Commit graph

48 commits

Author SHA1 Message Date
Stephen Warren
68295a48bf ARM: tegra: enable filesystem writing
Writing to files is a useful feature in general, so enable it everywhere.
The primary purpose is to make DFU useful on filesystems in addition to
raw devices.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2015-09-11 17:15:25 -04:00
Stephen Warren
99d969612f ARM: tegra: fix malloc region sizing
Commit 52a7c98a17 "tegra-common: increase malloc pool len by dfu mmc
file buffer size" updated the definition of CONFIG_SYS_MALLOC_LEN for
Tegra to take account of the DFU buffer size. However, this change had
no effect, since typical Tegra board config headers don't set the DFU-
related defines until after tegra-common.h is included. Fix this by
moving the affected conditional code to tegra-common-post.h, which is
included last. Also move the definition of SYS_NONCACHED_MEMORY since
it's a related and adjacent definition.

Fix the condition to test for the DFU feature, rather than specifically
MMC DFU support, so it applies in all cases.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
2015-09-11 17:15:24 -04:00
Stephen Warren
bbc1b99e8b ARM: tegra: represent RAM in 1 or 2 banks
Represent all available RAM in either one or two banks. The first bank
describes any RAM below 4GB. The second bank describes any RAM above 4GB.

This split is driven by the following requirements:
- The NVIDIA L4T kernel requires separate entries in the DT /memory/reg
  property for memory below and above the 4GB boundary. The layout of that
  DT property is directly driven by the entries in the U-Boot bank array.
- On systems with RAM beyond a physical address of 4GB, the potential
  existence of a carve-out at the end of RAM below 4GB can only be
  represented using multiple banks, since usable RAM is not contiguous.

While making this change, add a lot more comments re: how and why RAM is
represented in banks, and implement a few more "semantic" functions that
define (and perhaps later detect at run-time) the size of any carve-out.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-08-13 13:06:04 -07:00
Nikita Kiryanov
181bd9dc61 kconfig: add config option for shell prompt
Add option to set shell prompt string from menuconfig and migrate
boards globally.

The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
  entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
  CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
  right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
  CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
  files. This results in a streamlined default value across platforms, and
  includes the following files: spear-common, sunxi-common, mv-common,
  ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
  not updated in their respective defconfig files under the assumption that
  since they did not explicitly define a value, they're fine with whatever
  the default is.
- On the other hand, boards that relied on a value defined in some
  <boards>_common.h file such as woodburn_common, rpi-common,
  bur_am335x_common, ls2085a_common, siemens_am33x_common, and
  omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
  assigning a value for CONFIG_SYS_PROMPT.

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-08-13 07:19:33 -04:00
Thierry Reding
f41f0a1918 ARM: tegra: Use architected timer on ARMv8
ARMv8 requires an architected timer to be present, so it can be used
instead of the Tegra US timer. This allows for better code reuse.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-07-28 10:30:18 -07:00
Thierry Reding
6527268d6e ARM: tegra: Disable SPL and non-cached memory on 64-bit
For 64-bit ARM SoCs we rely on non-U-Boot code to bring up the CPU in
AArch64 mode so that we don't need the SPL. Non-cached memory is not
implemented (yet) for 64-bit ARM.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2015-07-28 10:30:18 -07:00
Joe Hershberger
ef0f2f5752 Move defaults from config_cmd_default.h to Kconfig
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-06-25 22:18:34 -04:00
Simon Glass
0859b49d12 tegra: Increase maximum arguments to 32
When setting up large environment variables we can exceed 16 arguemnts.
Increase this to avoid problems.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-06-09 09:56:14 -07:00
Joe Hershberger
6eed3786c6 net: Move the CMD_NET config to defconfigs
This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a8 (commands: add more
command entries in Kconfig).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-01 09:40:15 -05:00
Stephen Warren
86bd20b007 ARM: tegra: enable STDIO deregistration
At the very least when USB keyboard support is enabled, we need to enable
CONFIG_SYS_STDIO_DEREGISTER, so the "usb reset" is able to re-scan USB
ports and find new devices. Enable it everywhere per request from Simon
Glass.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:12 -07:00
Tom Rini
b79dadf846 Merge branch 'master' of git://git.denx.de/u-boot-tegra
Conflicts:
	README

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-03-10 19:09:18 -04:00
Przemyslaw Marczak
52a7c98a17 tegra-common: increase malloc pool len by dfu mmc file buffer size
The dfu mmc file buffer, which was static, now is allocated
by memalign(), so the malloc pool len should be also increased.

Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Tom Warren <twarren.nvidia@gmail.com>
2015-03-09 11:13:29 -04:00
Simon Glass
bdfb34167f dm: tegra: Enable driver model in SPL and adjust the GPIO driver
Use the full driver model GPIO and serial drivers in SPL now that these are
supported. Since device tree is not available they will use platform data.

Remove the special SPL GPIO function as it is no longer needed.

This is all in one commit to maintain bisectability.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-03-04 14:55:04 -05:00
Stephen Warren
026baff755 ARM: tegra: move common config defines centrally
All boards need CONFIG_BOARD_EARLY_INIT_F, and many actively need
CONFIG_BOARD_LATE_INIT. Move both of these into tegra-common.h so that
board config headers don't need to repeatedly define them.

Later commits will add new code in board_late_init() which applies to
all boards, so CONFIG_BOARD_LATE_INIT should be enabled for all Tegra
boards.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-03-04 10:08:56 -07:00
Simon Glass
b724bd7d63 dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to Kconfig
Move this option to Kconfig and update all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 15:17:28 -07:00
Simon Glass
d7a4b2e42e dm: tegra: Move driver model CONFIGs to Kconfig
Remove driver model CONFIGs from the board config headers and use Kconfig
instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-02-12 10:35:34 -07:00
Thierry Reding
d1e5b4065e ARM: tegra: Enable non-cached memory
Some boards, most notably those with a PCIe ethernet NIC, require this
to avoid cache coherency problems. Since the option adds very little
code and overhead enable it across all Tegra generations. Other drivers
may also start supporting this functionality at some point, so enabling
it now will automatically reap the benefits later on.

Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-12-18 13:21:41 -07:00
Simon Glass
b0e6ef4640 dm: i2c: tegra: Convert to driver model
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:

   - CONFIG_SYS_I2C_INIT_BOARD
   - CONFIG_I2C_MULTI_BUS
   - CONFIG_SYS_MAX_I2C_BUS
   - CONFIG_SYS_I2C_SPEED
   - CONFIG_SYS_I2C

This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1

It has not been tested on Tegra 114 as I don't have that board.

Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-12-11 13:18:44 -07:00
Simon Glass
9dacbb2772 dm: tegra: Avoid using arch-specific memcpy() in SPL
The faster functions are not actually available in SPL and the code size
likely isn't worth it. Use the normal memcpy() in SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 08:11:13 +01:00
Tom Rini
03a3536c7b Merge branch 'master' of git://git.denx.de/u-boot-tegra 2014-10-23 14:05:34 -04:00
Masahiro Yamada
45ccec8f29 kconfig: move CONFIG_USE_PRIVATE_LIBGCC to Kconfig
The private libgcc is supported only on ARM, MIPS, PowerPC, SH, x86.
Those architectures should "select" HAVE_PRIVATE_LIBGCC and
CONFIG_USE_PRIVATE_LIBGCC should depend on it.

Currently, this option is enabled on Tegra boards and x86 architecture.
Move the definition from header files to Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2014-10-23 13:19:09 -04:00
Simon Glass
fda6fac39b dm: tegra: spi: Convert to driver model
This converts the Tegra SPI drivers to use driver model. This is tested
on:

- Tegra20 - trimslice
- Tegra30 - beaver
- Tegra124 - dalmore

(not tested on Tegra124)

Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-22 10:36:52 -06:00
Marcel Ziswiler
4270d5afed arm: tegra: use architecture specific memcpy
Use architecture specific memcpy to speed up things.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-10-22 09:30:54 -07:00
Simon Glass
858530a8c0 dm: tegra: Enable driver model for serial
Use driver model for serial ports.

Since Tegra now uses driver model for serial, adjust the definition of
V_NS16550_CLK so that it is clear that this is only used for SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 13:00:02 -06:00
Simon Glass
2fccd2d96b tegra: Convert tegra GPIO driver to use driver model
This is an implementation of GPIOs for Tegra that uses driver model. It has
been tested on trimslice and also using the new iotrace feature.

The implementation uses a top-level GPIO device (which has no actual GPIOS).
Under this all the banks are created as separate GPIO devices.

The GPIOs are named as per the Tegra datasheet/header files: A0..A7, B0..B7,
..., Z0..Z7, AA0..AA7, etc.

Since driver model is not yet available before relocation, or in SPL, a
special function is provided for seaboard's SPL code.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 12:59:59 -06:00
Simon Glass
a47411110c dm: tegra: Set up a pre-reloc malloc()
Allocate 1KB so that driver model can operate before relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-10 12:59:58 -06:00
Masahiro Yamada
ddd960e6c4 tegra: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.

Insert the Tegra SoC select menu between the arch select and the
board select.

 Architecture select
 |-- Tegra Platform (Tegra)
     |- Tegra SoC select (Tegra20 / 30 / 114 / 124)
        |- Board select

Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:

  config TEGRA
          bool
          select SPL

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
25b4adbba0 include: remove CONFIG_SPL/CONFIG_TPL definition in config headers
Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig.

Remove the redundant definition in config headers.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 14:42:03 -04:00
Masahiro Yamada
4ce9957029 include: define CONFIG_SPL and CONFIG_TPL as 1
We are about to switch to Kconfig in the next commit.
But there are something to get done beforehand.

In Kconfig, include/generated/autoconf.h defines boolean
CONFIG macros as 1.

CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1.
Otherwise, when switching to Kconfig, the build log
would be sprinkled with warning messages like this:
  warning: "CONFIG_SPL" redefined [enabled by default]

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:02 -04:00
Simon Glass
47f3d3c80b tegra: Enable driver model
Enable driver model for Tegra boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-06-20 11:56:47 -06:00
Stephen Warren
f175603f7c ARM: tegra: set CONFIG_SYS_MMC_MAX_DEVICE
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.

A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE

1) It isn't documented in README. The same is true for a lot of similar
   defines used by api_storage.c.

2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
   valid values are 0..n-1 not 0..n.

However, I this patch does not address those shortcomings.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-05-13 10:41:31 -07:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Masahiro Yamada
cd2e46cb38 kbuild: add CONFIG_ prefix to USE_PRIVATE_LIBGCC
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.

We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.

By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)

Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.

It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding

  #ifdef CONFIG_SPL_BUILD
  # define CONFIG_USE_PRIVATE_LIBGCC
  #endif

to include/configs/tegra-common.h.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
2014-03-07 10:59:06 -05:00
Stephen Warren
68cf64db1d ARM: tegra: convert tegra to use distro defaults
Modify all Tegra boards to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the Tegra files.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Rob Herring
31df9893b9 ARM: tegra: convert to common timer code
Convert tegra to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:24:22 -05:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Stephen Warren
8258c12614 ARM: tegra: support raw ramdisks
This way, we don't have to run mkimage on them.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-08-19 15:31:37 -07:00
Thierry Reding
0d79f4f490 ARM: tegra: Make cache line size SoC specific
Currently all Tegra SoCs are assumed to have 32 byte cache lines. This
isn't true for Tegra114, however, which uses 4 Cortex-A15 cores and
therefore uses a cache line size of 64 bytes. Move the cache line size
setting to the per-SoC common configuration file.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-08-19 15:31:37 -07:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Warren
3efff99fbd Tegra: enable verify support for the crc32 command
Some 3rd-party flash tools use the -v (verify) option of crc32 command.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2013-04-15 11:01:37 -07:00
Albert ARIBAUD
6ebc346111 ARM: fix CONFIG_SPL_MAX_SIZE semantics
Remove SPL-related ASSERT() in arch/arm/cpu/u-boot.lds
as this file is never used for SPL builds.

Rewrite the ASSERT() in arch/arm/cpu/u-boot-spl.lds
to separately test image (text,data,rodata...) size,
BSS size, and full footprint each against its own max,
and make Tegra boards check full footprint.

Also, output section mmutable is not used in SPL builds.
Remove it.

Finally, update README regarding the (now homogeneous)
semantics of CONFIG_SPL_[BSS_]MAX_SIZE and add the new
CONFIG_SPL_MAX_FOOTPRINT macro.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-14 16:07:14 +02:00
Tom Rini
0ce033d258 Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end.  We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.

Conflicts:
	arch/arm/cpu/ixp/u-boot.lds
	arch/arm/cpu/u-boot.lds
	arch/arm/lib/Makefile
	board/actux1/u-boot.lds
	board/actux2/u-boot.lds
	board/actux3/u-boot.lds
	board/dvlhost/u-boot.lds
	board/freescale/mx31ads/u-boot.lds
	doc/README.scrapyard
	include/configs/tegra-common.h

Build tested for all of ARM and run-time tested on am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-18 14:37:18 -04:00
Simon Glass
dd7f65f664 tegra: Enable generic board for Tegra
Bravely enable CONFIG_SYS_GENERIC_BOARD for all Tegra boards.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-15 16:14:01 -04:00
Stephen Warren
11d9c03039 ARM: tegra: enable a common set of disk-related commands everywhere
Enable a common set of partition types, filesystems, and related
commands in tegra-common.h, so that they are available on all Tegra
boards. This allows boot.scr (loaded and executed by the default
built-in environment) on those boards to assume that certain features
are always available.

Do this in tegra-common.h, so that individual board files can undefine
the features if they really don't want any of them.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-14 11:06:45 -07:00
Stephen Warren
a885f85214 ARM: tegra: make bounce buffer option common
All Tegra devices will need CONFIG_BOUNCE_BUFFER. Move it to
tegra-common.h to ensure it's always set.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-03-14 11:06:44 -07:00
Tom Warren
bfcf46db63 Tegra: Remove unused CONFIG_SYS_CPU_OSC_FREQUENCY define
This wasn't used anywhere in any Tegra build.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-03-14 11:06:43 -07:00
Tom Warren
f01b631f7d Tegra30: Add/enable Cardhu build (T30 reference board)
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.

include/configs/tegra-common.h now holds common config options
for Tegra SoCs.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
2013-01-16 13:40:08 -07:00