Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds the microcode blob for BayTrail-I B0 stepping,
CPUID signature 30671h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a cpu1 node to the device tree and enable the MP initialization
on QEMU targets (i440fx and q35).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add a RTC node in the device tree to enable DM RTC support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
(Squashed in 'x86: Fix RTC build error on ivybridge')
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 4 usb ports on the Intel Crown Bay board, 2 of which are
connected to Topcliff usb host 0 and the other 2 connected to usb
host 1. USB devices inserted in the ports connected to usb host 1
cannot get detected due to wrong IRQ assigned to the controller.
Actually we need apply the PCI interrupt pin swizzling logic to all
devices on the Topcliff chipset when configuring the PIRQ routing.
This was observed on usb ports, but device 6 and 10 irqs are also
wrong. Correct them all together.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Crown Bay board has a TunnelCreek processor which supports
hyper-threading. Add /cpus node in the crownbay.dts and enable
the MP initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(modified to remove error:
overriding the value of OF_CONTROL. Old value: "y", new value: "y")
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
Support QEMU PIRQ routing via device tree on both i440fx and q35
platforms. With this commit, Linux booting on QEMU from U-Boot
has working ATA/SATA, USB and ethernet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Writing 0xcb to I/O port 0xb2 (Advanced Power Management Control) causes
U-Boot to hang on QEMU q35 target. We introduce a config option in the
device tree "u-boot,no-apm-finalize" under /config node if we don't want
to do that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Although the two qemu-x86 targets (i440fx and q35) share a lot in
common, they still have something that cannot easily handled in one
single device tree). Split to create two dedicated device tree files
and make the i440fx be the default build target.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
Enable the CPU uclass and Simple Firmware interface for Minnowbaord MAX. This
enables multi-core support in Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot on coreboot does not have a driver for the PCH so cannot see the
SPI peripheral now that it has moved inside the PCH. Add a simple driver so
that SPI flash works again.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPI NOR on the minnowboard max is a MICRON N25Q064A
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 6 banks:
4 banks for CORE: available in S0 mode
2 banks for SUS (Suspend): available in S0-S5 mode
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since Intel ICH SPI driver has been converted to driver model, we need
add an alias for SPI node in the board dts files otherwise SPI flash
won't be detected due to 'invalid bus' error.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) is on the PCI bus, so show it as such.
The LPC (Low Pin Count) and SPI bus are inside the PCH, so put these in the
right place also.
Rename the compatible strings to be more descriptive since this board is the
only user. Once we are using driver model fully on x86, these will be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move chromebook_link over to driver model for PCI.
This involves:
- adding a uclass for platform controller hub
- removing most of the existing PCI driver
- adjusting how CPU init works to use driver model instead
- rename the lpc compatible string (it will be removed later)
This does not really take advantage of driver model fully, but it does work.
Furture work will improve the code structure to remove many of the explicit
calls to init the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support running U-Boot as a coreboot payload. Tested peripherals include:
- Video (HDMI and DisplayPort)
- SATA disk
- Gigabit Ethernet
- SPI flash
USB3 does not work. This may be a problem with the USB3 PCI driver or
something in the USB3 stack and has not been investigated So far this is
disabled. The SD card slot also does not work.
For video, coreboot will need to run the OPROM to set this up.
With this board, bare support (running without coreboot) is not available
as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has a legacy GPIO block in the legacy bridge (D0:F31),
which is just the same one found in other x86 chipset. Since we
programmed the GPIO register block base address, we should be
able to enable the GPIO support on Intel Galileo board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have added Quark MRC codes, call MRC in dram_init() so
that DRAM can be initialized on a Quark based board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
New board/intel/galileo board directory with minimum codes, plus
board dts, defconfig and configuration files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.
This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).
Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Correct the SPI flash compatible string, add an alias and specify the
position of the MRC cache, used to store SDRAM training settings for the
Memory Reference Code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link
which is currently the only real board officially supported to run
U-Boot loaded by coreboot.
Note the symbolic link file chromebook_link.dts is deleted and
link.dts is renamed to chromebook_link.dts.
To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86
define needs to be moved to arch/x86/cpu/ivybridge/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present the normal update (which happens much later) does not work. This
seems to have something to do with the 'no eviction' mode in the CAR, or at
least moving the microcode update after that causes it not to work.
For now, do an update early on so that it definitely works. Also refuse to
continue unless the microcode update check (later in boot) is successful.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Topcliff PCH has 4 UART devices integrated (Device 10, Funciton
1/2/3/4). Add the corresponding device nodes in the crownbay.dts per
Open Firmware PCI bus bindings.
Also a comment block is added for the 'stdout-path' property in the
chosen node, mentioning that by default the legacy superio serial
port (io addr 0x3f8) is still used on Crown Bay as the console port.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use ePAPR defined properties for x86-uart: clock-frequency and
current-speed. Assign the value of clock-frequency in device tree
to plat->clock of x86-uart instead of using hardcoded number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commits cleans up the board dts files.
- Correct the serial port register size to 8
- Remove the misleading status = "disabled" statement in the
serial.dtsi
- Move the inclusion of skeleton.dtsi from serial.dtsi to board
dts files
- Let the board dts file define stdout-path in the chosen node
- Remove device nodes in board dts files thar are duplicated to
skeleton.dtsi
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The name of coreboot.dtsi is misleading, as it actually describes
the legacy serial port device node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
To avoid having two microcode formats, adjust the build system to support
obtaining the microcode from the device tree, even in the case where it
must be made available before the device tree can be accessed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Integrate the processor microcode version 1.05 for Tunnel Creek,
CPUID device 20661h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are new microcode revisions available. Update them. Also change
the format so that the first 48 bytes are not omitted from the device tree
data.
Signed-off-by: Simon Glass <sjg@chromium.org>
We might end up with a few of these, so put them in their own directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng
Simon Glass
Gabriel Huau