Commit graph

61 commits

Author SHA1 Message Date
SRICHARAN R
5e9cd44ca0 ARM: OMAP4/5: Move USB clocks to essential group.
USB clocks will be required for fastboot, tftp
related functionalities. Move these clocks to
essential group inorder to have the functionality
working when non-essential clocks are not enabled.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:36 +02:00
SRICHARAN R
dbf8fb6ad1 ARM: OMAP4/5: Move gpmc clocks to essential group.
GPMC clocks are currently getting enabled as a part
non-essential clocks. This will be required during
NOR boot. Move this to essential group to keep the
functionality, when non-essential clocks are not
enabled.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:36 +02:00
SRICHARAN R
254763822e ARM: OMAP4+: Move external phy initialisations to arch specific place.
The external phy is present in the case OMAP5 soc is currently
configured in emif-common.c. This results in having dummy structures
for those Socs which do not have a external phy. So by having a weak
function in emif-common and overriding it in OMAP5, avoids the use
of dummy structures.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:35 +02:00
Sebastien Jan
cc009defa4 omap4: Use a smaller M,N couple for IVA DPLL
This reduced M,N couple corresponds to the advised value from
TI HW team.

Tested on 4460 Pandaboard, it also provides peripheral clocks
closer to the advised values.

Signed-off-by: Sebastien Jan <s-jan@ti.com>
2012-07-07 14:07:35 +02:00
Lokesh Vutla
784ab7c545 OMAP5: EMIF: Add support for DDR3 device
In OMAP5432 EMIF controlller supports DDR3 device.
This patch adds support for ddr3 device intialization and configuration.
Initialization sequence is done as specified in JEDEC specs.
This also adds support for ddr3 leveling.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07 14:07:24 +02:00
Lokesh Vutla
43037d7631 OMAP5: ADD precalculated timings for ddr3
Adding precalculated timings for ddr3 with 1cs
adding required registers for ddr3

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-07-07 14:07:23 +02:00
Tero Kristo
2d622b03f8 omap4: do not enable auxiliary cores
Booting up these cores (dsp / ivahd / cortex-m3) is bad without
firmware running on them, and they will hang preventing any kind
of sleep transitions later on with the kernel.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:41 +02:00
Tero Kristo
71ee921de0 omap4: do not enable fs-usb module
If this is done in the bootloader, the FS-USB will later be stuck into
intransition state, which will prevent the device from entering idle.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
2012-05-15 08:31:41 +02:00
Simon Glass
a35925b8c1 Add abs() macro to return absolute value
This macro is generally useful to make it available in common.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-05-15 08:31:37 +02:00
SRICHARAN R
002a2c0c66 OMAP4/5: Make the sysctrl structure common
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:24 +02:00
SRICHARAN R
087189fb54 OMAP4/5: Make the silicon revision variable common.
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:24 +02:00
SRICHARAN R
8de17f4617 OMAP5: palmas: Configure nominal opp vdd values
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.

Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
	http://lists.denx.de/pipermail/u-boot/2012-March/119151.html

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
SRICHARAN R
f40107345c OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-05-15 08:31:23 +02:00
Nishanth Menon
f2ae6c1a83 OMAP4: scale voltage of core before MPU scales
OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.

As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Nishanth Menon
3acb553439 OMAP4460: TPS Ensure SET1 is selected after voltage configuration
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Nishanth Menon
a78274b205 OMAP3+: Introduce generic logic for OMAP voltage controller
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.

With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.

NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Aneesh V
c8ff6a9ed9 OMAP4460: Reduce MPU clock speed from 920 to 700
We do not have thermal management or Smartreflex
enabled at U-Boot level. So, it's better to stick
to OPP100 for MPU instead of the OPP Turbo that is
used now. Adjust the VDD_MPU accordingly.

Tested-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
2012-02-12 10:11:32 +01:00
Govindraj.R
95f8791042 OMAP3+: Clock: Adding ehci clock enabling
Adding ehci clock enabling mechanism part of clock framework.
When essential clocks are enabled during init phase usb host
clocks can also be enabled from clock framework.

Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-02-12 10:11:31 +01:00
Aneesh V
fe7104b307 omap4: fix boot issue on ES2.0 Panda
Fix boot issue on ES2.0 Panda by tuning some
IO settings. The CONTROL_EFUSE_2 register has
to be over-ridden in software for 4430 boards.

Commit 23e9f0723e
wrongly did this for CONTROL_EFUSE_1. Reverting
this and doing it for CONTROL_EFUSE_2.

Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Raúl Porcel <armin76@gentoo.org>
2012-01-16 08:40:11 +01:00
Aneesh V
23e9f0723e omap4: fix IO setting
The value from TRIM is not working for some 4430 silicons.
So, override with hw team recommended value. However, for
4460 TRIM value shall be used as long as the part is trimmed

This fixes boot problem on some OMAP4430 ES2.0 Panda boards
out there.

Cc: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Aneesh V
9404758e9b omap4460: add ES1.1 identification
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Sricharan
78f455c055 omap4/5: Add support for booting with CH.
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
bb772a5944 omap5: emif: Add emif/ddr configurations required for omap5 evm
Add the emif configurations required for omap5 soc.Add the
correct ddr part configurations required for omap5 evm board.
EDB8164B3PH from ELPIDA is the part used on the board.

Also changes are done to retain some part of the code
common for OMAP4/5 and keep only the remaining in the Soc
specific directories.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
2e5ba48928 omap5: clocks: Add clocks support for omap5 platform.
Adding the correct configurations required for
dplls, clocks, for omap5 Soc.

Also changes are done to retain some part of the code common
for OMAP4/5 and move only the remaining to the Soc specific
directories.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
ce170beeb7 omap4: make omap4 code common for future reuse
Much of omap4 soc support code can be reused for omap5.
Move them to the omap-common directory to facilitate
this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Wolfgang Denk
87a5d60103 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-28 00:15:19 +02:00
Marek Vasut
3ff915e886 GCC4.6: Squash warnings in omap4 clocks.c
clocks.c:606:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'u32 * const'
clocks.c:633:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'u32 * const'

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-27 23:54:09 +02:00
Ricardo Salveti de Araujo
53430a4f25 omap4: splitting padconfs into common, 4430 and 4460
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).

Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:34 +02:00
Ricardo Salveti de Araujo
8f6a027f62 omap4: adding revision detection for 4460 ES1.1
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>

 2 files changed, 17 insertions(+), 1 deletions(-)
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:33 +02:00
Ricardo Salveti de Araujo
20033c9f87 omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
OMAP4460 has a different set of values for the ID code, so moving the
old ones to be related just with 4430.

Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-10-27 21:56:33 +02:00
Simon Schwarz
63ffcfcbd0 omap-common/omap4: relocate early UART clock setup
Moves the early UART clock setup setup_clocks_for_console() from
preloader_console_init() to s_init() of OMAP4.

This is done to prepare for OMAP3 integration.

This patch was posted seperatly to the mailinglist but I decidet - since it is
a prereqesit for this patch to add it. Former port to ML:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30 22:00:54 +02:00
Aneesh V
4ecfcfaa9e omap4: IO settings
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:25:16 +02:00
Aneesh V
025bc4254b omap4: make SDRAM init work for ES1.0 silicon
SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:25:15 +02:00
Sanjeev Premi
3b690ebbbf omap: gpio: generic changes after changing API
This patch contains the generic changes required after
change to generic API in the previous patch.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:25:15 +02:00
Aneesh V
13d4f9bd74 omap: enable caches at system start-up
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04 11:36:16 +02:00
Aneesh V
080a46eaf1 omap: fix gpio related build breaks
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
2011-09-04 11:33:36 +02:00
Aneesh V
b4dc644291 omap4: clock init support for omap4460
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
d506719f7f omap4: support TPS programming
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.

VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
25223a68e5 omap: reuse omap3 gpio support in omap4
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
924eb369e3 omap4: sdram init changes for omap4460
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
5ab12a9eeb omap4: add omap4460 revision detection
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
John Rigby
3decb14abe mkimage: Add OMAP boot image support
- Add mkimage support for OMAP boot image
- Add support for OMAP boot image(MLO) generation in the new
  SPL framework

Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
8cf686e19b omap: add MMC and FAT support to SPL
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
  can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
  and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
  payload size and load address from this header. If the
  header is not detected assume u-boot.bin as payload

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
bcae721162 omap: add basic SPL support
- Provide alternate implementations of board_init_f()
  board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
  it to board config header from config.mk

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:20 +02:00
Aneesh V
1e463866f5 omap4: automatic sdram detection
Identify SDRAM devices connected to EMIF automatically:
LPDDR2 devices have some Mode Registers that provide details
about the device such as the type, density, bus width
etc. EMIF has the capability to read these registers. If there
are no devices connected to a given chip-select reading mode
registers will return junk values. After reading as many such
registers as possible and matching with expected ranges of
values the driver can identify if there is a device connected
to the respective CS. If we identify that a device is connected
the values read give us complete details about the device.

This along with the base AC timings specified by JESD209-2
allows us to do a complete automatic initialization of
SDRAM that works on all boards.

Please note that the default AC timings specified by JESD209-2
will be safe for all devices but not necessarily optimal. However,
for the Elpida devices used on Panda and SDP the default timings
are both safe and optimal.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Aneesh V
095aea293b omap4: calculate EMIF register values
Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.

For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Aneesh V
2ae610f030 omap4: add sdram init support
Add support for the SDRAM controller (EMIF).

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Aneesh V
3776801d0a omap4: add clock support
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails

This work draws upon previous work done for x-loader by:
	Santosh Shilimkar <santosh.shilimkar@ti.com>
	Rajendra Nayak <rnayak@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Aneesh V
ad577c8a48 omap4: add OMAP4430 revision check
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00