Commit graph

35 commits

Author SHA1 Message Date
Fabio Estevam
4e8b7544b7 rtc: Make mc13783-rtc driver generic
Rename mc13783-rtc so that it can be used for both MC13783 and MC13892 PMICs.

efikamx board, for example, does use a MC13892 PMIC, but the RTC selection is currently made as:

#define CONFIG_RTC_MC13783

,which is not very obvious.

Let the MC13783 and MC13892 RTC be selected by:

#define CONFIG_RTC_MC13XXX

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-11-03 22:56:19 +01:00
Fabio Estevam
8a508e303e qong: remove unneeded "1" from qong.h
Remove unneeded "1" from qong.h.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2011-11-03 22:56:18 +01:00
Wolfgang Denk
87a5d60103 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-28 00:15:19 +02:00
Helmut Raiger
9660e442de cosmetic: s/BOARD_LATE_INIT/CONFIG_BOARD_LATE_INIT
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover

 #define BOARD_LATE_INIT		1

and adds some basic documentation for board specific
callbacks in README.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-10-27 23:53:59 +02:00
Stefano Babic
f33bd087c6 MX3: qong: use new pmic driver
Switch to new pmic generic driver.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-10-27 21:56:31 +02:00
Helmut Raiger
62a22dca32 video: Moving mx3fb.c to CONFIG_VIDEO
mx3fb.c was based on CONFIG_LCD and is moved by this patch to
CONFIG_VIDEO, which has greater freedom in selecting videomodes
even at runtime.

This renders the accumulating list of display defines
(CONFIG_DISPLAY_VBEST..., CONFIG_DISPLAY_C057...) obsolete as
these may be setup through env variables:

uboot> setenv mydisplay 'video=ctfb240,y:320,depth:16,mode:0,pclk:185925,
	le:9,ri:17,up:7,lo:10,hs:1,vs:1,sync:100663296,vmode:0'
uboot> setenv videomode ${mydisplay}

This commit also fixes the board config files for qong and
imx31_phycore boards as needed. The videomode settings of
previously supported displays are added to CONFIG_EXTRA_ENV_SETTINGS
now. CONFIG_SYS_MALLOC_LEN for imx31_phycore board is increased
to make the frame buffer allocation working with the changed
driver.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2011-10-13 10:41:36 +02:00
Mike Frysinger
31a4f1e5b6 board configs: drop NET_MULTI references
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it.  So scrub all references to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Stefano Babic
22a9ea974b MX31: QONG: drop config.mk
Remove obsolete config.mk from QONG board.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-06-21 22:26:21 +02:00
Michael Jones
2cc195e0a5 Remove remnants of obsolete CONFIG_SYS_GBL_DATA_SIZE comments
commit 25ddd1fb0a left remnants of
many comments about CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
2011-05-12 23:04:55 +02:00
Stefano Babic
8627111543 IMX: MX31: Cleanup include files and drop nasty #ifdef in drivers
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:05 +02:00
Stefano Babic
8640c98463 MX31: qong: add watchdog
Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-04-27 19:38:04 +02:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Wolfgang Denk
553f09823c Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZE
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE

No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.

Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken.  Last known maintainers on Cc:

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:03:25 +02:00
Wolfgang Denk
b952c24ade QONG: fix and update board config file
Fix flash memory map and other updates for QONG board:

- adjust/fix "kernel_addr" settings
- adjust/fix mtdparts NOR flash settings
- add mtdparts NAND flash mapping
- sort command list
- enable "setexpr" command
- enable ext2 support
- delete bogus comment

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2010-10-19 12:55:16 +02:00
Wolfgang Denk
6ca803750e Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-10-17 19:57:38 +02:00
Stefano Babic
d7dc464be4 MX31: Add USB Host support to the QONG board
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-13 18:11:55 +02:00
Stefano Babic
b9eb3fdf2f MX31: Add support to update FPGA bitstream
The patch adds the possibility to update the QONG
FPGA (a Lattice XP2-5E) with u-boot using some GPIOs
to drive the JTAG interface.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-10-13 18:10:56 +02:00
Ben Gardiner
11080ab66d ARM: relocation: don't undef CONFIG_SYS_ARM_WITHOUT_RELOC
There were some #undef's of CONFIG_SYS_ARM_WITHOUT_RELOC added to a few board
configs as part of the arm relocation series; but these are not needed now as we
do not #undef what is not #defined in the first place.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Heiko Schocher <hs@denx.de>
2010-10-13 09:57:47 +02:00
Heiko Schocher
a784c01adc ARM: relocation: fix typo in comment
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-10-13 09:50:55 +02:00
Stefano Babic
9f481e95ba MXC: Correct SPI_CPOL setting in SPI driver
The handling of the SPI_CPOL bit inside the SPI
driver was wrong. As reported by the manual,
the meaning of the SSPOL inside the
configuration register is the same as reported
by SPI specification (0 if low in idle, 1 is high
on idle). The driver inverts this logic.

Because this patch sets the logic as specified, it is required
to clear the CPOL bit in the configuration file to adapt
to the correct logic.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: David Jander <david.jander@protonic.nl>
2010-09-30 14:42:13 +02:00
Stefano Babic
c4ea142424 Use common function to set GPIOs for MX3 and MX5
The patch adds support for setting gpios to the
MX51 processor and change name to the corresponding
functions for MX31. In this way, it is possible to get rid
of nasty #ifdef switches related to the processor type.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-29 11:24:30 +02:00
Heiko Schocher
e48b7c0aad ARM: implement relocation for ARM11
Change the implementation for ARM11 to relocate the code to an
arbitrary address in RAM.

Tested on the qong board.

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19 19:29:53 +02:00
Heiko Schocher
7e4a9e6dc8 ARM (ARM11): add data cache support, test on Qong board
Add data cache support for arm1136 systems.

Enable "cache" command on Qong board and test performance.

    Test 1: Loading 127 MB of data from NAND flash into RAM:

    Instr. Cache	off	on	on
      Data Cache	off	off	on
    --------------------------------------------------
    QONG (ARM11)	177s	95s	43s	= x 4.1

    Test 2: uncompressing a gzipped image from RAM to RAM
            (size compressed: 6.5 MiB, uncompressed: 35 MiB):

    Instr. Cache	off	on	on
      Data Cache	off	off	on
    --------------------------------------------------
    QONG (ARM11)	1.54s	0.95s	0.18s	= x 8.6

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19 19:29:51 +02:00
Stefano Babic
03af5abd85 MX31: Added support for the Casio COM57H5M10XRC to QONG
The patch adds setup to connect a CASIO COM57H5M10XRC
(640x480 TFT display) to the QONG module.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-19 09:15:50 +02:00
Stefano Babic
e98ecd7110 MX31: Add support for PMIC to the QONG module
Add support for the PMIC (MC13783) controller
and enables charging of the RTC battery.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Wolfgang Denk
900a1fe8c8 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-05-04 22:49:15 +02:00
Stefano Babic
c9d944d35e MX31: Add UBI support to QONG module
The UBI/UBIFS support is added to the QONG module.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:26 -05:00
Stefano Babic
45997e0a86 MX31: Add support for NAND to QONG board
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Wolfgang Denk
8a1cdaa9d5 QONG: Adapt flash addresses and mtdparts to grown image size
Also enable HUSH shell.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-04-28 12:54:43 +02:00
Stefano Babic
7c8cf0d0c7 MX31: Added LCD support for QONG module
Added support for LCD and splash image to the QONG module.
The supported display is VBEST-VGG322403.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-27 23:13:37 +02:00
Ilya Yanok
47d19da4d3 serial_mx31: allow it to work with mx27 too and rename to serial_mxc
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-06-21 16:18:13 +02:00
Stefan Roese
942556a92a mtd: MTD related config header changes (mtdparts command)
By changing the cmd_mtdparts to only use the MTD infrastructure and
not the direct interface to the CFI NOR FLASH driver we now need
to add the MTD infrastructure to all boards using those mtdparts
commands. This patch adds those components:

CONFIG_MTD_DEVICE (for all FLASH types)

plus

CONFIG_FLASH_CFI_MTD (for NOR FLASH)

To all board maintainers: Please test this on your platforms and
report any problems/issues found. Thanks.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Martin Krause <martin.krause@tqs.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
2009-06-12 20:45:47 +02:00
Stefan Roese
68d7d65100 Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-03-20 22:39:14 +01:00
Ilya Yanok
b4e85d0f37 qong: changes to Dave/DENX Qong configuration
1. Changes to the default environment:
  - "bootcmd" defined as "run flash_self"
  - "saveenv" command removed from "update"
  - "uboot" changed to "u-boot" (also in "load")
  - "addmtd" variable defined (and added to all boot commands)
2. CONFIG_CMD_JFFS2 defined to enable "mtdparts" command
3. MTDIDS_DEFAULT and MTDPARTS_DEFAULT defined
4. CONFIG_SYS_CBSIZE changed from 256 to 512. That solves the problem
with truncated "bootargs" environment variable.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
2009-02-18 04:24:35 +01:00
Ilya Yanok
0d19f6c8cb qong: support for Dave/DENX QongEVB-LITE board
This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-10 00:22:31 +01:00