DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Freescale's SEC block has built-in Data Encryption
Key(DEK) Blob Protocol which provides a method for
protecting a DEK for non-secure memory storage.
SEC block protects data in a data structure called
a Secret Key Blob, which provides both confidentiality
and integrity protection.
Every time the blob encapsulation is executed,
a AES-256 key is randomly generated to encrypt the DEK.
This key is encrypted with the OTP Secret key
from SoC. The resulting blob consists of the encrypted
AES-256 key, the encrypted DEK, and a 16-bit MAC.
During decapsulation, the reverse process is performed
to get back the original DEK. A caveat to the blob
decapsulation process, is that the DEK is decrypted
in secure-memory and can only be read by FSL SEC HW.
The DEK is used to decrypt data during encrypted boot.
Commands added
--------------
dek_blob - encapsulating DEK as a cryptgraphic blob
Commands Syntax
---------------
dek_blob src dst len
Encapsulate and create blob of a len-bits DEK at
address src and store the result at address dst.
Signed-off-by: Raul Cardenas <Ulises.Cardenas@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ulises Cardenas <ulises.cardenas@freescale.com>
Signed-off-by: Ulises Cardenas-B45798 <Ulises.Cardenas@freescale.com>
The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs.
Add a new function mx6sx_dram_iocfg to configure dram io.
Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1
to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1
effects as "mmdc1->entry=value".
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Add api to check and enable pll3 as required
for thermal sensor driver.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Move MX5 specific set_chipselect_size function into generic i.MX part,
such that MX6 based boards are able to use this function as well.
While doing this the iomuxc gpr member needed to be consolidated between
MX5 and MX6.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
i.MX6SX ROM implements unified table sections.
The HAB function table is at offset 0x100. Update
the HAB function pointers accordingly.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The mx6sl/mx6sx has 2 OTG and 1 host. So they have name
"USBO2H_USB_BASE_ADDR" in imx-regs.h. The driver hard codes
the USB base address name to "USBOH3", which causes the driver
failed to build for mx6sl/mx6sx.
This patch uniform the address name to "USB_BASE_ADDR" for all
mx6 series.
Signed-off-by: Ye.Li <B37916@freescale.com>
When CONFIG_SECURE_BOOT is enabled, the signed images
like kernel and dtb can be authenticated using iMX6 CAAM.
The added command hab_auth_img can be used for HAB
authentication of images. The command takes the image
DDR location, IVT (Image Vector Table) offset inside
image as parameters. Detailed info about signing images
can be found in Freescale AppNote AN4581.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
mx6sxsabresd board has 2 FEC ports, each one connected to a AR8031.
Add support for one FEC port initially.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This allows u-boot to load different OS or Bare Metal application on
different cores of the i.MX6 SoC.
For example: running Android on cpu0 and a RT OS like QNX/FreeRTOS on cpu1.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Stefano Babic <sbabic@denx.de>
According to the Reference Manual the 'mask_periph2_clk_sel_loaded' field of
register CCM_CIMR corresponds to bit 19 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'wb_per_at_lpm' field of register
CCM_CLPCR corresponds to bit 16 so fix its definition accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
According to the Reference Manual the 'spdif0_clk_podf' field of register
CCM_CDCDR corresponds to bits 22, 23 and 24, so fix the mask and offset
definitions accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
'omux' field is not used anywhere and such layout is not valid for mx6solox.
Instead of adding more ifdef's into the structure, let's simply remove this
unused 'omux' field.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
On mx6solox there is an additional 0x4000 offset for the GPR registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no need to keep iomuxc_base_regs structure as it serves the exact same
purpose of the iomuxc structure, which is to provide access to the GPR
registers.
The additional fields of iomuxc_base_regs are not used. Other advantage of
'iomuxc' is that it has a shorter name and the variable declarations can fit
into a single line.
So remove iomuxc_base_regs structure and use iomuxc instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx6solox is the newest member of the mx6 family.
Some of the new features on this variants are:
- Cortex M4 microcontroller (besides the CortexA9)
- Dual Gigabit Ethernet
Add the initial support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not
set in the same way as DISP0_DAT00-23, causing much flicker
in parallel RGB displays on Dual-Lite and Solo processors.
These settings now match the i.MX6 Dual and Quad core versions.
Note that this fixes a regression in commit b47abc3 and that
this is the second time we've had a regression on these two
pads (See commit e654ddf).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
According to:
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/log/?h=imx_v2009.08_3.0.35_4.1.0
ENGR00287268 mx6: fix the secure boot issue on the new tapout chip
commit 424cb1a79e9f5ae4ede9350dfb5e10dc9680e90b
newer i.MX6 silicon revisions have an updated ROM and HAB API table.
Please see also:
i.MX Applications Processors Documentation
Engineering Bulletins
EB803, i.MX 6Dual/6Quad Applications Processor Silicon Revsion 1.2 to 1.3 Comparison
With this change the secure boot status is correctly displayed
Signed-off-by: Stefano Babic <sbabic@denx.de>
mx6 reference manual incorrectly states that the DEVICE_TYPE field of
IOMUXC_GPR12 register should be configured as '0010' for setting the PCI
controller in RC mode. The correct value should be '0100' instead.
This also aligns with the same value used in the mx6 pci kernel driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
- add function for configuring iomux based on board-specific regs
- add function for configuring mmdc based on board-specific and
chip-specific data
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add memory-mapped structures for MMDC iomux and configuration. Note that whi
the MMDC configuration registers are common between the IMX6DQ
(IMX6DUAL/IMX6QUAD) and IMX6SDL (IMX6SOLO/IMX6DUALLITE) types the iomux
registers differ. This requires two sets of structures.
Add structures to describe DDR3 device information, system information
(memory layout, etc), and MMDC calibration registers that can be used to
configure the MMDC dynamically.
We define these structures for SPL builds instead of including mx6q-ddr.h an
mx6dl-ddr.h which use the same namespace and are only useful for imximage cf
files.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The dual lite and solo variant have only 4 SPI controller.
respect this in the MXC_SPI_BASE_ADRESSES macro
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tim Harvey
Raul Cardenas
Otavio Salvador
Peng Fan
Ye.Li
Tom Rini
Stefan Roese
Nikita Kiryanov
Nitin Garg
Fabio Estevam
Soeren Moch
Anatolij Gustschin
Gabriel Huau
Heiko Schocher
Eric Nelson
Stefano Babic
Andy Ng
Markus Niebel
Markus Niebel