Some boards use device tree for almost all board-specific configuration.
They therefore do not need their own separate board code, but can all use
the same version. Add a common version of the board code. It uses the
PMIC, regulator and video bridge uclasses. This will support smdk5250,
smdk5420, snow, spring, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.
In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Disable a few things which interfere with the EFI init. This allows QEMU to
to boot into EFI, load a U-Boot payload then boot to the U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Disable a few things which interfere with the EFI init. This allows the
Minnowboard MAX to boot into EFI, load a U-Boot payload then boot to the
U-Boot prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for the efi-x86 board, which supports running U-Boot as an
EFI 32-bit application.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On Intel BayTrail SoC, there is a legacy UART (I/O 0x3f8) integrated
into the SoC which is enabled by the FSP. Remove the smsc47x superio
initialization codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On LS1021A Rev2.0, OCRAM's security level needs to be changed to
non-secure access for SD boot. This patch will allow OCRAM
access permission as R/W in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Program the external regulator to switch off voltage in deep sleep.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Refactor display code to only setup hdmi if do_enable_hdmi() is invoked.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for selecting display preset using the environment variable
"displaytype". This is a preparation for future merging of compulab
omap3_display.c display selection code with the cm-fx6 display selection code.
The "panel" environment variable is retained for backwards compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Implement a cm-fx6 specific board_video_skip() to provide the option to not
initialize the display.
The new function does not init display if the environment variable "panel" is
not defined, or if it is set to an unsupported value.
Collateral changes:
- Don't use the global displays array (it's CONFIG_IMX_VIDEO_SKIP specific).
- Don't use detect_hdmi(), since env controlled init makes it unnecessary.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
U-Boot does not explicitly assign the display to an IPU interface. Instead, it
relies on the power-on default of DI0.
Since the kernel reassigns HDMI display to DI1, after a warm reset the HDMI
display no longer works in U-Boot.
Fix this by explicitly assigning HDMI to IPU1 DI0 in U-Boot.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
Build target: mx6qpsabreauto_config
Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
PMIC: PFUZE100 ID=0x10
Flash: 32 MiB
NAND: 0 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Detect the SOC and board variant at runtime and change the dtb name,
but not hardcoding the fdt_file env variable.
Take the following patch as a reference.
Íd58699b157df75f1aa0b363ea9c21add21a0c
"mx6cuboxi: Load the correct 'fdtfile' variable"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
sw variable in checkboard function is storing vbank value
which can only take 3-bit value.
So check of sw value for if greater than 7 is redundant.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
eMMC has no CD and WP pins, it needs to add board-specific
board_mmc_getcd() and board_mmc_getwp() in SPL to support
eMMC boot without external SD card inserted.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for NOR flash and GPIO/I2C switch control on RevC.
- NOR support
- bank0/bank4 switch
- SD/eMMC switch
- board version
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P5020 and P5040.
The Secure boot target has already been added for P3041 by
enabling CONFIG_SYS_RAMBOOT and configuring CPC as SRAM.
The targets for P5020 and P5040 are added in the same manner.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update PBI command in pbi_cfg files to keep register bit
to default reset value while configuring CPC
as SRAM
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
cpld reset altbank should always reset to bank4 no matter what
current bank is.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Because the function ft_board_setup() delete the USB2 device node, it
leads to can't find the device node and hung up.
In fact only P1020RDB needs to delete the USB2 node, this patch fixes
this issue.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
defconfig files are added and SFP version for these platforms
is updated.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
T1040D4RDB is re-designed T1040RDB board with following changes :
- Support of DDR4 memory
- Support of 0x66 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
- Support of QE-TDM
Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
- Support of DDR4 memory
- Support for 0x86 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
- Support of DIU
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.
With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the zynqmp Kconfig from board to arch
as there may be different boards under same
architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable the I2C3 pins so that the TPM can be used.
Note: There is an DP change also, caused by running board-to-uboot.py
script in the latest tegra-pinmux-script tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_LINUX_BOOT_PARAM_ADDR is not a valid configuration option. Do
just like what the rest of the world does.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.
By the way, there are exceptions for the statement above; host
programs. In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not. So, some
files still include <linux/config.h> to work around build errors
on host tools.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Fix up a few typos in documentation.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Simon Glass
Tom Rini
Hans de Goede
Paul Kocialkowski
Ben Stoltz
Bin Meng
Alison Wang
chenhui zhao
Tang Yuantian
Peng Fan
Nikita Kiryanov
Priyanka Jain
Shengzhou Liu
Aneesh Bansal
Shaohui Xie
Ying Zhang
gaurav rana
Tom Warren
Michal Simek
Siva Durga Prasad Paladugu
Nishanth Menon
Antonio Borneo
Masahiro Yamada
Otavio Salvador