address length does not need to
be specified with each command - really we should consider dropping
this from most commands but it works OK for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The uclass implements the same operations as the current I2C framework but
makes some changes to make it fit driver model better:
- Remove the chip address from API calls
- Remove the address length from API calls
- Remove concept of 'current' I2C bus
- Drop all existing init functions
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The functions error's numbers are standarized - but the error
messages are not.
The errors are often handled with unclear error messages,
so why not use an errno standarized messages.
Advantages:
- This could decrease the binary size.
- Appended with a detailed information,
the error message will be clear.
This commit introduces new function:
- const char *errno_to_str(int errno)
The functions returns a pointer to the errno corresponding text message:
- if errno is null or positive number - a pointer to "Success" message
- if errno is negative - a pointer to errno related message
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Tom Rini <trini@ti.com>
Adjust the configuration to use the driver model version of the pl01x
serial driver. Add the required platform data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The private data size is missing from the driver, so we store it at 0,
which causes problems when something overwrites memory at 0.
Fix this.
Change-Id: I6f551ee905b0064ae8343e41e46450c37c8c8c1a
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Move strlcpy() definition from drivers/usb/gadget/ether.c to
lib/string.c because it is a very useful function.
Let's add the prototype to include/linux/string.h too.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
As NOR/NAND/SD boot are all supported on LS1021AQDS/TWR
boards, the prompt message "Support ls1021aqds_nor" in
Kconfig is not clear. This patch changes it to
"Support ls1021aqds".
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
'eccstat' array elements might be used uninitialized
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define the board specific smp_set_cpu_boot_addr() function to set
the start address for secondary cores in the LS1021A specific manner.
Define the board specific smp_kick_all_cpus() functioin to boot a
secondary core. Here the BRR contains control bits for enabling boot
for each core. On exiting HRESET or PORESET, the RCW BOOT_HO field
optionally allows for logical core 0 to be released for booting or to
remain in boot holdoff. All other cores remain in boot holdoff until
their corresponding bit is set.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For some SoCs, the system clock frequency may not equal to the
ARCH Timer's frequency.
This patch uses the CONFIG_TIMER_CLK_FREQ instead of
CONFIG_SYS_CLK_FREQ, then the system clock macro and arch timer
macor could be set separately and without interfering each other.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For some SoCs, the pen address register maybe in BE mode and the
CPUs are in LE mode.
This patch adds BE mode support for smp pen address.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Freescale LS1021AQDS share some pins, so Add the hwconfig option
that allows the user to choose which the function he wants.
The main pin mux IP is:
eSDHC, SAI, IIC2, RGMII, CAN, SAI.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD/NAND/QSPI boot definations are wrong for QE support, this
patch is to fix this error.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch will fix the bug that the partitions on the SD card could
not be accessed and add the support for the FAT fs.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add SUPPORT_SPL feature for SD and NAND boot on
LS1021AQDS and LS1021ATWR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On LS1, DDR is initialized by reading SPD through I2C interface
in SPL code. For I2C, ll_entry_count() is called, and it returns
the number of elements of a linker-generated array placed into
subsection of .u_boot_list section specified by _list argument.
So add I2C linker list in the generic .lds to fix the issue about
using I2C in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In SD boot, the magic number of u-boot image will be checked.
For LS102xA, u-boot.bin doesn't have the magic number. So use
u-boot.img which includes the magic number instead of u-boot.bin
when producing u-boot-with-spl-pbl.bin.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For LS102xA, the size of spl/u-boot-spl.bin is variable.
This patch adds the support to deal with the variable
u-boot size in pblimage tool. It will be padded to 64
byte boundary.
Use pblimage_check_params() to add the specific operations
for ARM, such as PBI CRC and END command and the calculation
of pbl_cmd_initaddr.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Axel Lin
Bin Meng
Tom Rini
Xiubo Li
Simon Glass
Allen Martin
Przemyslaw Marczak
Masahiro Yamada
Alison Wang
Jaiprakash Singh
Tang Yuantian
Nikhil Badola
Yao Yuan
Chenhui Zhao