Commit graph

38891 commits

Author SHA1 Message Date
Wenbin Song
6ffc490541 armv8: ls1043a: enable pxe commands
Enable pxe command for ls1043ardb and ls1043aqds.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:46:07 -07:00
Prabhakar Kushwaha
37eac3f460 armv8: ls1012a: Update Refresh cycle for DDR
Refresh cycle value must be selected based on the frequency
of DDR. tREFI = 7.8 us as per JEDEC. The value for MDREF[REF_CNT]
should be based on round up (tREFI/tCK) formula. For 500MHz, mdref
value should be 0x0f3c8000.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:46:02 -07:00
Prabhakar Kushwaha
9c3fca2a79 armv8: ls1012a: Enable DDR row-bank-column decoding
Enable DDR row-bank-column decoding to decode DDR address as
row-bank-column instead of bank-row-column for improving
performance of serial data transfers.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:56 -07:00
Prabhakar Kushwaha
3b4dbd37dc board: ls1012aqds: Update LBMAP_MASK and RST_CTL_RESET
qixis_reset altbank usagge ~QIXIS_LBMAP_MASK in code. So define
inverse value QIXIS_LBMAP_MASK.

Also, update QIXIS_RST_CTL_RESET value to keep RST_CTL[REQ_MOD]
as 0b11 i.e. PORESET during qixis_reset

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:48 -07:00
Sumit Garg
7fe1d6a410 crypto/fsl: Update blob cmd to accept 64bit addresses
Update blob cmd to accept 64bit source, key modifier and destination
addresses. Also correct output result print format for fsl specific
implementation of blob cmd.

Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:39 -07:00
Yunhui Cui
04e5c6d9cc driver: spi: fsl-qspi: remove compile Warnings
Warnins log:
drivers/spi/fsl_qspi.c: In function ‘qspi_ahb_read’:
drivers/spi/fsl_qspi.c:400:16: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  memcpy(rxbuf, (u8 *)(priv->cur_amba_base + priv->sf_addr), len);

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-08-02 09:45:13 -07:00
York Sun
f3dbf1f0c9 powerpc/mpc85xx: Update erratum workaround for A006379
Update erratum workaround for A006379 to set register CPCHDBCR0
with value 0x001e0000, replacing the old value 0x003c0000.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Dave Liu <dave.liu@nxp.com>
2016-08-02 09:43:13 -07:00
Tom Rini
26fb8db0f4 Merge git://git.denx.de/u-boot-rockchip 2016-07-31 20:31:13 -04:00
Hans de Goede
fcada3b05e sunxi: Re-enable h3 emac support
With the recent bug fixes for the sun8i_emac driver all known issues
are resolved, so we can re-enable the driver.

While at it, also enable the emac on the Orange Pi One.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Jagan Teki <jteki@openedev.com>
2016-07-31 21:45:47 +02:00
Hans de Goede
4069437dfb net: sun8i_emac: Fix DMA alignment issues with the rx / tx buffers
This fixes the following CACHE warnings when using sun8i_emac:

=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [7bf594a8, 7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [7bf59c90, 7bf59e10]
CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)

Note this commit also changes the max rx size from 2024 to 2044,
matching what the kernel driver uses.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31 21:45:46 +02:00
Hans de Goede
3f8ea3b06e sunxi: On newer SoCs use words 1-3 instead of just word 3 from the SID
It seems that bytes 13-14 of the SID / bytes 1-2 from word 3 of the SID
are always 0 on H3 making it a poor candidate to use as source for the
serialnr / mac-address, and the other non constant words (1 and 2) also
have quite a few bits which are the same for some boards,

This commits switches to using the crc32 of words 1 - 3 to get a
more unique value for the mac-address / serialnr.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31 21:45:39 +02:00
Hans de Goede
97322c3e07 sunxi: Ensure that the NIC specific bytes of the mac are not all 0
On 2 of my H3 boards bytes 13-15 of the SID are all 0 leading to
the NIC specific bytes of the mac all being 0, which leads to the
boards not getting an ipv6 address from the dhcp server.

This commits adds a check to ensure this does not happen.

Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2016-07-31 21:45:34 +02:00
Chen-Yu Tsai
3e5e274aed sunxi: Hummingbird_A31_defconfig: Drop MACPWR option
MACPWR was used to bring the Ethernet PHY out of reset. The designware
driver now supports the phy reset gpio binding, so this is no longer
needed. In fact in requesting the same GPIO, it makes the designware
driver fail to probe.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-31 21:45:12 +02:00
Chen-Yu Tsai
4694dc56e9 sunxi: gpio: Add .xlate function for gpio phandle resolution
sunxi uses a 2 cell phandle for gpio bindings. Also there are no
seperate nodes for each pin bank.

Add a custom .xlate function to map gpio phandles to the correct
pin bank device. This fixes gpio_request_by_name usage.

Fixes: 7aa9748584 ("dm: sunxi: Modify the GPIO driver to support driver
		      model")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-07-31 21:45:12 +02:00
jk.kernel@gmail.com
dd63fbc70a rockchip: add support for rk3288 PopMetal board
PopMetal is a rockchip rk3288 based board made by ChipSpark, which has
many interface such as HDMI, VGA, USB, micro-SD card, WiFi, Audio and
Gigabit Ethernet.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
d7ca67b7cd rockchip: add basic support for fennec-rk3288 board
Fennec is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio and WiFi and Gigabit Ethernet. It also includes
on-board 8GB eMMC and 2GB of SDRAM. Expansion connectors provides access
to display pins, I2C, SPI, UART and GPIOs.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
cba6bb1b74 rockchip: rk3288: move evb board to rockchip folder
The 'evb-rk3288' is not a vendor name, change it to 'rockchip' which is
the real vendor name.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
f75711aae7 rockchip: rk3288: revise CONFIG_FASTBOOT_BUF_ADDR
CONFIG_SYS_LOAD_ADDR is absolutely safe to store image for
fastboot.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
77337c1c7a rockchip: remove the duplicated macro config
CONFIG_DOS_PARTITION and CONFIG_EFI_PARTITION are already included in
config_distro_defaults.h, and we don't need them in SPL stage.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
1743d0bafc rockchip: rk3288: disable fastboot in SPL stage
Reduce compilation time for SPL.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
5051a77b2d Revert "rockchip: Move the MMC setup check earlier"
Boot Rom wouldn't initialize sdmmc while booting from eMMC. We need to
setup sdmmc gpio, otherwise we will hit an error below:

=>mmc info
blk_get_device: if_type=6, devnum=0: dwmmc@ff0c0000.blk, 6, 0
uclass_find_device_by_seq: 0 -1
uclass_find_device_by_seq: 0 0
   - -1 -1
   - -1 0
   - found
uclass_find_device_by_seq: 0 1
   - -1 -1
   - -1 0
   - not found
fdtdec_get_int_array: interrupts
get_prop_check_min_len: interrupts
Buswidth = 1, clock: 0
Buswidth = 1, clock: 400000
Sending CMD0
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy
dwmci_send_cmd: Timeout on data busy

This reverts commit 6efeeea79c.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
194a241a6e cosmetic: rockchip: rk3288: pinctrl: fix config symbol naming
Revise config to CONFIG_ROCKCHIP_RK3288_PINCTRL.

Signed-off-by: Ziyuan Xu <jk.kernel@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
2016-07-31 07:24:20 -06:00
jk.kernel@gmail.com
8a632ac135 rockchip: add a dummy byte for the sdram-channel property
Add an extra byte so that this data is not byteswapped.

Signed-off-by: Ziyuan Xu <jk.kernel@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
2016-07-31 07:24:20 -06:00
John Keeping
2b51784aef rockchip: rk3288: Fix pinctrl for GPIO bank 0
Bank 0 is the "PMU GPIO" bank which is controlled by the PMU registers
rather than the GRF registers.  In the GRF the top half of the register
is used as a mask so that some bits can be updated without affecting the
others, but in the PMU this feature is not provided and the top half of
the register is reserved.

Take the same approach as the Linux driver to update the value via
read-modify-write but setting the mask for only the bits that have
changed.  The PMU registers ignore the top 16 bits so this works for
both GRF and PMU iomux registers.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2016-07-31 07:24:20 -06:00
Kever Yang
633fdab0cb rk3399: Reserve space for ARM Trust Firmware
RK3399 needs reserve 0x200000 at the beginning of DRAM, for ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
Xu Ziyuan
b357a7f752 rockchip: rk3036: update MAINTAINER file
Update MAINTAINER files for kylin_rk3036, evb_rk3036.

Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
Kever Yang
22948e1015 configs: rockchip: remove no use MACRO
The CONFIG_ROCKCHIP_COMMON and CONFIG_SPL_ROCKCHIP_COMMON are no use now,
remove them.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-07-31 07:24:20 -06:00
Kever Yang
46683f3da1 mmc-uclass: correct the device number
Not like the mmc-legacy which the devnum starts from 1, it starts from 0
in mmc-uclass, so the device number should be (devnum + 1) in get_mmc_num().

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-07-31 07:24:20 -06:00
Angelo Dureghello
5c928d0204 m68k: code reformatting for all start.S files
This patch is style-related only, to reformat all the start.S code,
actually not following a coherent style inside single files and
between different cpu start.S files.

Linux format has been respected, as
  - max line width at 80 columns
  - one 8 cols tab between asm instructions and operands
  - inline comments, where any, fixed at col 41

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2016-07-30 22:59:18 +02:00
Vignesh R
08887ed450 ARM: am57xx_evm: Enable QSPI support
AM571x IDK and AM572x IDK EVMs have spansion s25fl256s QSPI flash on the
board connected to TI QSPI IP over CS0. Therefore enable QSPI support.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:07 +05:30
Vignesh R
9af6ce4248 ARM: dts: am57xx-idk-common: Enable support for QSPI
AM571x and AM572x IDK have a spansion s25fl256s QSPI flash on the board
connected to TI QSPI over CS0. Hence, add QSPI and flash slave
DT nodes.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Vignesh R
2ae9422145 configs: am43xx_evm_defconfig: Enable CONFIG_SPI_FLASH_BAR
AM437x SK and AM437x IDK EVMs have 64MB flash, therefore enable
CONFIG_SPI_FLASH_BAR to access flash regions above 16MB.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Vignesh R
70ebdd775b ARM: dts: dra7xx: Update spi-max-frequency for QSPI
According to AM572x DM SPRS953A, QSPI max bus speed is 76.8MHz.
Therefore update the spi-max-frequency value of QSPI node for DRA74 and
DRA72 evm. This increase flash read speed by ~2MB/s.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
b9612bb2de configs: dra7xx: Update QSPI speed to 76.8MHz
Now that QSPI driver can support 76.8MHz, update the
CONFIG_SF_DEFAULT_SPEED to the same value.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
a6f56ad1ee spi: ti_qspi: dra7xx: Add support to use 76.8MHz clock
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, update
the driver to use the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Lokesh Vutla
4d790788ce ARM: dra7xx: Change DPLL_PER_HS13 divider value
According to AM572x DM SPRS953A, QSPI bus speed can be 76.8MHz, hence
update QSPI input clock divider value (DPLL_PER_HS13) to provide 76.8MHz
clock, so that driver can use the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Wenyou Yang
b302669f46 sf: sf_params: Add AT25DF321 flash support
Add AT25DF321 flash support.
Fix AT25DF321A device name.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Vignesh R
fee3b6af90 spi: ti_qspi: Remove delay in read path for dra7xx
As per commit b545a98f5d ("spi: ti_qspi: Add delay
for successful bulk erase) says its added to meet bulk erase timing
constraints. But bulk erase is a cmd to flash and delay in read path
does not make sense. Morever, testing on DRA74/DRA72 evm has shown that
this delay is no longer required.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
c595a28530 spi: ti_qspi: Fix compiler warning when DEBUG macro is set
clk_div is uninitialized at the beginning of ti_spi_set_speed(), move
debug() print after clk_div calculation to avoid compiler warning and to
have proper value of clk_div printed during debugging.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Vignesh R
69eeefaa06 spi: ti_qspi: Fix failure on multiple READ_ID cmd
Populating QSPI_RD_SNGL bit(0x1) in priv->cmd means that value
QSPI_INVAL (0x4) is not written to CMD field of QSPI_SPI_CMD_REG in
ti_qspi_cs_deactivate(). Therefore CS is never deactivated between
successive READ ID which results in sf probe to fail.
Fix this by not populating priv->cmd with QSPI_RD_SNGL and OR it wih
priv->cmd as required (similar to the convention followed in the
driver).

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
2016-07-30 00:15:00 +05:30
Moritz Fischer
6bde34f1ae spi: Add support for N25Q016A
This commit adds support in the spi-nor driver for the
N25Q016A, a 16Mbit SPI NOR flash from Micron.

Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-07-30 00:15:00 +05:30
Tom Rini
4711e7f7af Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-07-28 08:45:00 -04:00
Fabio Estevam
77cbd3a141 MAINTAINERS: i.MX: Add board/freescale/*mx* path
Pass the board/freescale/*mx*/ path as files maintained by Stefano
Babic.

While this is not ideal and does not cover all the i.MX board cases,
it gives at least a better hint for the /scripts/get_maintainer.pl
tool.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-28 13:27:22 +02:00
Fabio Estevam
4c97077ce7 mx7dsabresd: MAINTAINERS: Add mx7dsabresd_secure_defconfig
Add an entry for the mx7dsabresd_secure_defconfig target.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-28 13:27:21 +02:00
Stefan Agner
7626ba488e mx7_common: initialize generic timer on all CPU's
Use CONFIG_TIMER_CLK_FREQ to let the non-secure init code initialize
the generic timer on all CPU's. This allows to make use of the timer
freuquency register also on other CPU than the start CPU which is
important for KVM.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2016-07-28 13:27:21 +02:00
Diego Dorta
ec1935a243 mx6ul_14x14_evk: Remove unused define
Remove unused define constant.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-28 13:27:21 +02:00
Fabio Estevam
63326e6f0b cgtqmx6eval: Remove uneeded PHYS_SDRAM_SIZE
cgtqmx6eval uses the imx_ddr_size() function to calculate the DDR size in
runtime, so there is no need to define PHYS_SDRAM_SIZE.

Remove the unneeded definition.

Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2016-07-28 13:27:21 +02:00
Fabio Estevam
10ced52242 novena: Remove uneeded PHYS_SDRAM_SIZE
novena uses the imx_ddr_size() function to calculate the DDR size in
runtime, so there is no need to define PHYS_SDRAM_SIZE.

Remove the unneeded definition.

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
2016-07-28 13:27:21 +02:00
Fabio Estevam
c6a51bab17 bx50v3: Use imx_ddr_size() for calculating the DDR size
imx_ddr_size() can be used to calculate the DDR size in runtime.

By using this function we no longer need to define PHYS_SDRAM_SIZE.

Cc: Martin Donnelly <martin.donnelly@ge.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-07-28 13:27:20 +02:00
Fabio Estevam
84c51687a7 aristainetos: Use imx_ddr_size() for calculating the DDR size
imx_ddr_size() can be used to calculate the DDR size in runtime.

By using this function we no longer need to define PHYS_SDRAM_SIZE.

Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
2016-07-28 13:27:20 +02:00