The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.
The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.
The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.
Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
To add the DesignWare watchdog driver support. It required
information such as register base address and clock info from
configuration header file within include/configs folder.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
In current gpio_set_value() implementation, it always sets the gpio control bit
no matter the value argument is 0 or 1. Thus the GPIOs never set to low.
This patch fixes this bug.
The address bus is used as a mask on read/write operations, so that independent
software drivers can set their GPIO bits without affecting any other pins in a
single write operation. Thus we don't need a read-modify-write to update the
register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Almost all of ci_udc.c uses variable name "ep" for a struct usb_ep and
"ci_ep" for a struct ci_ep. This is nice and consistent, and helps people
know what type a variable is without searching for the declaration.
handle_ep_complete() doesn't do this, so fix it to be consistent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A UDC's alloc_request method should zero out the newly allocated request.
Ensure the Atmel driver does so. This issue was found by code inspection,
following the investigation of an intermittent issue with ci_udc, which
was tracked down to failing to zero out allocated requests following some
of my changes. All other UDC drivers already zero out requests in one
way or another.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct ci_req is a purely software structure, and needs no specific
memory alignment. Hence, allocate it with calloc() rather than
memalign(). The use of memalign() was left-over from when struct ci_req
was going to hold the aligned bounce buffer, but this is now dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There's no need to store an array of QTD pointers in the controller.
Since the calculation is so simple, just have ci_get_qtd() perform it
at run-time, rather than pre-calculating everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2 QTDs are allocated for each EP. The current allocation scheme aligns
the first QTD in each pair, but simply adds the struct size to calculate
the second QTD's address. This will result in a non-cache-aligned
addresss IF the system's ARCH_DMA_MINALIGN is not 32 bytes (i.e. the
size of struct ept_queue_item).
Similarly, the original ilist_ent_sz calculation aligned the value to
ARCH_DMA_MINALIGN but didn't take the USB HW's 32-byte alignment
requirement into account. This doesn't cause a practical issue unless
ARCH_DMA_MINALIGN < 32 (which I suspect is quite unlikely), but we may
as well fix the code to be explicit, so it's obviously completely
correct.
The new value of ILIST_ENT_SZ takes all alignment requirements into
account, so we can simplify ci_{flush,invalidate}_qtd() by simply using
that macro rather than calling roundup().
Similarly, the calculation of controller.items[i] can be simplified,
since each QTD is evenly spaced at its individual alignment requirement,
rather than each pair being aligned, and entries within the pair being
spaced apart only by structure size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This will allow functions other than ci_udc_probe() to make use of the
constants in a future change.
This in turn requires converting the const int variables to #defines,
since the initialization of one global const int can't depend on the
value of another const int; the compiler thinks it's non-constant if
that dependency exists.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix ci_ep_submit_next_request()'s ZLP transmission code to explicitly
call ci_get_qtd() to find the address of the other QTD to use. This
will allow us to correctly align each QTD individually in the future,
which may involve leaving a gap between the QTDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_udc_probe() initializes a pair of QHs and QTDs for each EP. After
each pair has been initialized, the pair is cache-flushed. The
conversion from QH/QTD index [0..2*NUM_END_POINTS) to EP index
[0..NUM_ENDPOINTS] is incorrect; it simply subtracts 1 (which yields
the QH/QTD index of the first entry in the pair) rather than dividing
by two (which scales the range). Fix this.
On my system, this avoids cache debug prints due to requests to flush
unaligned ranges. This is caused because the flush calls happen before
the items[] array entries are initialized for all but EP0.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add LAN9500A product ID (0x9e00) in order to support LAN9500A based dongles.
Tested on cm_t335.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
cb_getvar tries to prevent overflowing the response buffer
by using strncat. But strncat takes the number of data bytes
copied as a limit not the total buffer length so it can still
overflow. Pass the correct value instead.
cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
cc: Rob Herring <robh@kernel.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Because of the brackets the & and && is evaluated before
the comparison. This is likely not the intention. Change
it to test the first and second condition to both be true.
cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
since ALLOC_CACHE_ALIGN_BUFFER defines a pointer and not a
buffer, the memset with sizeof(rqt) likely does something else
then intended. Since there is a memcpy directly after it with
the full size, drop the memset completely.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Since the struct fsg_common is calloced, reset it completely
with zero's when reused. While at it, make checkpatch happy.
cc: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Initialization of r8a66597 info structure is not enough.
Because initilization was used size of pointer.
This fixes that use size of r8a6659 info structure.
Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
This driver is processed as two USB hub despite one.
The number of root hub is defined in R8A66597_MAX_ROOT_HUB.
This fixes that register is accessed by using the definition
of R8A66597_MAX_ROOT_HUB.
Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
For plain array const can be either before or after
the type definition. Adding both is simply redundand.
Remove the later one.
cc: marex@denx.de
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
ci_udc.c's usb_gadget_unregister_driver() doesn't call driver->unbind()
unlike other USB gadget drivers. Fix it to do this.
Without this, when ether.c's CDC Ethernet device is torn down,
eth_unbind() is never called, so dev->gadget is never set to NULL.
For some reason, usb_eth_halt() is called both at the end of the first
use of the Ethernet device, and prior to any subsequent use. Since
dev->gadget is never cleared, all calls to usb_eth_halt() attempt to
stop, disconnect, and clean up the device, resulting in double cleanup,
which hangs U-Boot on my Tegra device at least.
ci_udc allocates its own singleton EP0 request object, and cleans it up
during usb_gadget_unregister_driver(). This appears necessary when using
the USB gadget framework in U-Boot, since that does not allocate/free
the EP0 request. However, the CDC Ethernet driver *does* allocate and
free its own EP0 requests. Consequently, we must protect
ci_ep_free_request() against double-freeing the request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Since p->bus is unsigned checking for negative values
is optimized away. Since bus is already used as an argument
use tmp. While at it, don't declare variables in the middle
of a function.
cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SPI recieve and transfer code in exynos_spi driver has a logical bug.
We read data in a variable which can hold an integer. Then we assign
this integer 32 bit value to another variable which has data type uchar.
Latter represents a unit of our recieve buffer. Everytime when we write
a value to our recieve buffer we step ahead by 4 units when actually we
wrote to one unit. This results in the loss of 3 bytes out of every 4
bytes recieved. This patch intends to fix this bug.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In a very few cases we need to adjust the driver model root device, such as
when setting it up at initialisation. Add a macro to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want 'N0' and 'n0' to mean the same thing, so ensure that case is not
considered when naming GPIO banks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
The function tps65090_init checks the i2c bus of p->bus. However
the pointer p is not intialiased at this point. Check the local
variable bus instead.
cc: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Simon Glass <sjg@chromium.org>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
To support dcache, we need flush DMA descriptor buffer before enable lcd
DMA.
Also we need call lcd_set_flush_dcache(1) to make lcd driver flush the
lcd buffer if there is any change.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add to code to flush the dcache after we writing in DMA buffer.
Also we need invalidate the dcache before we check the status in the
DMA buffer.
Tested in SAMA5D3x-EK with gmac0. Tftp download speed shows in below:
Disable DCache: 1.1 MiB/s
Enable DCache: 1.6 MiB/s
Increase speed with about 40%.
The code should have no impact with the boards which are not
enable_dcache().
Tested in AT91SAM9M10G45EK.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This also renames the CONFIG_SYS_MACB_xx defines. They are used just local and
therefore don't need the CONFIG_SYS_ prefix.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Cleanup to balance malloc/free calls.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.
Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Most of the warnings seem to be related to using 'int' for size_t. Change
this and fix up the remaining warnings and problems. For bootm, the warning
was masked by others, and there is an actual bug in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Khoronzhuk, Ivan
Tom Rini
Mugunthan V N
Chin Liang See
Sergey Kostanbaev
Axel Lin
J. German Rivera
York Sun
Stephen Warren
Albert ARIBAUD
Ilya Ledvich
Jeroen Hofstee
Yasuhisa Umano
Akshay Saraswat
Simon Glass
Wu, Josh
Andreas Bießmann
Darwin Rambo
Steve Rae