This driver implementes platform specific code for the Xenon SDHCI
controller which is integrated in the Marvell MVEBU Armada 37xx and
Armada 7k / 8K SoCs.
History:
This driver is ported from the Marvell U-Boot version 2015.01 which is
written by Victor Gu <xigu@marvell.com> with minor changes ported from
the Linux driver which is written by Ziji Hu <huziji@marvell.com>.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Some SDHCI drivers might need to do some special controller configuration
after the common clock set_ios() function has been called (speed / width
configuration). This patch adds a call to the newly created function
set_ios_port() when its configured in the host driver.
This will be used by the Xenon SDHCI controller driver used on the
Marvell Armada 3700 and 7k/8k ARM64 SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch completely clears the SDHCI_CLOCK_CONTROL register before the
new value is configured instead of just clearing the 2 bits
SDHCI_CLOCK_CARD_EN and SDHCI_CLOCK_INT_EN. Without this change, some
clock configurations will lead to the "Internal clock never stabilised."
error message on the Xenon SDHCI controller used on the Marvell Armada
3700 and 7k/8k ARM64 SoCs.
The Linux SDHCI core driver also writes 0 to this register before
the new value is configured. So this patch simplifies the driver a bit
and brings the U-Boot driver more in-line with the Linux one.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The read-only-write-enable bit is set by default and must be cleared
to prevent overwriting read-only registers. This should be done
immediately after resetting the PCI Express controller.
Reviewed-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
[York S: Move SYS_FSL_ERRATUM_A007815 to Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
Print the error code for non-zero (failure case) instead
of making debug statement without any condition, this
usually gives proper clue in failure condition.
Log:
The sdhci controller assumes that the base clock frequency is fully supported by
the peripheral and doesn't support hardware limitations. The Linux kernel
distinguishes between base clock (max_clk) of the host controller and maximum
frequency (f_max) of the card interface. Use the same differentiation and allow
the platform to constrain the peripheral interface.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Move all of the status LED feature to drivers/led/Kconfig.
doc/README.LED updated to reflect the Kconfig implementation.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
commit: 65f83802b7 "serial: 16550: Add getfcr accessor"
breaks u-boot commandline working with long commands
sending to the board.
Since the above patch, you have to setup the fcr register.
For board/archs which enable OF_PLATDATA, the new field
fcr in struct ns16550_platdata is not filled with a
default value ...
This leads in not setting up the uarts fifo, which ends
in problems, when you send long commands to u-boots
commandline.
Detected this issue with automated tbot tests on am335x
based shc board.
The error does not popup, if you type commands. You need
to copy&paste a long command to u-boots commandshell
(or send a long command with tbot)
Possible boards/plattforms with problems:
./arch/arm/cpu/arm926ejs/lpc32xx/devices.c
./arch/arm/mach-tegra/board.c
./board/overo/overo.c
./board/quipos/cairo/cairo.c
./board/logicpd/omap3som/omap3logic.c
./board/logicpd/zoom1/zoom1.c
./board/timll/devkit8000/devkit8000.c
./board/lg/sniper/sniper.c
./board/ti/beagle/beagle.c
./drivers/serial/serial_rockchip.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a simple pmic driver for the mc34vr500 pmic which
is used in conjunction with the fsl T1 and LS1 series SoC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to add 'fsl,esdhc' into of_match table to support
driver model for QorIQ eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There would be compiling error as below when enable driver model for esdhc.
undefined reference to `dm_gpio_get_value'
undefined reference to `gpio_request_by_name_nodev'
This patch is to make GPIO support optional with CONFIG_DM_GPIO. Because
all boards of QorIQ platform don't need it and they just check register for
CD/WP status, only some boards of i.MX platform require this.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: York Sun <york.sun@nxp.com>
All Layerscape SoCs have supported new PCIe driver based on DM.
The lagecy PCIe driver code is unused and can be removed.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
There are more than five kinds of Layerscape SoCs. unfortunately,
PCIe controller of each SoC is a little bit different. In order
to avoid too many macro definitions, the patch addes a new
implementation of PCIe driver based on DM. PCIe dts node is
used to describe the difference.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
To make the layerscape pcie driver clear, move the kernel DT fixup
code from pcie_layerscape.c to pcie_layerscape_fixup.c.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
There may be multiple PCIe controllers in a SoC.
It is not correct that always calling pci_bus_to_hose(0) to get
the first PCIe controller for the PCIe device connected other
controllers. We just remove this calling because hose always point
the correct PCIe controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
for the legacy PCI driver, the function pci_bus_to_hose() returns
the real PCIe controller. To keep consistency, this function is
changed to return the PCIe controller pointer of the root bus
instead of the current PCIe bus.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The generic probe code in dm works, so get rid of the leftover cruft.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Revision 1.0 of this IP has a quirk where if during a long read transfer
the transfer_size register will go to 0, the master will send a NACK to
the slave prematurely.
The way to work around this is to reprogram the transfer_size register
mid-transfer when the only the receive fifo is known full, i.e. the I2C
bus is known non-active.
The workaround is based on the implementation in the linux-kernel.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Reorder the timeout loop such that we first check if the
condition is already true, and then call udelay() so if
the condition is already true, break early.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Revision 1.0 of this IP has a couple of issues, such as not supporting
repeated start conditions for read transfers.
So scan through the list of i2c messages for these conditions
and report an error if they are attempted.
This has been fixed for revision 1.4 of the IP, so only report the error
when the IP can really not do it.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
For mux check if the parent is already a device of UCLASS_I2C and if yes
just use that. Otherwise see if someone specified an i2c-parent phandle.
This mimics the behavior found in the Kernel, as it removes the
requirement to explicitly specify a i2c-parent phandle.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
If CONFIG_SYS_I2C_S3C24X0_SLAVE isn't defined, then complie error should
be occurred.
This patch is for preventing it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Latest gcc 6.2 compiler is throwing the below warning for am335x_baltos_defconfig
drivers/usb/gadget/ether.c:501:17: warning: 'mdlm_detail_desc' defined but not used [-Wunused-const-variable=]
static const u8 mdlm_detail_desc[] = {
Guard mdlm_detail_desc with CONFIG_USB_ETH_SUBSET to avoid the warning
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Drop board_ehci_power when dm usb used and switch to use
regulator api to handle vbus.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Implement ofdata_to_platdata to set the type to host or device.
- Check "dr-mode" property.
- If there is no "dr-mode", check phy_ctrl for i.MX6
and phy_status for i.MX7
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
GCC 6.1 complains about this.
drivers/usb/gadget/dwc2_udc_otg.c:72:19: warning: 'driver_desc'
defined but not used [-Wunused-const-variable=]
static const char driver_desc[] = DRIVER_DESC;
^~~~~~~~~~~
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Dropped becuase
- driver not used any board.
- no dm conversion.
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Acked-by: Angelo Dureghello <angelo@sysam.it>
Unfortunately version 2 of this patch was applied which was missing some
changes. Fix this.
Signed-off-by: Meng Yi <meng.yi@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace hardcoded value with defined constant SECTOR_BYTES.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no CONFIG_OF_PLATDATA, only CONFIG_SPL_OF_PLATDATA, so rename
the two references to CONFIG_OF_PLATDATA to CONFIG_SPL_OF_PLATDATA.
Signed-off-by: Tom Rini <trini@konsulko.com>
Dropped becuase
- driver and related configs not used any board.
- no dm conversion.
Cc: Heiko Schocher <hs@denx.de>
Cc: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
If the splash file doesn't exist, the booting stops bricking
the boards. Check return value of prepare function and stop
decoding the logo data if splash prepare stage failed.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Commit f401e907fc ("ARM: sunxi: remove bare default for
CONFIG_MMC") dropped "depends on UART0_PORT_F", but it is still
needed. Revive it as a prerequisite of CONFIG_MMC_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Until recently, sdhci_ops was used only for overriding IO accessors.
(so, host->ops was not set by any drivers except bcm2835_sdhci.c)
Now, we have more optional callbacks, get_cd, set_control_reg, and
set_clock. However, the code
if (host->ops->get_cd)
host->ops->get_cd(host);
... expects host->ops is set for all drivers.
Commit 5e96217f04 ("mmc: pic32_sdhci: move the code to
pic32_sdhci.c") and commit 62226b6863 ("mmc: sdhci: move the
callback function into sdhci_ops") added sdhci_ops for pic32_sdhci.c
and s5p_sdhci.c, but the other drivers still do not (need not) set
host->ops because all callbacks in sdhci_ops are optional.
host->ops must be checked to avoid the system crash caused by NULL
pointer access.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a new driver for the GMAC ethernet interface present in Rockchip
RK3288 SOCs. This driver subclasses the generic design-ware driver to
add the glue needed specifically for Rockchip.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Export all functions so that drivers can use them, or not, as the need
arises.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With rockchip we need to make adjustments after the link speed is set but
before enabling received/transmit. In preparation for this, split these
two pieces into separate functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function can fail, so return the error if there is one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
To allow other DM drivers to subclass the designware driver various
functions and structures need to be exported. Export these.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Init the clock rate to max-frequency from dts with clock driver api.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The variable ret was added but never set as we did not make calls to
other functions that we needed to check the return value on.
Fixes: 505cf4750a ("power: change from meaningless value to error number")
Signed-off-by: Tom Rini <trini@konsulko.com>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_DAVINCI_MMC (renamed to CONFIG_MMC_DAVINCI)
CONFIG_OMAP_HSMMC (renamed to CONFIG_MMC_OMAP_HS)
CONFIG_MXC_MMC (renamed to CONFIG_MMC_MXC)
CONFIG_MXS_MMC (renamed to CONFIG_MMC_MXS)
CONFIG_TEGRA_MMC (renamed to CONFIG_MMC_SDHCI_TEGRA)
CONFIG_SUNXI_MMC (renamed to CONFIG_MMC_SUNXI)
They are the same option names as used in Linux.
This commit was created as follows:
[1] Rename the options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_DAVINCI_MMC/CONFIG_MMC_DAVINCI/g
s/CONFIG_OMAP_HSMMC/CONFIG_MMC_OMAP_HS/g
s/CONFIG_MXC_MMC/CONFIG_MMC_MXC/g
s/CONFIG_MXS_MMC/CONFIG_MMC_MXS/g
s/CONFIG_TEGRA_MMC/CONFIG_MMC_SDHCI_TEGRA/g
s/CONFIG_SUNXI_MMC/CONFIG_MMC_SUNXI/g
'
[2] Commit the changes
[3] Create entries in driver/mmc/Kconfig.
(copied from Linux)
[4] Move the options with the following command
tools/moveconfig.py -y -r HEAD \
MMC_DAVINCI MMC_OMAP_HS MMC_MXC MMC_MXS MMC_SDHCI_TEGRA MMC_SUNXI
[5] Sort and align drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Move (and rename) the following CONFIG options to Kconfig:
CONFIG_EXYNOS_DWMMC (renamed to CONFIG_MMC_DW_EXYNOS)
CONFIG_HIKEY_DWMMC (renamed to CONFIG_MMC_DW_K3)
CONFIG_SOCFPGA_DWMMC (renamed to CONFIG_MMC_DW_SOCFPGA)
The "HIKEY" is a board name, so it is not suitable for the MMC
controller name. I am following the name used in Linux.
This commit was generated as follows:
[1] Rename the config options with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_EXYNOS_DWMMC/CONFIG_MMC_DW_EXYNOS/g
s/CONFIG_HIKEY_DWMMC/CONFIG_MMC_DW_K3/g
s/CONFIG_SOCFPGA_DWMMC/CONFIG_MMC_DW_SOCFPGA/g
'
[2] Commit the changes
[3] Create the entries in drivers/mmc/Kconfig
(with default y for EXYNOS and SOCFPGA)
[4] Run the following:
tools/moveconfig.py -y -r HEAD MMC_DW_EXYNOS MMC_DW_K3 MMC_DW_SOCFPGA
[5] Sort and align drivers/mmc/Makefile for readability
[6] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit was created as follows:
[1] Rename the option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_DWMMC/CONFIG_MMC_DW/g'
[2] create the entry for MMC_DW in drivers/mmc/Kconfig
(the prompt and help were copied from Linux)
[3] run "tools/moveconfig.py -y MMC_DW"
[4] add "depends on MMC_DW" to the MMC_DW_ROCKCHIP entry
[5] Clean-up doc/README.socfpga by hand
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
I am trying to make all DesignWare-based driver options prefixed
with CONFIG_MMC_DW_.
This commit was generated as follows:
find . -name .git -prune -o -type f -print | \
xargs sed -i -e 's/ROCKCHIP_DWMMC/MMC_DW_ROCKCHIP/g'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
'-1' is absolutely meaningless value.
This patch changed from meaningless value to error number.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some MMC drivers describe operations with the DM_MMC_OPS form, but
there are still several drivers with older implementation. We can
not compile drivers from different groups at the same time because
the core framework is shared with #ifdef CONFIG_DM_MMC_OPS.
Every driver should have "depends on DM_MMC_OPS" (or !DM_MMC_OPS)
explicitly to express which framework it is based on. This will
avoid enabling drivers with incompatible interface at the same time.
It is incorrect to make a driver "select DM_MMC_OPS".
While we are here, add "depends on OF_CONTROL" as well because this
driver can be configured only by Device Tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
callback function should be moved into sdhci_ops struct.
Other controller can use these ops for controlling clock or their own
specific register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the s5p_set_clock function.
It's not good that "set_mmc_clk" is assigned directly.
In future, it should be changed to use the clock framework.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This code is used for only pic32_sdhci controller.
To remove the "#ifdef", moves to pic32_sdhci.c.
And use the get_cd callback function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Buswidth is depeneded on Hardware schematic.
Evne though host can support the 8bit buswidth, if hardware doesn't
support 8bit mode, it doesn't work fine.
So the buswidth mode selection leaves a matter in each SoC drivers.
On the contrary to this, hardware supports 8bit mode, but host doesn't
support it. then controller has to disable the MMC_MODE_8BIT.
(Host can check whether 8bit mode is supported or not, since V3.0)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch fixes incorrect pointer on offset device in device tree blob.
When using with the component "Ethernet 1G/2.5G BASE-X PCS/PMA or SGMII"
it does not understand what type is XAE_PHY_TYPE_1000BASE_X and trying
to change frequency.
Signed-off-by: Kamensky Ivan <kamensky.ivan@mail.ru>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adding additional compatible string for version 1.4 of the IP block.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add basic clock driver support for zynqmp which
sets the required clock for GEM controller
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xilinx core files will take care about it.
There is no need to have these functions because they do nothing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These two macros are used for the same thing, the total number of DDR
controllers for a given SoC. Use SYS_NUM_DDR_CTRLS in Kconfig and
merge existing usage.
Signed-off-by: York Sun <york.sun@nxp.com>
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.
Signed-off-by: York Sun <york.sun@nxp.com>
Add option SYS_FSL_ERRATUM_ESDHC111, SYS_FSL_ERRATUM_ESDHC13,
SYS_FSL_ERRATUM_ESDHC135, SYS_FSL_ERRATUM_ESDHC_A001 to mmc Kconfig.
Move existing macros to related Kconfig.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate bk4r1]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.
Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.
Signed-off-by: York Sun <york.sun@nxp.com>
SPL from nand will print 'NAND' in boot_from_devices based on
the image_loader name, remove the extra 'NAND ' in mxs_nand_spl driver.
Original behaviour:
-------------------
U-Boot SPL 2017.01-rc2-gf84dd8b (Jan 02 2017 - 22:24:19)
Trying to boot from NANDNAND : 512 MiB
After the fix:
-------------
U-Boot SPL 2017.01-rc2-gf84dd8b-dirty (Jan 02 2017 - 23:17:00)
Trying to boot from NAND: 512 MiB
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
According to Section 11.15.4.9.1 Indirect Read Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface reads until the last word of an indirect transfer
So, make sure that QSPI indirect reads are 32 bit sized except for the
final read. If the rxbuf is unaligned then use bounce buffer, so that
readsl() can be used instead of readsb() to avoid non 32-bit accesses.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC
TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit
data interface writes until the last word of an indirect transfer
otherwise indirect writes is known to fails sometimes. So, make sure
that QSPI indirect writes are 32 bit sized except for the last write. If
the txbuf is unaligned then use bounce buffer to avoid data aborts.
So, now that the driver uses bounce_buffer, enable CONFIG_BOUNCE_BUFFER
for all boards that use Cadence QSPI driver.
[1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Fix 'driver model' rather than 'driver mode' in description.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is a user-unconfigurable option that is selected by the
drivers that need to overwrite SDHCI IO memory accessors.
(BCM2835 SDHCI seems the only driver that needs to do so.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While I moved the options, I also renamed them so that they are all
prefixed with MMC_SDHCI_.
This commit was created in the following steps.
[1] Rename with the following command
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e '
s/CONFIG_MMC_SDMA/CONFIG_MMC_SDHCI_SDMA/g
s/CONFIG_BCM2835_SDHCI/CONFIG_MMC_SDHCI_BCM2835/g
s/CONFIG_KONA_SDHCI/CONFIG_MMC_SDHCI_KONA/g
s/CONFIG_MV_SDHCI/CONFIG_MMC_SDHCI_MV/g
s/CONFIG_S5P_SDHCI/CONFIG_MMC_SDHCI_S5P/g
s/CONFIG_SPEAR_SDHCI/CONFIG_MMC_SDHCI_SPEAR/g
'
[2] create the Kconfig entries in drivers/mmc/Kconfig
[3] Move the options by the following command
tools/moveconfig.py -y MMC_SDHCI_SDMA MMC_SDHCI_BCM2835 \
MMC_SDHCI_KONA MMC_SDHCI_MV MMC_SDHCI_S5P MMC_SDHCI_SPEAR
[4] Sort drivers/mmc/Makefile for readability
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Move CONFIG_SDHCI to Kconfig and rename it to CONFIG_MMC_SDHCI.
My motivation for the rename is, ultimately, to make all the MMC
options prefixed with MMC_ and SDHCI options with MMC_SDHCI_,
like Linux.
This commit was created as follows:
[1] Rename the config option with the following command:
find . -name .git -prune -o ! -path ./scripts/config_whitelist.txt \
-type f -print | xargs sed -i -e 's/CONFIG_SDHCI/CONFIG_MMC_SDHCI/g'
[2] create the entry for MMC_SDHCI in drivers/mmc/Kconfig
[3] run "tools/moveconfig.py -y MMC_SDHCI"
[4] add "depends on MMC_SDHCI" to existing SDHCI driver entries
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently, CONFIG_MMC is not related to any other options by
"depends on" or "select". One of big advantages of using Kconfig
is automatic dependency tracking, but the current state is lacking
it. As the first step, make the existing MMC driver entries depend
on MMC.
This commit was created by the following steps:
[1] Run the following script:
--------------------8<--------------------
rm -f tmp.txt
for d in $(find . -path './configs/*_defconfig')
do
if grep -q -e 'CONFIG_MSM_SDHCI=y' $d ||
grep -q -e 'CONFIG_ATMEL_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_DWMMC=y' $d ||
grep -q -e 'CONFIG_SH_SDHI=y' $d ||
grep -q -e 'CONFIG_PIC32_SDHCI=y' $d ||
grep -q -e 'CONFIG_ZYNQ_SDHCI=y' $d ||
grep -q -e 'CONFIG_ROCKCHIP_SDHCI=y' $d ||
grep -q -e 'CONFIG_MMC_UNIPHIER=y' $d ||
grep -q -e 'CONFIG_SANDBOX_MMC=y' $d
then
echo CONFIG_MMC=y >> $d
echo ${d#./configs/} >> tmp.txt
fi
done
tools/moveconfig.py -y -s -d tmp.txt
rm tmp.txt
--------------------8<--------------------
[2] surround MMC driver entries with "if MMC" and "endif"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 7a777f6d6f ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c798799f ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.
We generally do not like such partial moves. This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.
I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.
This commit was created as follows:
[1] Edit Kconfig (remove the "depends on", add the "default",
copy the prompt and help message from Linux)
[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
Earlier timer driver needed a clock-frequency property in compatible
device-tree nodes. Another way is to reference a clock via a phandle.
So now timer_pre_probe tries to get clock by reference through device
tree. In case it is impossible to get clock device through the
reference, clock-frequency property of the timer node is read to provide
backward compatibility.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support to handle enable-active-high DT property. This property is
used to drive the gpio controlling fixed regulator as active high when
claiming gpio line.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add the max8998 controller for Driver model.
Samsung S5P series are using max8998 pmic controller.
In future, it should be supported the regulator framework.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Remove the entire spear_sdhci.c file.
There is no use case. This is dead codes.
Also there is no place to call "spear_sdhci_init()" anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
armada100_spi.c and related env is zapping becuase
of "no DM conversion".
Cc: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Jagan Teki <jagan@openedev.com>
armada100_spi.c, related config options and related codes
are zapping becuase of "no DM conversion".
Cc: Werner Pfister <Pfister_Werner@intercontrol.de>
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch also includes ARM64 zynqmp changes:
- Remove platform non DM initialization
- Remove hardcoded sata base address
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All sata based drivers are bind and corresponding block
device is created. Based on this find_scsi_device() is able
to get back block device based on scsi_curr_dev pointer.
intr_scsi() is commented now but it can be replaced by calling
find_scsi_device() and scsi_scan().
scsi_dev_desc[] is commented out but common/scsi.c heavily depends on
it. That's why CONFIG_SYS_SCSI_MAX_DEVICE is hardcoded to 1 and symbol
is reassigned to a block description allocated by uclass.
There is only one block description by device now but it doesn't need to
be correct when more devices are present.
scsi_bind() ensures corresponding block device creation.
uclass post_probe (scsi_post_probe()) is doing low level init.
SCSI/SATA DM based drivers requires to have 64bit base address as
the first entry in platform data structure to setup mmio_base.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add compatibility string for the Ingenic JZ4780 SoC, the necessary
UART enable bit into FCR and register shift. Neither are encoded
in the DTS coming from Linux, so we need to support it this way.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver data to each compatible string to identify the type of
the port. Since all the ports in the driver are entirely compatible
with 16550 for now, all are marked with PORT_NS16550. But, there
are ports which have specific quirks, like the JZ4780 UART, which
do not have any DT property to denote the quirks. Instead, Linux
uses the compatible string to discern such ports and enable the
necessary quirks.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Add function which allows fetching the default FCR register setting
from platform data for DM , while retaining old behavior for non-DM
by returning UART_FCRVAL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
0c0f719ad2 accidentally changed the
endianness of the i2c read and write addresses. This was noticable when
accessing EEPROMs that use 2 byte addressing as the LSB was being sent
first.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some I2C bus devicetree nodes, doesn't require to have
gpio pinctrl so replace the dev_info to debug so the
print never comes on the console and for bus that uses
gpio pinctrl anyway have dev_err.
Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.
After:
------
U-Boot> i2c dev 1
Setting bus to 1
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
Better to print the hex value for bus address instead of
decimal, for more readbility on bus addressing.
Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 35274752, no gpio pinctrl state.
After:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
- Remove exctra space
- Add space
- Add tab space
- Fix single line comments quotes
- Fix 'CHECK: Avoid CamelCase'
- Fix 'CHECK: Alignment should match open parenthesis'
- Fix 'WARNING: line over 80 characters'
- Re-arrage header include files
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch add driver model support for fec_mxc driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
fec_get_hwaddr never used eth_device argument, hence removed.
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.
The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
There two iomuxc for i.MX6SLL. One is normal IOMUXC, the other
is for IOMUXC_SNVS.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the i.MX6SLL support to OCOTP driver.
The i.MX6SLL reuses the i.MX6ULL fuse, bank 7 and bank8 have 4 words
each, and there is a hole between bank 5 and bank 6.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
LS2080A SoC family has QBMAN ver 4.0 whereas newer
SoCs like LS2088A, LS1088A has QBMAN ver 4.1
QBMAN ver 4.0 and ver 4.1 supports dqrr size as 4 and 8 respectively.
Add support of
to check QBMAN version based on SoC SVR
update dqrr_size accordingly
update code to support larger dqrr_size
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This reverts commit c56ae7519f.
Once the 'Quad Enable' bit is cleared in their Enhanced Volatile
Configuration Register (EVCR), Micron memories expect ALL commands to use
the SPI 4-4-4 protocol. Commands using SPI 1-y-z protocols are no longer
accepted.
Within the reverted commit, the write_evcr() function is implemented using
the spi_flash_write_common(), which is a shortcut for the
[ spi_flash_cmd_write_enable(), spi_flash_cmd_write(),
spi_flash_cmd_wait_ready() ] sequence.
Since the internal state of the Micron memory has been changed when the
spi_flash_cmd_write() function completes, the later call of the
spi_flash_cmd_wait_ready() function fails.
Indeed the SPI controller driver is not aware of the SPI protocol switch.
Further patches will fix the support of Micron QSPI memories.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[Rebase on master, use JEDEC_MFR(info) in place of idcode0]
Signed-off-by: Jagan Teki <jagan@openedev.com>
As long as the memory mapped size specifeid in the DT is the same or
bigger than the device size, it will work. So do not force the sizes
to be identical.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In spi_flash_scan, 'ret' is initialled to -1, but 'ret' is not always
used to store a return value, in that case, even when the function
succeed, an error (-1) will be returned.
Lets just return 0 if we hit the end of the function.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Move the code to read the "sram-size" property into the other code
that reads properties from the node, rather than the SF subnode.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Cadence QSPI controller has specified overheads for the various CS
times that are in addition to those programmed in to the Device Delay
register. The overheads are different for the delays.
In addition, the existing code does not handle the case when the delay
is less than a SCLK period.
This change accurately calculates the additional delays in Ref clocks.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Instead of extracting mode settings and passing them as separate
args to another function, just pass the SPI mode as an arg.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tom Rini
Simon Glass
Stefan Roese
Tony O'Brien
Jagan Teki
Stefan Herbrechtsmeier
Masahiro Yamada
Uri Mashiach
Heiko Schocher
Yangbo Lu
Hou Zhiqiang
Minghuan Lian
Moritz Fischer
Jaehoon Chung
Lokesh Vutla
Peng Fan
Michal Simek
Jagan Teki
Meng Yi
Ladislav Michl
Anatolij Gustschin
Sjoerd Simons
Nickey Yang Nickey Yang
Kever Yang
Kamensky Ivan
Siva Durga Prasad Paladugu
Mugunthan V N
York Sun
Vignesh R
Priit Laes
Marcel Ziswiler
Ajay Bhargav
Zakharov Vlad
Marek Vasut
Bradley Bolen
Jagan Teki
Patrick Bruenn
Priyanka Jain
Cyrille Pitchen
Phil Edworthy
Fabien Parent