This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Using NAKs on empty RX fifo for bulk in transfers is the right choice
for a interrupt driven model, but U-Boot uses polling and expects an
immediate answer if there is no incoming packet. Using ZLP Bulk In Response
(BIR) mode avoids unexpected timeouts in the host controller driver.
As ZLP mode is reset default, there is no need to set it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If Option 52 in the vendor option field signals overloading
of the file and/or sname fields, these field may contain
additional options. Formatting of file/sname contained options
is the same as in the vendor options field, but without the
leading magic.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If 'file' is overloaded, it is wrong to get or put the bootfile name
from it/to it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As we don't modify the 'name' parameter, so change it to const.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The loop should check all ethenet devices, not only the first device,
to set each specified ethaddr, or it'll cause failure when we use other
devices.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
smsc95xx_recv() does not reassemble bursts spread over multiple URBs.
If there is a lot of broadcast traffic, the fifo will fill up to the
burst cap limit. Lowering the burst cap to the URB size ensures no packet
spans multiple urbs.
Caveat, lower limit for working burst cap is 5/33 HS/FS packets.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Timeout handler should be stopped after reception of DHCPACK. If "autoload"
is not set, the handler is immediately replaced by the TFTP handler,
otherwise it may trigger before the next boot stage begins.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
eth_rx() in the main reception loop may trigger sending a packet which
is already timed out (or will immediately) upon reception of an ARP reply.
As long as the ARP reply is pending, the timeout handler of a packet
should be postponed.
Happens on TFTP with bad network (e.g. WLAN).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net_start_again() will be called from net_loop() if state is NETLOOP_FAIL.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pad has no len byte, so the normal parsing code fails.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
RFC1542, 3.2:
"The 'secs' field of a BOOTREQUEST message SHOULD represent the
elapsed time, in seconds, since the client sent its first BOOTREQUEST
message. Note that this implies that the 'secs' field of the first
BOOTREQUEST message SHOULD be set to zero."
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename check_packet to check_reply_packet to make its function more
obvious.
The check for DHCP_* values is completely off, as it should
compare against DHCP option 53 (Message Type). Only valid value for
any Bootp/DHCP reply is BOOTREPLY.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the error when STATUS_LED_BOOT is not defined.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If CONFIG_CMD_DHCP is enabled, the vci (vendor-class-identifier) string
isn't inserted into the bootp-packet during SPL stage because the
CONFIG_BOOTP_VCI_STRING
instead
CONFIG_SPL_NET_VCI_STRING
We fix this with testing for CONFIG_SPL_BUILD and testing for existing
CONFIG_SPL_NET_VCI_STRING.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TFTP source and destination port variable names are
'tftpsrcp' and 'tftpdstp' in the code, but 'tftpsrcport'
and 'tftpdstport' in the README file. Fix the README.
Add environment variable 'tftptimeoutcountmax'. As per the
comments about the global variable tftp_timeout_count_max,
make sure tftptimeoutcountmax is nonnegative.
Introduce configuration option CONFIG_NET_TFTP_VARS,
which controls whether environment variables tftpblocksize,
tftptimeout, and tftptimoueoutcountmax are read by the TFTP
client code. CONFIG_NET_TFTP_VARS defaults to y but can be
set to n by targets with to tight size contraints.
Make bf527-ezkit set CONFIG_NET_TFTP_VARS to n to keep the
target size below limit.
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This reverts commit 321f86e18d.
The original bug has been fixed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-on: Zedboard and ZC706 board
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-on: zc702
Tested-by: Michal Simek <michal.simek@xilinx.com>
We should not init the console this early since it precludes using driver
model for the UART, since it is not set up at the start of board_init_f().
See the README for more information. The debug UART does not have this
restriction. If we want to do early init with the console on it can be done
in spl_board_init().
Move the preloader_console_init() call from board_init_f() to board_init_r().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
This C function should be used to do the early memory layout and init. This
is beyond my powers, so just add a TODO for the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Tested on LS2085ARDB and LS2085AQDS (armv8 SoC).
Tested-by: York Sun <yorksun@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Change the #ifdef so that the early malloc() area is not set up in SPL if
CONFIG_SYS_SPL_MALLOC_START is defined. In that case it would never actually
be used, and just chews up stack space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This function will be used by both SPL and U-Boot proper. So move it into
a common place. Also change the #ifdef so that the early malloc() area is
not set up in SPL if CONFIG_SYS_SPL_MALLOC_START is defined. In that case
it would never actually be used, and just chews up stack space.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the following snippet:
if [ ! -x `which $prereq` ]; then
When $prereq does not exist, `which $prereq` evaluates to the empty string,
which results in *no* argument being passed to the -x operator, which then
evaluates to true, which is the equivalent of the prereq having been found. In
order for this to fail as expected, we must pass an empty argument, which then
causes -x to fail. Do this by wrapping the `` in quotes so there's always an
argument to -x, even if the value of the argument is zero-length.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
In my patch series to replace fs/fat with "ff.c", I enhanced ff.c to
optimize file reading, so that reads of contiguous clusters are submitted
to the IO device as a single read. This test attempts to torture-test
edge-cases of that enhancement.
BTW, the only way I found to validate that this script actually does
create non-contiguous files was to manually inspect the FAT bitmap in a
hex dump of the FAT image. hdparm --fibmap doesn't work on loop-mounted
filesystems. filefrag -v -e seems to lie about files being contiguous
when they aren't.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
itest accesses memory, and hence must map/unmap it. Without doing so, it
accesses invalid addresses and crashes.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Under the assumptions of having a UBI volume called boot, containing
a ubifs filesystem.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add generic fs support, so that commands like ls, load and test -e can be
used on ubifs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Implement the necessary functions for implementing generic fs support
for ubifs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Modify the ubifs u-boot wrapper function prototypes for generic fs use,
and give them their own header file.
This is a preparation patch for adding ubifs support to the generic fs
code from fs/fs.c.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is not necessary / useful when not building with CONFIG_SANDBOX and
with the addition of ubifs support to the generic fs commands it actually
gets in the way, since both operate on a fake / NULL blkdev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
In the "Getting Started with Coccinelle - KVM edition" presentation that
has been held by Julia Lawall at the KVM forum 2015 (see the slides at
http://events.linuxfoundation.org/sites/events/files/slides/tutorial_kvm_0.pdf),
she pointed out some bad return value checks in U-Boot that can be
detected with Coccinelle by using the following config file:
@@
identifier x,y;
identifier f;
statement S;
@@
x = f(...);
(
if (x < 0) S
|
if (
- y
+ x
< 0) S
)
This patch now fixes these issues.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support and enable it to set
'board_rev' and 'board_name' envs.
'board_rev' can be used in scripts to determine what board we are running on
and 'board_name' for pretty printing.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
For current U-Boot to initialize status LEDs via status_led_init(), it
is required to have both CONFIG_STATUS_LED and STATUS_LED_BOOT defined.
This may be a particular concern with GPIO LEDs, where __led_init() is
required to correctly set up the GPIO (gpio_request and
gpio_direction_output). Without STATUS_LED_BOOT the initialization isn't
called, which could leave the user with a non-functional "led" command -
due to the fact that the LED routines in gpio_led.c use gpio_set_value()
just fine, but the GPIO never got set up properly in the first place.
I think having CONFIG_STATUS_LED is sufficient to justify a
corresponding call to status_led_init(), even with no STATUS_LED_BOOT
defined. To do so, common/board_r.c needs call that routine, so it now
is exposed via status_led.h.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
[trini: Add dummy __led_init to pca9551_led.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
For boards that support LEDs driven via GPIO (CONFIG_GPIO_LED),
it may be useful to have some generic stubs (wrapper functions)
for the "colored" LEDs.
This allows defining STATUS_LED_* values directly to GPIO numbers,
e.g.: #define STATUS_LED_GREEN 248 /* = PH24 */
To keep those optional, it's probably best to introduce an additional
configuration setting. I've chosen CONFIG_GPIO_LED_STUBS for that.
Placing the code in drivers/misc/gpio_led.c also ensures that it
automatically depends on CONFIG_GPIO_LED too.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the virtual address and physical address mapping of nios2 with
MMU are different. Add a check of MMU, and fix the mapping.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Ley Foon Tan <lftan@altera.com>
Convert cache flush to use dm cpu data.
The original cache flush functions are written in assembly
and use CONFIG_SYS_{I,D}CACHE_SIZE... macros. It is difficult
to convert to use cache configuration in dm cpu data which is
extracted from device tree.
The cacheflush.c of Linux nios2 arch uses cpuinfo structure,
which is very close to our dm cpu data. So we copy and modify
it to arch/nios2/lib/cache.c to replace the old cache.S.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Set default icache and dcache configuration for start.S.
We want to remove the CONFIG_SYS_{I,D}CACHE_SIZE...
configuration macros. As we are just barely starting from
reset, there is no luxury of device tree.
We will set some maximum cache configuration so that it will
work for most configurations. This is used only in this
start.S. The speed penalty is only once here.
After start up, during board initialization, cpu information
will be extracted from device tree. Then cache flush operations
will have correct cache configurations.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Sylvain Lemieux
Stefan Brüns
Josh Wu
Gong Qianyu
Thomas Chou
Hannes Petermaier
Albert ARIBAUD \(3ADEV\)
Masahiro Yamada
Simon Glass
Stephen Warren
Roy Spliet
Hans de Goede
Pierre Aubert
Thomas Huth
Guillaume GARDET
Bernhard Nortmann
Lokesh Vutla