Commit graph

94 commits

Author SHA1 Message Date
Thomas Chou
de99a17c9a net: zap altera_tse_initialize prototypes
Zap the altera_tse_initialize() prototypes, since it is converted
to driver model.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-11-12 08:26:59 +08:00
Bin Meng
ca19a79342 net: pch_gbe: Convert to driver model
This commit converts pch_gbe ethernet driver to driver model.

Since this driver is only used by Intel Crown Bay board, the
conversion does not keep the non-dm version.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-09-09 07:48:03 -06:00
Hans de Goede
d17e1577a2 sunxi: emac: Remove non driver-model code
All sunxi boards now use the driver-model, so remove the non driver-model
code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
aab096401c sunxi: gmac: Move sunxi_gmac_initialize proto out of netdev.h
netdev.h should not be included in driver-model enabled builds (doing so
causes compiler warnings about struct eth_driver not being declared), but
we do use sunxi_gmac_initialize in the driver-model case, so move it out of
netdev.h .

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Albert ARIBAUD \(3ADEV\)
ac2916a224 lpc32xx: add Ethernet support
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10 14:22:48 +02:00
Bin Meng
8ee443b8eb net: Add Intel Topcliff GMAC driver
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff
Platform Controller Hub. Tested under 10/100 half/full duplex and 1000
full duplex modes using ping and tftpboot commands.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-03-24 21:22:37 -06:00
Masahiro Yamada
a2f39e830e ARM: remove cm4008 and cm41xx board support
These are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
2015-02-24 17:07:11 -05:00
Michal Simek
5840537879 net: gem: Use phys_addr_t instead of int for addresses
Use phys_addr_t for physical address declaration.
It is also unsigned type instead of sign.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-01-21 10:30:21 +01:00
Stefan Roese
19fc2eae6d net: mvneta.c: Add support for the ethernet controller of the Marvell Armada XP SoC
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.

Tested on the Marvell MV78460 eval board db-78460-bp.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
2014-10-23 09:59:21 -04:00
Jiandong Zheng
799e125cca arm: bcm281xx: net: Add Ethernet Driver
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.

Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
2014-08-30 07:46:39 -04:00
Masahiro Yamada
368b4d2b49 drivers: net: remove dead drivers
The following configs are not defined at all:

 - CONFIG_INCA_IP_SWITCH
 - CONFIG_PBL2800_ETHER
 - CONFIG_PHY_ICPLUS

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-21 12:01:11 -04:00
Stefan Roese
b70ed300b0 net: Rename and cleanup sunxi (Allwinner) emac driver
There have been 3 versions of the sunxi_emac support patch during its
development. Somehow version 2 ended up in upstream u-boot where as
the u-boot-sunxi git repo got version 3.

This bumps the version in upstream u-boot to version 3 of the patch:
- Initialize MII clock earlier so mii access to allow independent use
- Name change from WEMAC to EMAC to match mainline kernel & chip manual
- Cosmetic code cleanup

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-07-06 20:12:44 +01:00
Ian Campbell
5835823da3 sunxi: add gmac Ethernet support
Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i)
processors. Enable for the Cubietruck.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
2014-05-25 16:25:12 +02:00
Daniel Schwierzeck
538cf92c8c MIPS: drop incaip board
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
2014-04-20 13:16:43 +02:00
Michal Simek
f88a6869a1 net: gem: Add OF initialization support
Gem can be directly initialized from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:35 -05:00
Michal Simek
0c9c99a20b net: emaclite: Fix OF initialization
- Add xilinx_emaclite_of_init to netdev.h
- Remove global data pointer from the driver
- Add better handling for error state.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:32 -05:00
Alexey Brodkin
92a190aaab net/designware - switch driver to phylib usage
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
 * Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
 * Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
 * Support of custom phy initialization is now done with existing
"board_phy_config".

Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.

For example:
 * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
 * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used

I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07 09:16:46 -05:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Kuo-Jung Su
c4775476d2 net: add Faraday FTMAC110 10/100Mbps ethernet support
Faraday FTMAC110 10/100Mbps supports half-word data transfer for Linux.
However it has a weird DMA alignment issue:

(1) Tx DMA Buffer Address:
    1 bytes aligned: Invalid
    2 bytes aligned: O.K
    4 bytes aligned: O.K

(2) Rx DMA Buffer Address:
    1 bytes aligned: Invalid
    2 bytes aligned: O.K
    4 bytes aligned: Invalid!!!

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Tom Rini <trini@ti.com>
2013-06-24 19:11:16 -05:00
Roberto Cerati
45a1693a31 net: ks8851_mll: add ethernet support
The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.

Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
2013-06-24 19:11:14 -05:00
Henrik Nordström
518ce472f7 net: Add sunxi (Allwinner) wemac driver
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.

From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
2013-06-24 19:07:31 -05:00
Albert ARIBAUD
a19b0dd62d Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	common/cmd_fpga.c
	drivers/usb/host/ohci-at91.c
2013-05-30 14:45:06 +02:00
Wolfgang Denk
d6ed322222 Power: remove support for Freescale MPC8220
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.

Remove the code to avoid wasting maitaining efforts on dead stuff.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
2013-05-15 08:41:03 -04:00
David Andrey
01fbf31042 net: gem: Preserve clk on emio interface
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO

Do not enable emio for this standard board configuration for now.

Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:24 +02:00
David Andrey
117cd4cc10 net: gem: Pass phy address to init
Pass the PHY address to the driver init to
allow parallel use of both interfaces

Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:23 +02:00
Troy Kisky
fe428b909b net: fec_mxc: get phydev before fec_probe
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:51 +01:00
Albert ARIBAUD
0a16ea5933 mv88e61xx: refactor PHY and SWITCH level-code
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-01-09 04:12:10 +05:30
Michal Simek
185f7d9afc net: Add driver for Zynq Gem IP
Device driver for Zynq Gem IP.

Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2012-09-26 12:36:32 -05:00
Vipin Kumar
9afc1af01f SPEAr: Add interface information in initialization
Few Designware peripheral registers need to be modified based on the
ethernet interface selected by the board. This patch supports interface
information in ethernet driver

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-07-07 14:07:40 +02:00
Stephan Linz
df48265036 net: ll_temac: Add LL TEMAC driver to u-boot
Xilinx LocalLink Tri-Mode Ether MAC driver can be
used by Xilinx Microblaze or Xilinx ppc405/440 in
SDMA and FIFO mode. DCR or XPS bus can be used.

The driver uses and requires MII and PHYLIB.

CP: 4 warnings: 'Use of volatile is usually wrong'
I won't fix this, because it depends on the network
driver subsystem.

Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04 09:36:19 -05:00
Rob Herring
efdd731957 net: add Calxeda xgmac driver
This adds ethernet driver for Calxeda xgmac found on Highbank SOC.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>

Fix: WARNING: __aligned(size) is preferred over
__attribute__((aligned(size)))
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-01-05 20:10:38 +01:00
Bernhard Kaindl
d020169298 ne2000: Convert to new net-multi model, fixes build of three boards
This fixes the build of the two sh boards shmin and r7780mp and qemu-mips
which currently fail to build due to dropped pre-CONFIG_NET_MULTI code.

This v2 patch minimizes the number of lines in the diff for easy review
and to eliminate any possible accidential changes resulting from moving
lines of code in the file. This also makes the register function very easy.

Any cleanups and improvements are intentionally deferred to follow-up patches
to keep this patch as simple and as easy to review as possible.

A new driver register function, ne2k_register() calls the existing
one-time setup part of the old init function and calls eth_register().

Changes to shmin, r7780mp and qemu-mips:
- Call the new ne2k_register() from board_eth_init() of the boards.

- Tested using qemu-mips board,
- Tested the two renesas / sh boards r7780mp and shmin to compile again,
  and should work.

checkpatch-clean when "--ignore VOLATILE" is added to .checkpatch.conf,
and no warnings introduced in none of the three boards using this driver.

Signed-off-by: Bernhard Kaindl <bernhard.kaindl@gmx.net>
2011-12-08 22:22:03 +01:00
Joachim Foerster
b962ac794a altera_tse: Add support for dedicated descriptor memory
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
2011-10-26 21:27:37 +02:00
Michal Simek
c1044a1ec1 net: emaclite: Move RX/TX ping pong initialization to
Init RX/TX ping pong directly from board not in the driver.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-23 23:32:44 +02:00
Michal Simek
9b94755af9 net: emaclite: Use unsigned long for baseaddr
Baseaddr should be unsigned long.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-23 23:32:44 +02:00
Michal Simek
4f1ec4c176 net: axi_ethernet: Add driver to u-boot
Add axi_ethernet driver for little-endian Microblaze.

RX/TX BDs and rxframe buffer are shared among all axi_ethernet MACs.
Only one MAC can work in one time.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-15 22:12:05 +02:00
Marek Vasut
2e5f44213f FEC: Allow registering MII postconfiguration callback
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:02 +02:00
Marek Vasut
9e27e9dca1 FEC: Allow multiple FECes
This patch allows user to register multiple FEC controllers. To preserve
compatibility with older boards, the mxcfec_register() call is still in place.
To use multiple controllers, new macro is in place, the mxcfec_register_multi(),
which takes more arguments. The syntax is:

mxcfec_register_multi(bd, FEC ID, FEC PHY ID on the MII bus, base address);

To disable the fecmxc_register() compatibility stuff, define the macro
CONFIG_FEC_MXC_MULTI. This will remove the requirement for defining IMX_FEC_BASE
and CONFIG_FEC_MXC_PHYADDR.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Ajay Bhargav
79788bb19a net: Adds Fast Ethernet Controller driver for Armada100
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
2011-09-30 22:00:53 +02:00
Wolfgang Denk
bd6ce9d171 cm4008, cm41xx: fix build warnings
Fix these:
cm4008.c: In function 'board_eth_init':
cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'

cm41xx.c: In function 'board_eth_init':
cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'

While we are at it, sort include list in netdev.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
2011-09-10 17:00:51 +02:00
Greg Ungerer
1e8ff7145c KS8695: convert KS8695 eth driver to CONFIG_MULTI_ETH
Trivial conversion of the ks8695eth driver to a CONFIG_MULTI_ETH type
driver.

Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
2011-09-10 16:10:34 +02:00
Stefano Babic
b9bb053159 Add support for MX35 processor
The patch adds basic support for the Freescale's i.MX35
(arm1136 based) processor.

The patch adds also a prototype for the initialization
of the FEC(ethernet controller) to netdev.h to avoid
warnings.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2011-02-02 00:54:42 +01:00
Macpaul Lin
b3dbf4a51f ftgmac100: support of gigabit eth ftgmac100
Add Faraday's ftgmac100 (gigabit ethernet)
MAC controller's driver.

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-01-09 22:16:51 +01:00
Michal Simek
042272a6f2 net: Move Emaclite to NET_MULTI
Emaclite was using old net api that's why
this patch move emaclite to NET_MULTI api.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11 23:07:04 -07:00
Reinhard Meyer
a61a81967f NET: add ENC28J60 driver using SPI framework
V3: further refinements:
- use priv member instead of container method
- allow setting of MAC address by write_hwaddr method
- avoid shutting down link between commands

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11 22:47:48 -07:00
Joakim Tjernlund
91955834f5 net: Fix faulty definition of uec_initialize()
The correct definition is in drivers/qe/uec.h so just
remove this one.

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11 22:47:47 -07:00
Albert Aribaud
d44265ad78 mvgbe: support SoCs other than kirkwood
Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 23:40:31 -07:00
Mike Frysinger
36de211060 AX88180: add missing init prototype
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 00:14:28 -07:00
Vipin KUMAR
5b1b1883ff SPEAr : Network driver support added
Designware network driver support added.
This is a Synopsys ethernet controller

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 00:08:05 -07:00
Thomas Chou
c960b13ed2 net: add altera triple speeds ethernet mac driver
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00