Commit graph

202 commits

Author SHA1 Message Date
Stephen Warren
7fb82986be ARM: tegra: rm Jetson TK1 PMIC GPIO programming
The PMIC is configured such that its GPIOs have the correct configuration
at power-up, so no programming is required.

In fact, the current programming is actively wrong, since:

(a) the AS3722 driver configures the GPIO to be an output before setting
its output value, which causes a 0v glitch on the output.

(b) the AS3722 driver configures the GPIO to drive a high voltage from its
VSUP_GPIO power source rather than its VDD_GPIO_LV power source, so the pin
drives 5V not 1.8V as desired.

Solve these problems by removing the code which configures the PMIC GPIOs.

Note that this patch was tested directly on top of v2016.01; since then,
commit 96350f729c "dm: tegra: net: Convert tegra boards to driver model
for Ethernet" prevents PCIe from being initialized. Alternatively, simply
revert that commit to get PCIe Ethernet working again, then apply this
patch to test.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-01-28 10:32:31 -07:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Simon Glass
96350f729c dm: tegra: net: Convert tegra boards to driver model for Ethernet
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12 10:19:09 -07:00
Alexandre Courbot
d6bf06c0c7 ARM: tegra: simplify GPU setup
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.

Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:07 -07:00
Stephen Warren
019bc6259d ARM: tegra: enable PCI support of p2371-2180
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-11-12 09:21:06 -07:00
Tom Rini
da58dec866 Various Makefiles: Add SPDX-License-Identifier tags
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one.  This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:19:52 -05:00
Stephen Warren
cb96bf991b ARM: tegra: p2371-2180: import latest pinmux
In order to avoid any assumptions about any device connected to
P2371-2180's expansion connector, the latest pinmux spreadsheet
configures all muxable pins on that connector to be GPIO inputs, with
on-chip pulls where appropriate.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-10-02 11:04:05 -07:00
Stephen Warren
2573428140 ARM: tegra: Add p2371-2180 board
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-09-16 16:10:22 -07:00
Stephen Warren
f05fa6781a ARM: tegra: Add p2371-0000 board
P2371-0000 is a P2581 or P2530 CPU board married to a P2595 I/O
board. The combination contains SoC, DRAM, eMMC, SD card slot,
HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
a GPIO expansion header, and an analog audio jack.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-06 10:50:04 -07:00
Stephen Warren
b6920095c5 ARM: tegra: Add e2220-1170 board
E2220-1170 is a Tegra210 bringup board with onboard SoC, DRAM,
eMMC, SD card slot, HDMI, USB micro-B port, and sockets for various
expansion modules.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-06 10:50:03 -07:00
Alexandre Courbot
a38a3c4af4 ARM: tegra: enable GPU DT node when appropriate
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.

Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-06 10:50:03 -07:00
Stephen Warren
95486f843b ARM: tegra: add comment re: autogeneration to pinmux headers
Add a comment block to the top of each generated Tegra pinmux header file
indicating that the file was auto-generated, should not be manually
edited, and with a pointer to the tool and command used to generate it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-06 10:50:02 -07:00
Tom Warren
66999892b2 T210: P2571: Turn CPU fan on
CPU board (E2530) has a fan - turn it on via GPIO to keep
the SoC cool.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-05 15:22:51 -07:00
Tom Warren
4132bc90e6 T210: P2571: Enable SD-card power via PMIC LDO2
This was done in the 32-bit AVP loader (SPL) but is
board-specific so should be moved to the CPU portion.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
2015-08-05 15:22:51 -07:00
Tom Warren
873e3ef90b T210: Add support for 64-bit T210-based P2571 board
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.

With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).

Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-07-28 10:30:20 -07:00
Simon Glass
6a6800bfb7 tegra: nyan-big: Allow TPM on I2C
Enable the I2C3 pins so that the TPM can be used.

Note: There is an DP change also, caused by running board-to-uboot.py
script in the latest tegra-pinmux-script tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-07-27 14:03:07 -07:00
Simon Glass
f3746621f1 tegra: Replace 'Norrin' with 'Nyan-big' and fix typo
With the rename the MAINTAINER file was not updated. Fix it and the
'Chrombook' typo in Kconfig.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-06-09 09:56:15 -07:00
Simon Glass
7cfde8117f tegra: nyan-big: Add additional clock and kernel init
We need to turn on all audio-related clocks for the Chrome OS kernel to
boot. Otherwise it will hang when trying to enable audio.

Also for Linux set up graphics driver video protection.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-06-09 09:56:15 -07:00
Masahiro Yamada
237c36379c ARM: tegra: move NVIDIA common files to arch/arm/mach-tegra
All the Tegra boards borrow the files from board/nvidia/common/
directory, i.e., board/nvidia/common/* are not vendor-common files,
but SoC-common files.

Move NVIDIA common files to arch/arm/mach-tegra/ to clean up
Makefiles.

As arch/arm/mach-tegra/board.c already exists, this commit renames
board/nvidia/common/board.c to arch/arm/mach-tegra/board2.c,
expecting they will be consolidated as a second step.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:46:19 -07:00
Simon Glass
0deba29c20 tegra: nyan-big: Add LCD PMIC init and board ID
Add required setup for the LCD display, and a function to provide the
board ID. This requires GPIOs to be available prior to relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:08 -07:00
Simon Glass
346451b588 tegra: Add support for setting up a as3722 PMIC
Add support for this PMIC which is used on some Tegra124 boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:08 -07:00
Simon Glass
8277636420 tegra: Provide a function to allow LCD PMIC setup
Some LCDs require a PMIC to be set up - add a function for this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:08 -07:00
Simon Glass
ec74664434 tegra: Add a board ID function
Add a way of displaying a numeric board ID on start-up.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:07 -07:00
Simon Glass
7d874132c4 tegra: Move checkboard() into the board code
This is only used by Nvidia boards, so move it into nvidia/common to
simplify things.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:07 -07:00
Simon Glass
37220efab8 tegra: seaboard: Correct the gpio_request() call
Requesting a GPIO without a name is not supposed anymore. This causes the
request to fail. Add a name so that the serial console works on seaboard.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-30 09:59:58 -07:00
Tom Rini
b79dadf846 Merge branch 'master' of git://git.denx.de/u-boot-tegra
Conflicts:
	README

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-10 19:09:18 -04:00
Simon Glass
bdfb34167f dm: tegra: Enable driver model in SPL and adjust the GPIO driver
Use the full driver model GPIO and serial drivers in SPL now that these are
supported. Since device tree is not available they will use platform data.

Remove the special SPL GPIO function as it is no longer needed.

This is all in one commit to maintain bisectability.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-03-04 14:55:04 -05:00
Stephen Warren
c1fe92fe29 ARM: tegra: import latest Jetson TK1 pinmux
Syseng has revamped the Jetson TK1 pinmux spreadsheet, basing the content
completely on correct configuration for the board/schematic, rather than
the previous version which was based on the bare minimum changes relative
to another reference board.

The new spreadsheet sets TRISTATE for any input-only pins. This only works
correctly if the global CLAMP bit is not set, so the Jetson TK1 board code
has been adjusted accordingly. Apparently syseng have changed their mind
since the previous advice that this needed to be set:-/

This content comes from Jetson_TK1_customer_pinmux.xlsm (v09) downloaded
from https://developer.nvidia.com/hardware-design-and-development.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-04 10:08:58 -07:00
Stephen Warren
73c38934da ARM: tegra: support running in non-secure mode
When the CPU is in non-secure (NS) mode (when running U-Boot under a
secure monitor), certain actions cannot be taken, since they would need
to write to secure-only registers. One example is configuring the ARM
architectural timer's CNTFRQ register.

We could support this in one of two ways:
1) Compile twice, once for secure mode (in which case anything goes) and
   once for non-secure mode (in which case certain actions are disabled).
   This complicates things, since everyone needs to keep track of
   different U-Boot binaries for different situations.
2) Detect NS mode at run-time, and optionally skip any impossible actions.
   This has the advantage of a single U-Boot binary working in all cases.

(2) is not possible on ARM in general, since there's no architectural way
to detect secure-vs-non-secure. However, there is a Tegra-specific way to
detect this.

This patches uses that feature to detect secure vs. NS mode on Tegra, and
uses that to:

* Skip the ARM arch timer initialization.

* Set/clear an environment variable so that boot scripts can take
  different action depending on which mode the CPU is in. This might be
  something like:
  if CPU is secure:
    load secure monitor code into RAM.
    boot secure monitor.
    secure monitor will restart (a new copy of) U-Boot in NS mode.
  else:
    execute normal boot process

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-04 10:08:57 -07:00
Simon Glass
25ab4b0303 dm: i2c: Provide an offset length parameter where needed
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
2015-01-29 17:09:53 -07:00
Simon Glass
f9a4c2da72 dm: i2c: Rename driver model I2C functions to permit compatibility
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.

This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers are
converted to use driver model for I2C.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:53 -07:00
Masahiro Yamada
13e55b358e ARM: remove redudant information from Kconfig files
- "string" type for SYS_* is defined in arch/Kconfig
 - SYS_CPU "armv7" has been replaced with "select CPU_V7"
 - SYS_SOC "tegra124" is already defined in tegra124/Kconfig

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
2015-01-12 09:38:47 -05:00
Thierry Reding
6e2fca94ff ARM: tegra: Enable PCIe on Jetson TK1
The Jetson TK1 has an ethernet NIC connected to the PCIe bus and routes
the second root port to a miniPCIe slot. Enable the PCIe controller and
the network driver to allow the device to boot over the network.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-12-18 13:19:21 -07:00
Thierry Reding
5a2c96a0e5 ARM: tegra: Enable PCIe on Cardhu
The PCIe bus on Cardhu is routed to the dock connector. An ethernet NIC
is available on the dock over the PCIe bus. Enable the PCIe controller
and the network device driver so that the device can boot over the
network.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-12-18 13:19:21 -07:00
Thierry Reding
79c7a90f6c ARM: tegra: Implement XUSB pad controller
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.

Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-12-18 13:19:20 -07:00
Simon Glass
b0e6ef4640 dm: i2c: tegra: Convert to driver model
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:

   - CONFIG_SYS_I2C_INIT_BOARD
   - CONFIG_I2C_MULTI_BUS
   - CONFIG_SYS_MAX_I2C_BUS
   - CONFIG_SYS_I2C_SPEED
   - CONFIG_SYS_I2C

This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1

It has not been tested on Tegra 114 as I don't have that board.

Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-12-11 13:18:44 -07:00
Allen Martin
a6c7b46181 ARM: tegra: Add support for nyan-big board
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.

This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.

The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.

Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
2014-12-11 13:18:44 -07:00
Simon Glass
0521f98427 dm: tegra: Add platform data for the GPIO driver
Add platform data for the GPIO driver. It doesn't need to contain anything
since the GPIO driver will actually use information from the CONFIGs for
now. This merely serves to ensure that the GPIO driver is bound.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 08:14:07 +01:00
Jeroen Hofstee
19d7bf3d86 tegra: make local functions static
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:27:37 -04:00
Tom Rini
03a3536c7b Merge branch 'master' of git://git.denx.de/u-boot-tegra 2014-10-23 14:05:34 -04:00
Simon Glass
fda6fac39b dm: tegra: spi: Convert to driver model
This converts the Tegra SPI drivers to use driver model. This is tested
on:

- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore

(not tested on Tegra124)

Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22 10:36:52 -06:00
Stephen Warren
606f5bc812 ARM: tegra: add PCIe-related pins to the Jetson TK1 pinmux tables
This pinmux tables currently omit any configuration for PCIe clk_req,
wake, and rst pins, which in turn causes intermittent failures in
U-Boot's PCIe support. Import an updated version of the pinmux tables
which rectifies this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-10-22 09:30:54 -07:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Simon Glass
2fccd2d96b tegra: Convert tegra GPIO driver to use driver model
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.

The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.

The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.

Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 12:59:59 -06:00
Masahiro Yamada
ddd960e6c4 tegra: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.

Insert the Tegra SoC select menu between the arch select and the
board select.

 Architecture select
 |-- Tegra Platform (Tegra)
     |- Tegra SoC select (Tegra20 / 30 / 114 / 124)
        |- Board select

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:

  config TEGRA
          bool
          select SPL

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2014-08-30 21:19:32 -04:00
Stephen Warren
a78cf41e79 ARM: tegra: remove custom define for Jetson TK1
Now that Kconfig has a per-board option, we can use that directly rather
than inventing a custom define for the AS3722 code to determine which
board it's being built for.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-08-19 08:44:03 -07:00
Masahiro Yamada
93d4334f7f Add board MAINTAINERS files
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:06 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Stephen Warren
3365479ce7 ARM: tegra: Venice2 pinmux spreadsheet updates
The Venice2 pinmux spreadsheet was updated to fix a few issues. Import
those changes into the U-Boot pinmux initialization tables.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00
Stephen Warren
2eba87a30a ARM: tegra: update Venice2 pinmux
This re-imports the entire Venice2 pinmux data from the board's master
spreadsheet, and makes use of the new IO clamping GPIO initialization
table features. This makes the board port fully compliant with the
required HW-defined pinmux initialization sequence.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:32 -07:00