NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
Based on our usage of the GPMC, either with NOR or NAND we do not need
to be setting the irqstatus or irqenable bits and should clear them like
we have historically.
Signed-off-by: Tom Rini <trini@ti.com>
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
- Style cleanup (# define -> #define)
- Due to ROM issues, redudant loading isn't feasible, so drop.
- Given extra space, increase max size of U-Boot to 512KiB
- Correct env size to match usage (we had not re-defined ENV_SIZE).
- Given extra space, keep env size as 128KiB, add redundant environment.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
We always set a CONFIG_ENV_IS_...somewhere... so drop the initial define
of NOWHERE.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
The AM335x GP EVM ships with NAND. Document programming of the chip
including the redundant locations that the ROM will check.
Signed-off-by: Tom Rini <trini@ti.com>
If no other bootoption works, try loading up device tree and zImage.
This is selected as the last option to allow backward compatibility as
well as support the recent trend in moving kernel boot to using zImage
and device tree.
NOTE: if uImage is present in bootpart, it will try this first and
will assume this is to be booted with bootm (so may be concatenated
image or plain vanilla ATAG MACHINE_ID based image)
Signed-off-by: Nishanth Menon <nm@ti.com>
For folks not using concatenated device tree with uImage, having
an handy function to find and load device tree is very handy.
So introduce findfdt and loadfdt and run findfdt by default to make
it easier on user scripts.
Signed-off-by: Nishanth Menon <nm@ti.com>
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we currently use. Sticking with existing conventions,
defaults will be:
ramdisk=ramdisk.gz
bootpart=0:2 (second partition)
bootdir=/boot (/boot in second partition)
This matches with the default behavior, these can be overriden by
env files as needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
As reported in http://marc.info/?l=u-boot&m=137358037827735&w=2
There is no need for the "xMB" variant, as the gpio pins used for
identification where never changed from the xMA when the newer silcon
was used for the xMB, So rename XM A revision as AB revision
and report accordingly
Reported-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
e682930867
(BeagleBoard: config: use uImage.beagle for tftp)
Introduced uImage.beagle which does not happen to be default output
file of Linux kernel build make uImage (output is uImage).
So, replace uImage.beagle with uImage
Signed-off-by: Nishanth Menon <nm@ti.com>
We do not use JFFS2 by default and it conflicts with
CONFIG_CMD_FS_GENERIC (ls command is the same). Since most of our
BOOTCMD can be simplified by using the FS_GENERIC, dropping JFFS2
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
Locking DPLL_GMAC
[mugunthanvnm@ti.com:Configure only if CPSW is selected]
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Add a README for the family of boards the am335x_evm covers, and include
instructions on preparing and using falcon mode, for various media.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion
of falcon mode to NAND. Previously it was half the size of the
eraseblock which is too small, increase to eraseblock size.
Signed-off-by: Tom Rini <trini@ti.com>
The previous location used for the "args" portion of falcon mode was too
small to allow for a device tree to be saved there, so move the location
slightly and increase the size. In addition, our previous kernel
location was part of the area we set aside for U-Boot itself, so move it
up a bit higher.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Now that we have falcon mode enabled, the partiton numbers for NAND have
changed, and we need to list entries for updating these parts of the
system. While adding falcon mode entires for eMMC (raw), we round up
the limit on U-Boot for ease of math later.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
The OMAP36xx/OMAP37xx family uses L3 frequency of 200MHz instead of 165MHz
used by OMAP34xx/OMAP35xx.
Also fix checkpatch warning about alignment.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Currently, we assume that if we can read from MMC correctly, we have
found a valid image. This is not the case as an empty area will read
just fine. Add a check for a valid IH_MAGIC.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
The current code uses clrbits_be32 which is incorrect since we are on
a little endian machine here. This patch fixes this issue and also removes
some unnecessary code: Reading the current GPIO bank state is not required
if we are using the SET and CLEAR GPIO registers for setting/clearing
bits.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Cc: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Currently in OMAP3 SPL, the GPMC for NAND is configured for 16bit
access. This patch adds support for 8bit NAND devices as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Conflict over SPDX changes means that one change was effectively dropped
as it was fixing typos in a removed hunk of text.
Conflicts:
arch/mips/cpu/mips64/start.S
Signed-off-by: Tom Rini <trini@ti.com>
Because the SOCFPGA platform will include support for Cyclone V and
Arria V FPGA parts, renaming socfpga_cyclone5 folder to socfpga to
be more generic.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
v2:
- Add Reviewed-by: Pavel Machek
- Cc: Tom Rini
Some version of Andes core support FPU coprocessor,
if this is the case, and toolchain support FPU instruction set,
we should enable it at low level initialization time.
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
Restrict autoboot interruption to "s" or "d" keys. This will prevent some
unwanted stopping and also allow disabling the reset on command timeout.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Accessing powered down peripherals will hang the bus, so check power
domain status before initializing SATA and fixup the FDT to disable
unused peripherals.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The timer_init function is called before relocation and writes to bss data
were corrupting relocation data. Fix this by removing the call to
reset_timer_masked. The initial timer count should be 0 or near 0 anyway,
so initializing the variables are not needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The 150MHz clock rate gives u-boot time functions problems and there's no
benefit to a fast clock, so lower the rate.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Various changes to highbank config:
Enable EFI partitions
Enable ext4 and FAT filesystems
Enable bootz command and raw initrd
Increase cmd and print buffer size to 1K
Change serial baudrate to 115200
Enable hush shell
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
There is no reason to wait for the entire frame to start DMA on receive,
so enable rx cut-thru for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
interrupt_init also sets up the abort stack, but is not setup before
relocation. So any aborts during relocation will hang and not print out
any useful information. Fix this by moving the interrupt_init to after
the stack setup in board_init_f.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Synchronize the code with mips64/cache.S, in order to
allow further unifications.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Tom Rini
Steve Kipisz
Nishanth Menon
Mugunthan V N
Lokesh Vutla
Andreas Bießmann
Christian Riesch
Stefan Roese
Albert ARIBAUD
Dinh Nguyen
ken kuo
Rob Herring
Gabor Juhos