Earlier, architecture specific init code was mixed with board initialization
code in board/spear/... This patch updates architecture support for SPEAr in
latest u-boot and prints the SoC information.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The
driver for this device is already supported by u-boot, so configuring
board configuration file and defining base addresses etc to make use
of the common driver
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Xloader table was used primarily to inform u-boot about the DDR size. However,
now the ddr size is calculated at runtime which eliminates any need for the
Xloader table. So removing this unnecessary code.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since FSMC is a standard IP and it supports different memory interfaces, it
is supported independent of spear platform and spear is configured to use that
driver for interfacing with the NAND device
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
save_boot_params_default() in cpu.c accesses uninitialized stack area
when it compiled with -O0 (not optimized).
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Tom Rini <trini@ti.com>
USB clocks will be required for fastboot, tftp
related functionalities. Move these clocks to
essential group inorder to have the functionality
working when non-essential clocks are not enabled.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
GPMC clocks are currently getting enabled as a part
non-essential clocks. This will be required during
NOR boot. Move this to essential group to keep the
functionality, when non-essential clocks are not
enabled.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The external phy is present in the case OMAP5 soc is currently
configured in emif-common.c. This results in having dummy structures
for those Socs which do not have a external phy. So by having a weak
function in emif-common and overriding it in OMAP5, avoids the use
of dummy structures.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
This reduced M,N couple corresponds to the advised value from
TI HW team.
Tested on 4460 Pandaboard, it also provides peripheral clocks
closer to the advised values.
Signed-off-by: Sebastien Jan <s-jan@ti.com>
The PLL setup values currently assume a 24 Mhz input clock.
This patch uses V_OSCK from the board config file to support boards
with different input clock rates.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Code currently tests for <= 0xff. Micron manufacturer code is 0xff, so
Micron memory will not be detected!
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Some rams (Micron for example) return duplicate mr data on all byte lanes.
Users of the get_mr function currently don't deal with this duplicated
data gracefully. This patch detects the duplicated data and returns only
the expected 8 bit mr data.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Errata ID:i727
Description: The refresh rate is programmed in the EMIF_SDRAM_REF_CTRL[15:0]
REG_REFRESH_RATE parameter taking into account frequency of the device.
When a warm reset is applied on the system, the OMAP processor restarts
with another OPP and so frequency is not the same. Due to this frequency
change, the refresh rate will be too low and could result in an unexpected
behavior on the memory side.
Workaround:
The workaround is to force self-refresh when coming back from the warm reset
with the following sequence:
• Set EMIF_PWR_MGMT_CTRL[10:8] REG_LP_MODE to 0x2
• Set EMIF_PWR_MGMT_CTRL[7:4] REG_SR_TIM to 0x0
• Do a dummy read (loads automatically new value of sr_tim)
This will reduce the risk of memory content corruption, but memory content
can't be guaranteed after a warm reset.
This errata is impacted on
OMAP4430: 1.0, 2.0, 2.1, 2.2, 2.3
OMAP4460: 1.0, 1.1
OMAP4470: 1.0
OMAP5430: 1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
EMIF and DDR device state are preserved in warmreset. Redoing the full
initialisation would cause unexpected behaviour. Do only partial
initialisation to account for frequency change.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Certain modules are not affected by means of
a warm reset and need not be configured again.
Adding an API to detect the reset reason warm/cold.
This will be used to skip the module configurations
that are retained across a warm reset.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Interrupts and exceptions doesn't work in relocated code.
It badly use IRQ_STACK_START_IN in rom area as interrupt stack.
It is because the vecotr table is not moved to ram area.
This patch moves vector table before jumping relocated code.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Tested-by: Tom Rini <trini@ti.com>
So that they can be redefined by some boards specific values.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
These two function nows ensure that the MPP is configured correctly for
the SPI controller before any SPI access, and restore the initial
configuration when the access is over.
Since the used pins for the SPI controller can differ (2 possibilities
for each signal), the used pins are configured with CONFIG_SYS_KW_SPI_MPP.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
If a second non NULL argument is given to the kirkwood_mpp_conf
function, it will be used to store the current configuration of the MPP
registers. mpp_save must be a preallocated table of the same size as
mpp_list and it must be zero terminated as well.
A later call to kirkwood_mpp_conf function with this saved list as first
(mpp_conf) argment will set the configuration back.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Enable new PIO feature supported by Atmel SoC.
Using CPU_HAS_PIO3 micro to enable PIO new feature.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The commit "i.mx: fsl_esdhc: add the i.mx6q support" (4692708d) introduces
support for the i.MX6Q MMC host controller USDHC.
MXC_IPG_PERCLK sets the clock to 66MHz. This seems to be the default clock
of the ESDHC IP found in < i.MX6 silicon. However, the default clock for the USDHC
IP found in i.MX6 is 200MHz (MXC_ESDHC_CLK). This difference will cause a 3 times
higher clock on SD_CLK than expected (see fsl_esdh.c -> set_sysctl()).
Signed-off-by: Michael Langer <michael.langer@de.bosch.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <r64343@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This function can be overridden at run-time and allows implementors
of new boards based on the i.MX28 chip to fine-tune the memory params.
It is possible to write into the dram_vals array because when the SPL
runs, it is located SRAM. Therefore the location is writable. There is
no possibility of these data to be read-only.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
The macro mistakenly referred to 32bit struct instead of 8bit one.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
SATA_ALT_REF_CLK field corresponds to bits 1 and 2 of offset 0x180c.
Fix the mask for these bits.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
If one PAD does not have mux or pad config register, we need
set the NO_MUX_I/NO_PAD_I to 0, the old value is not correct
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch performs the pinmux configuration in a common file.
As of now only EXYNOS5 pinmux for SDMMC, UART and Ethernet is
supported.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since Exynos architecture have new SoCs,
need to fix cpuinfo correctly.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Chander Kashyap <chander.kashyap@linaro.org>
To meet certain timing requirements on the lpddr2 cmd and data phy
interfaces ,lpddr iopads have to be configured as differential buffers
and a Vref has to be internally generated and provided to these buffers.
Correcting the above settings here.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
In OMAP5432 EMIF controlller supports DDR3 device.
This patch adds support for ddr3 device intialization and configuration.
Initialization sequence is done as specified in JEDEC specs.
This also adds support for ddr3 leveling.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Previously, only the low 5 bits (NCH) were being transfered
from DDRVTPR to DDRVTPIOCR, the bits 5-9 where zeroed.
VTP_RECAL should be bit 15, not 18.
The only mainline board affected by this change is davinci_sonata.
The other Davinci boards define CONFIG_SKIP_LOWLEVEL_INIT.
However, if the program that loads u-boot on these boards
copied the code from u-boot, they will need fixed as well.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Please get tested by acks before applying, where tested by
means an overnight memory test.
Thanks
Troy
get_ram_size checks the given memory range for valid ram,
but expects the size of memory to be aligned to the power
of 2. In case of OMAP5 evm board the memory available is
2GB - 16MB(used for TRAP section) = 2032MB.
So always ensure that the size of memory used for testing is
aligned to the power of 2.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The unmapped entries in tiler space are set with
values 0xFF. So creating a DMM section of
size 16MB at 0xFF000000 with ADDRSPACE set to 0x2.
This way all the unmapped entry accesses to tiler
will be trapped by the EMIF and a error response
is sent to the L3 interconnect. L3 errors are
inturn reported to MPU.
Note that here the tiler trap section is overlapping
with the actual ddr physical space and we lose 16MB
out of the total 2GB.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DMM sections can be overlapping with each other, with
sections 3 to 0 having the highest to lowest priority in that
order. There could also be a section that is used trap the
unmapped Tiler entries and this trap section could be
overlapping with the actual sdram area.
So take care of the above scenarios while calculating the
size of the actual ram.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Walk the BIT and BCT to find the ODMDATA word in the
CustomerData field and put it into Scratch20 reg for
use by kernel, etc.
Built all Tegra builds OK; Booted on Seaboard and saw
ODMDATA in PMC scratch20 was the same as the value in my
burn-u-boot.sh file (0x300D8011). NOTE: All flash utilities
will have to specify the odmdata (nvflash --odmdata n) on
the command line or via a cfg file, or built in to their
BCT.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Override -march setting for tegra to -march=armv4t for files that are
necessary for low level init on tegra.
The recent change to use -march=armv7-a for armv7 caused a regression
on tegra because tegra starts boot on a arm7tdmi processor before
transferring control to the cortex-a9. While still executing on the
arm7tdmi there are calls to getenv_ulong() and memset() that cause an
illegal instruction exception if compiled for armv7.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Correct this warning seen by Albert:
ap20.c:44:18: warning: array subscript is above array bounds
There is a subtle bug here which currently causes no errors, but might
in future if people use PCI or the 32KHz clock. So take the opportunity
to correct the logic now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is based on top of:
tegra: add alternate UART1 funcmux entry
tegra: add UART1 on GPU funcmux entry
v2: remove enum change
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Tom Warren <twarren@nvidia.com>
CC: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(In at least some configurations) Whistler uses UART1 on pingroups
UAA, UAB.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.
Signed-off-by: York Sun <yorksun@freescale.com>
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.
Signed-off-by: York Sun <yorksun@freescale.com>
addrmap_phys_to_virt() converts a physical address (phys_addr_t) to a
virtual address, so it should return a pointer instead of an unsigned long.
Its counterpart, addrmap_virt_to_phys(), takes a pointer, so now they're
orthogonal.
The only caller of addrmap_phys_to_virt() converts the return value to
a pointer anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
During NAND_SPL boot, base address and different register are programmed
default by corresponding NAND controllers(eLBC/IFC). These settings are
sufficient enough for NAND SPL.
Avoid updating these register.They will be programmed during NAND RAMBOOT.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG).
So define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be
used during boot to work around the limitations.
Please refer doc/README.mpc85xx for more information
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Update NAND code base to ovecome e500 and e500v2's second limitation i.e. IVPR
+ IVOR15 should be valid fetchable OP code address.
As NAND SPL does not compile vector table so making sure IVOR + IVOR15 points to
any fetchable valid data
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires debug exception vecter (IVPR +
IVOR15) to have valid and fetchable OP code.
1) While executing in translated space (AS=1), whenever a debug exception is
generated, the MSR[DS/IS] gets cleared i.e. AS=0 and the processor tries to
fetch an instruction from the debug exception vector (IVPR + IVOR15); since now
we are in AS=0, the application needs to ensure the proper TLB configuration to
have (IVOR + IVOR15) accessible from AS=0 also.
Create a temporary TLB in AS0 to make sure debug exception verctor is
accessible on debug exception.
2) Just after relocation in DDR, Make sure IVPR + IVOR15 points to valid opcode
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register
Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.
Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- BSC9131 is integrated device that targets Femto base station market.
It combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
- BSC9130 is exactly same as BSC9131 except that the max e500v2
core and DSP core frequencies are 800M(these are 1G in case of 9131).
- BSC9231 is similar to BSC9131 except no MAPLE
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte shared
L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding,
Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing,
and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion
operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with
ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network acceleration
including IEEE 1588. v2 hardware support and virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single port)
and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
This patch takes care of code pertaining to power side functionality only.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
The misspelling of "semiconductor" causes some internal copyright analysis
tools to complain.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We provide a default table of { 9600, 19200, 38400, 57600, 115200 }
in <config_fallbacks.h> which mkconfig places after <configs/...h> in
the generated config file. This is used when a board has not set its
own table.
Signed-off-by: Tom Rini <trini@ti.com>
* 'master' of git://git.denx.de/u-boot-video:
video: atmel/lcd: add LCD driver for new Atmel SoC
video: cfb_console: flush dcache for frame buffer in DRAM
cfb_console: Ignore bell character
cfb_console: Add console_clear_line function
cfb_console: Fix function console_back
omap3_dss: cosmetic changes
omap3_dss: add optional framebuffer
mx53loco: Add LCD support
mx5: Rename mx51_fb_init()
mx53: Allow IPUv3 driver to also work on mx53
mx51evk: Add LCD support
EXYNOS: display 32bpp bitmap TIZEN logo
create lib/tizen directory
LCD: display 32bpp decompressed bitmap image
common/lcd.c: reduce one CONFIG_LCD_LOGO ifdef
common/lcd.c: reduce some CONFIG_LCD_*_LOGO ifdefs
common/lcd.c: use ARRAY_SIZE
cmd_bmp.c: make bmp_display() usable by drivers or board code
LCD: support another s6e8ax0 panel type
LCD: change s6e8ax0 panel gamma value
include/video.h: drop unused video_printf()
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-mips:
MIPS: board.c: move extern declarations to u-boot-mips.h
MIPS: bootm_qemu_mips.c: make checkpatch.pl clean
MIPS: bootm.c: make checkpatch.pl clean
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-sh:
sh/ap_sh4a_4a: Fix typo of operator in ET0_ETXD4
sh: Add SH7269 device and RSK2+SH7269 board
sh: Set CONFIG_SH_ETHER_PHY_MODE and CONFIG_SH_ETHER_SH7734_MII to boards with sh_eth
sh: Add support for AP-SH4A-4A board
sh: Add register definition of PFC for SH7734
sh: r0p7734: Add support I2C controller
sh: Add bit control functions
sh: Add support for r0p7734 board
sh: Add support Renesas SH7734
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch conditionally defines flush_dcache_range() and
invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
resulting in the following output:
$ ARCH=powerpc CROSS_COMPILE=powerpc-linux-gnu- ./MAKEALL MPC8572DS
Configuring for MPC8572DS board...
make: *** [u-boot] Error 1
powerpc-linux-gnu-size: './u-boot': No such file
e1000.c: In function ‘e1000_initialize’:
e1000.c:5264:13: warning: assignment from incompatible pointer type [enabled by default]
tsec.c: In function ‘tsec_initialize’:
tsec.c:638:12: warning: assignment from incompatible pointer type [enabled by default]
drivers/usb/host/libusb_host.o: In function `ehci_td_buffer':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:186: undefined reference to `flush_dcache_range'
drivers/usb/host/libusb_host.o: In function `ehci_submit_async':
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:346: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:348: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:349: undefined reference to `flush_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:372: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:374: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:376: undefined reference to `invalidate_dcache_range'
/home/marex/U-Boot/u-boot-imx/drivers/usb/host/ehci-hcd.c:386: undefined reference to `invalidate_dcache_range'
make: *** [u-boot] Error 1
--------------------- SUMMARY ----------------------------
Boards compiled: 1
Boards with errors: 1 ( MPC8572DS )
----------------------------------------------------------
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
This patch fixes following warning:
---8<---
board.c: In function 'board_init_r':
board.c:257: warning: unused variable 's'
--->8---
Patch de30122bb5 missed to remove this variable
too.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.
The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This provide bit control functions as clrbits_*, setbits_* and
clrsetbits_*.
V2: Fix comment style and error of whitespace.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove unnecessary brackets.
Unwrap lines which are below 80 chars.
Single line comment as single line (as the rest).
Moved init values to the source code.
cc: s-paulraj@ti.com
cc: khasim@ti.com
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
The beagle board uses the background color to show an orange screen during
startup. This patch adds the ability to add a frame buffer, with the
intention not to break the beagle board use case (I don't have one).
videomodes.c is not used. Scrolling depends on this patch:
http://patchwork.ozlabs.org/patch/155662/
cc: trini@ti.com
cc: s-paulraj@ti.com
cc: khasim@ti.com
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
s6e8ax0 panel has many panel of types. This patch support another panel
on TIZEN lunchbox board(HWREVISION 2). This panel has reversed panel
display type. So, I had added necessary command.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
These are all the files which use the API incorrectly but did not get
built using MAKEALL -a powerpc|arm. I have no compiler for them, but
the remaining issues should be far less than without this patch.
Any outstanding issues are left to the maintainers of boards that use
these drivers.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_scc.c: In function 'mpc82xx_scc_enet_initialize':
ether_scc.c:377:14: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:453:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
ether_fcc.c: In function 'fec_initialize':
ether_fcc.c:390:15: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
fec.c: In function 'mpc8220_fec_recv':
fec.c:791:9: warning: passing argument 1 of 'NetReceive' discards qualifiers from pointer target type
include/net.h:438:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
fec.c: In function 'mpc8220_fec_initialize':
fec.c:839:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Commit db288a9 "net: Remove volatile from net API" caused a number of
build warnings:
fec.c: In function 'fec_initialize':
fec.c:183:13: warning: assignment from incompatible pointer type [enabled by default]
fec.c: In function 'fec_recv':
fec.c:284:5: warning: passing argument 1 of 'NetReceive' discards 'volatile' qualifier from pointer target type [enabled by default]
/home/wd/git/u-boot/work/include/net.h:433:13: note: expected 'uchar *' but argument is of type 'volatile uchar *'
scc.c: In function 'scc_initialize':
scc.c:85:14: warning: assignment from incompatible pointer type [enabled by default]
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Fix:
npe.c: In function 'npe_initialize':
npe.c:630:13: warning: assignment from incompatible pointer type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-usb:
USB: S5P: Add ehci support
usb:udc:samsung Add functions for storing private gadget data in UDC driver
usb:gadget:composite: Support for composite at gadget.h
usb:gadget:composite USB composite gadget support
usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
USB: Document the QH and qTD antics in EHCI-HCD
USB: Drop cache flush bloat in EHCI-HCD
USB: Drop ehci_alloc/ehci_free in ehci-hcd
USB: Align buffers at cacheline
usb: use noinline define
* 'master' of git://git.denx.de/u-boot-nand-flash:
NAND: Remove ONFI detection message to from bootup log
driver/mtd:IFC: Fix possible memory leak
driver/mtd: IFC NAND: Add support of ONFI NAND flash
mtd, nand: move some printfs to debug output.
nand_util: correct YAFFS image write function
powerpc/85xx: fix NAND boot linker scripts for -fpic
nand: extend .raw accesses to work on multiple pages
* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
omap4: do not enable auxiliary cores
omap4: do not enable fs-usb module
omap4: panda: disable uart2 pads during boot
igep00x0: change mpurate from 500 to auto
igep00x0: enable the use of a plain text file
tegra2: trivially enable 13 mhz crystal frequency
tegra: Enable keyboard for Seaboard
tegra: Switch on console mux and use environment for console
tegra: Add tegra keyboard driver
tegra: fdt: Add keyboard definitions for Seaboard
tegra: fdt: Add keyboard controller definition
tegra: Add keyboard support to funcmux
input: Add support for keyboard matrix decoding from an fdt
input: Add generic keyboard input handler
input: Add linux/input.h for key code support
fdt: Add fdtdec functions to read byte array
tegra: Enable LP0 on Seaboard
tegra: fdt: Add EMC data for Tegra2 Seaboard
tegra: i2c: Add function to find DVC bus
fdt: tegra: Add EMC node to device tree
tegra: Add EMC settings for Seaboard
tegra: Turn off power detect in board init
tegra: Set up warmboot code on Nvidia boards
tegra: Setup PMC scratch info from ap20 setup
tegra: Add warmboot implementation
tegra: Set up PMU for Nvidia boards
tegra: Add PMU to manage power supplies
tegra: Add EMC support for optimal memory timings
tegra: Add header file for APB_MISC register
tegra: Add tegra_get_chip_type() to detect SKU
tegra: Add flow, gp_padctl, fuse, sdram headers
tegra: Add crypto library for warmboot code
tegra: Add functions to access low-level Osc/PLL details
tegra: Move ap20.h header into arch location
Add AES crypto library
i2c: Add TPS6586X driver
Add abs() macro to return absolute value
fdt: Add function to return next compatible subnode
fdt: Add function to locate an array in the device tree
i.MX28: Avoid redefining serial_put[cs]()
i.MX28: Check if WP detection is implemented at all
i.MX28: Add battery boot components to SPL
i.MX28: Reorder battery status functions in SPL
i.MX28: Add LRADC init to i.MX28 SPL
i.MX28: Add LRADC register definitions
i.MX28: Shut down the LCD controller before reset
i.MX28: Add LCDIF register definitions
i.MX28: Implement boot pads sampling and reporting
i.MX28: Improve passing of data from SPL to U-Boot
M28EVK: Add SD update command
M28EVK: Implement support for new board V2.0
FEC: Abstract out register setup
MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
i.MX28: Add delay after CPU bypass is cleared
spi: mxs: Allow other chip selects to work
spi: mxs: Introduce spi_cs_is_valid()
mx53loco: Remove unneeded gpio_set_value()
mx53loco: Add CONFIG_REVISION_TAG
mx53loco: Turn on VUSB regulator
mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
pmic: dialog: Avoid name conflicts
imx: Add u-boot.imx as target for ARM9 i.MX SOCs
i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
imx: usb: There is no such register
i.MX25: usb: Set PORTSCx register
imx: nand: Support flash based BBT
i.MX25: This architecture has a GPIO4 too
i.MX25: esdhc: Add mxc_get_clock infrastructure
i.MX6: mx6q_sabrelite: add SATA bindings
i.MX6: add enable_sata_clock()
i.MX6: Add ANATOP regulator init
mx28evk: add NAND support
USB: ehci-mx6: Fix broken IO access
M28: Scan only first 512 MB of DRAM to avoid memory wraparound
Revert "i.MX28: Enable additional DRAM address bits"
M28: Enable FDT support
mx53loco: Add support for 1GHz operation for DA9053-based boards
mx53loco: Allow to print CPU information at a later stage
mx5: Add clock config interface
imx-common: Factor out get_ahb_clk()
i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
mx31pdk: Allow booting a zImage kernel
mx6qarm2: Allow booting a zImage kernel
mx6qsabrelite: Allow booting a zImage kernel
mx28evk: Allow booting a zImage kernel
m28evk: Allow to booting a dt kernel
mx28evk: Allow to booting a dt kernel
mx6qsabrelite: No need to set the direction for GPIO3_23 again
pmic: Add support for the Dialog DA9053 PMIC
MX53: mx53loco: Add SATA support
MX53: Add support to ESG ima3 board
SATA: add driver for MX5 / MX6 SOCs
MX53: add function to set SATA clock to internal
SATA: check for return value from sata functions
MX5: Add definitions for SATA controller
NET: fec_mxc.c: Add a way to disable auto negotiation
Define UART4 and UART5 base addresses
EXYNOS: Change bits per pixel value proper for u-boot.
EXYNOS: support TRATS board display function
LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
EXYNOS: support EXYNOS MIPI DSI interface driver.
EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
LCD: add data structure for EXYNOS display driver
EXYNOS: add LCD and MIPI DSI clock interface.
EXYNOS: definitions of system resgister and power management registers.
SMDK5250: fix compiler warning
misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
misc:pmic:max8997 MAX8997 support for PMIC driver
TRATS: modify the trats's configuration
ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
cm-t35: add I2C multi-bus support
include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
omap3: Introduce weak misc_init_r
omap730p2: Remove empty misc_init_r
omap5912osk: Remove empty misc_init_r
omap4+: Remove CONFIG_ARCH_CPU_INIT
omap4: Remove CONFIG_SYS_MMC_SET_DEV
OMAP3: pandora: drop console kernel argument
OMAP3: pandora: revise GPIO configuration
...
GOT is now handled the way the main u-boot.lds does it. Without this,
the boot hangs when built with newer GCC (since 4.6). Older toolchains
hid the issue by converting -fpic to -fPIC.
Signed-off-by: Scott Wood <scottwood@freescale.com>
All arches init this the same way, so move the logic into the core
net code to avoid duplicating it everywhere else.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
In warm reset conditions on OMAP36xx/AM/DM37xx the rom code
incorrectly sets the DPLL4 clock input divider to /6.5 which
is an invalid value unless the input clock is 13MHz. When a JTAG
emulator is attached, a warm reset is necessary after the emulator
gains control of the process. This results in a loss of serial
output due to the invalid DPLL4 settings.
This patch fixes the issue by resetting the DPLL4 clock input
divider to /1 when the input clock is not 13MHz. AM/DM37x TRM
section 3.5.3.3.3.2.1 specifies that the /6.5 setting is only
used when the input clock is 13MHz.
Signed-off-by: Matt Porter <mporter@ti.com>
Booting up these cores (dsp / ivahd / cortex-m3) is bad without
firmware running on them, and they will hang preventing any kind
of sleep transitions later on with the kernel.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: R Sricharan <r.sricharan@ti.com>
If this is done in the bootloader, the FS-USB will later be stuck into
intransition state, which will prevent the device from entering idle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is needed for upcoming Toradex Colibri T20 upstream support.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra keyboard controller provides a simple interface to a matrix
keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add tegra_i2c_get_dvc_bus_num() to obtain the I2C bus number of DVC bus.
This allows us to talk to the PMU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a definition of the memory controller node according to the bindings
here:
http://patchwork.ozlabs.org/patch/132928/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Save SDRAM parameters into the warmboot scratch registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to set up the warm boot area in the Tegra CPU ready for a
resume after suspend.
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Power supplies must be adjusted in line with clock frequency. This code
provides a simple routine to set the voltage to allow operation at maximum
frequency.
- Split PMU code into separate TPS6586X driver
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for setting up the memory controller parameters. Boards
can set up an appropriate table in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a basic header file for this register, to be filled in as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to know which type of chip we are running on - the Tegra
family has several SKUs. This can be determined by reading a
fuse register, so add this function to ap20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These headers provide access to additional Tegra features.
flow - start/stop CPUs
sdram - parameters for SDRAM
fuse - access to on-chip fuses / security settings
gp_padctl - pad control and general purpose registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Provides an interface to aes.c for the warmboot code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add clock_ll_read_pll() to read PLL parameters and clock_get_osc_bypass()
to find out if the Oscillator is bypassed. These are needed by warmboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to include this from board code, so move the header into
an easily-accessible location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This macro is generally useful to make it available in common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Do not define serial_putc() and serial_puts() calls if
CONFIG_SPL_SERIAL_SUPPORT is set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This code is part of battery boot support for i.MX28.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
If the LCD controller is on before the CPU goes into reset, the traffic on LCDIF
data pins interferes with the BootROM's boot mode sampling. So shut the
controller down.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Pass memory size from SPL via structure located in SRAM instead of SCRATCH
registers. This allows passing more data about boot from SPL to U-Boot, like the
boot mode pads configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
After an update to the MX51 reference manual (Rev. 5), the
values of the PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH
are now clearly wrong:
"Bit 13:
High / Low Output Voltage Range. This bit selects the output voltage mode for
SD2_CMD. 0 High output voltage mode
1 Low output voltage mode"
The values are currently negated in code - fixed.
Reported-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: David Jander <david.jander@protonic.nl>
Acked-by: David Jander <david.jander@protonic.nl>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This solves issues when larger amount of DRAM is used, like 256MB.
Behave the same in case of CPU bypass as we do in case of EMI
bypass, but wait 15 ms. We need to wait until the clock domain
stabilizes.
This issue seemed to have been caused by not waiting after frobbing
with the CPU bypass, it was unrelated to memory, but had a direct
impact, causing trouble. This was yet another X-File of the
imx-bootlets, sigh. The conclusion is, trying a semi-random delay
(there is delay after the EMI bypass change), the issue is fixed.
Another possible explanation is that we do not do the "simple memory
test" FSL does in their imx-bootlets (1000 R/W cycles to/from piece of
the memory, while also outputing something on the serial port). This
might have caused the similar delay in the imx-bootlets and therefore
they didn't need to add this explicitly.
For now, this seems good fix enough, but to me, whole that memory
init code in imx-bootlets is completely flunked and it'd need deeper
investigation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.
The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.
Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
types.h must be included in imx-regs.h if one wants to include
imx-regs.h in a board configuration file. That for one's part is
necessary, if one wants to use addresses defined in imx-regs.h.
For example, fsl_esdhc.c needs CONFIG_SYS_FSL_ESDHC_ADDR defined and
a proper thing is to define it with IMX_MMC_SDHCx_BASE in board
configuration file. This patch fixes the build in that case.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Defining CONFIG_FSL_ESDHC brings in a call to get_clocks, so let's
implement get_clocks function. This is how it seems to be implemented
elsewhere.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Init the core regulator voltage to 1.2V. This is required for the correct
functioning of the GPU and when the ARM LDO is set to 1.225V. This is a
workaround to fix some memory clock jitter.
Note: This should be but can't be done in the DCD. The bootloader
prevents access to the ANATOP registers.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
This reverts commit 69d26d09de.
Apparently, this commit got mainline only because of out-of-tree
port and causes breakage on board that is mainline. Revert.
Reason:
* The OOT board has 512MB of DRAM, enabling this additional address
line enabled it to work fine with 512MB of RAM.
* Every mainline port has max. 256MB of DRAM, therefore this revert
has no impact on any mainline port
* Though this caused a problem with new M28 board with 256MB of DRAM
where the chips are wired differently. The patch-to-be-reverted
caused the DRAM to behave like this:
[128MB chunk #1][128MB chunk #1 again][128MB chunk #2][128MB chunk #2 again]
Therefore to retain the current one-memory-init-rules-them-all situation,
revert this patch until another board emerges and will actually be pushed
mainline that needs different setup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Print CPU information within board_late_init().
This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx5: Add clock config interface
Add clock config interface support, so that we
can configure CPU or DDR clock in the later init
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
get_ahb_clk() is a common function between mx5 and mx6.
Place it into imx-common directory.
Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The MX53 SATA interface can use an internal clock (USB PHY1)
instead of an external clock. This is an undocumented feature, but used
on most Freescale's evaluation boards, such as MX53-loco.
As stated by Freescale's support:
Fuses (but not pins) may be used to configure SATA clocks.
Particularly the i.MX53 Fuse_Map contains the next information
about configuring SATA clocks :
SATA_ALT_REF_CLK[1:0] (offset 0x180C)
'00' - 100MHz (External)
'01' - 50MHz (External)
'10' - 120MHz, internal (USB PHY)
'11' - Reserved
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Add base address and MXC_SATA_CLK to return
the clock used for the SATA controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI
based LCD Panel could be used with it. This patch supports MIPI-DSI driver
based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
board file and LCD panel driver specific function registered to mipi_dsim_ddi
structure at lcd panel init function called system init.
In the MIPI-DSI driver, find lcd panel driver by using registered
lcd panel name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch support EXYNOS FB and FIMD display drivers.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is definitions of system registers and power mananagement registers for EXYNOS SoC.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc
in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic
usase of tzpc.
Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This rule confirms that if we're on ARM and we have enabled THUMB builds
that we have a new enough toolchain to produce a working binary.
Changes in v2:
- Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F)
- Simplfy checkthumb test after doing the above
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.
Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: Aneesh V <aneesh@ti.com>
Enable -march=armv7-a for armv7 platforms if the tool-chain
supports it. This in turn results in Thumb-2 code generated
for these platforms if CONFIG_SYS_THUMB_BUILD is enabled.
Signed-off-by: Aneesh V <aneesh@ti.com>
Enable Thumb build and ARM-Thumb interworking based on the new
config flag CONFIG_SYS_THUMB_BUILD
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
Warm reset is not functional in case of omap5430ES1.0.
So override the weak reset_cpu function to use
cold reset instead.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The break statement is missing in init_omap_revision function, resulting
in a wrong revision identification. So fixing this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.
Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
http://lists.denx.de/pipermail/u-boot/2012-March/119151.html
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.
As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This change adds initial support for NXP LPC32x0 SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: bfin_sdh: drop dos part hardcode
Blackfin: move gd/bd to bss by default
Blackfin: gd_t: relocate volatile markings
* 'master' of git://git.denx.de/u-boot-nds32:
board/adp-ag102: add configuration of adp-ag102
board/adp-ag102: add board specific files
nds32/ag102: add ag102 soc support
nds32/ag102: add header support of ag102 soc
* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
CMD: Remove CMD_LOG, it's unused
CMD: Fix typo KGBD -> KGDB on debris board
CMD: Drop CONFIG_CMD_EMMC, it's not used
CMD: Drop CONFIG_CMD_DFL, it's not used
CMD: Drop CMD_DCR, it's not used
CMD: Drop CMD_CAN, it's not used
CMD: Remove CMD_AUTOSCRIPT, it's not used
AT91: Drop AT91_SPIMUX command from cmd_all
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.
Signed-off-by: Timur Tabi <timur@freescale.com>
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.
Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Currently "u-boot", the elf file generated via u-boot-nand.lds does not
contain required debug information i.e. .debug_{line, info, abbrev, aranges,
ranges} into their respective _global_ sections.
The original ld script line arch/powerpc/cpu/mpc85xx/start.o
KEEP(*(.bootpg)) is not entirely correct because the start.o file is already
processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will
not process start.o again for bootpg.
So Fix u-boot-nand.lds to generate these debug information.
Signed-off-by: Anmol Paralkar <b07584@freescale.com>
Signed-off-by: John Russo <John.Russo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
NAND SPL code never compile the vector table.
So no need to setup interrupt vector table for NAND SPL.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After relocation of vector table in SDRAM's lower address, IVORs value should
be updated with new handler addresses.
As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs
are updated with 0x100, 0x200,....f00 hard-coded values.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.
in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Vipin KUMAR
Amit Virdi
Tetsuyuki Kobayashi
SRICHARAN R
Sebastien Jan
Steve Sakoman
Lokesh Vutla
Valentin Longchamp
Bo Shen
Michael Langer
Marek Vasut
Otavio Salvador
Fabio Estevam
Jason Liu
Rajeshwari Shinde
Minkyu Kang
Tom Rini
Troy Kisky
Tom Warren
Tom Warren
amartin@nvidia.com
Simon Glass
Stephen Warren
Lucas Stach
York Sun
Timur Tabi
Prabhakar Kushwaha
Wolfgang Denk
Andreas Bießmann
Daniel Schwierzeck
Phil Edworthy
Nobuhiro Iwamatsu
Jeroen Hofstee
Donghwa Lee
Joe Hershberger
Anatolij Gustschin
Scott Wood
Mike Frysinger
Matt Porter
Tero Kristo
Anton Staff
Yen Lin
Jimmy Zhang
Marek Vasut
Stefano Babic
Timo Ketola
Eric Nelson
Dirk Behme
Fabio Estevam
Chander Kashyap
Grazvydas Ignotas
Aneesh V
Balaji T K
Nishanth Menon
Jonathan Solnit
Vladimir Zapolskiy
Jaehoon Chung
Liu Gang