Remove the security peripheral select code, keep the default value
in these registers, that is, the peripheral address space is
configured as "Secured" access, it is suitable for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
On processor reset, the matrix write protection is disabled,
so no need to disable/enable write protection when writing
the matrix registers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To make the matrix initialization code sharing with other SoCs,
move it from SAMA5D4 particular file,
mach-at91/armv7/sama5d4_devices.c to a separate file,
mach-at91/matrix.c
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The early MMU table doesn't enable all addresses. Unused addresses
are marked as invalid, as introduced by commit 9979922. An entry
was missing for NAND flash space, causing nand boot failure.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
If the core runs at higher than x3 speed of the platform, there is
possiblity about sev instruction to getting missed by other cores.
This is because of SoC Run Control block may not able to sample
the EVENTI(Sev) signals.
Configure Run Control and EPU to periodically send out EVENTI signals to
wake up A57 cores.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When one core is released, other cores may not have valid entry
address. Those cores are trapped by "wfe" and wait for further
instruction. When their address is set, they need to be kicked
off by "sev".
Signed-off-by: York Sun <yorksun@freescale.com>
For most device addresses excution shouldn't be allowed. Revise
the MMU table to enforce execute-never bits. OCRAM, DDR and IFC
are allowed for excution.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reported-by: Zhichun Hua <zhichun.hua@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
Reuse dts files from ls1043a linux kernel. Some parts in dts files
may not be needed by U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The global_data pointer (gd) has been set earlier in crt0_64.S.
So there's no need to assign it again. Remove gdata since it is going
away in U-Boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The endian and base address of PEX LUT register region is different
between Chassis 2 and Chassis 3, so move the base address definition
to chassis specific header file and add pex_lut_* functions to access
LUT register.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.
Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot,but the problem was mysteriously related to the toolchain
used for building u-boot.Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value.This causes the timer compare to fire 344 seconds
after u-boot configures it.Depending on how fast u-boot gets the
kernel booted,this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
To fix the above issue, the generic physical timer is disabled
before jumping to the OS.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch addresses a problem mentioned recently on this mailing list:
[1].
In that posting a LS1021 based system was locking up at about 5 minutes
after boot, but the problem was mysteriously related to the toolchain
used for building u-boot. Debugging the problem reveals a stuck
interrupt 29 on the GIC.
It appears Freescale's LS1021 support in u-boot erroneously sets the
64-bit ARM generic PL1 physical time CompareValue register to all-ones
with a 32-bit value. This causes the timer compare to fire 344 seconds
after u-boot configures it. Depending on how fast u-boot gets the
kernel booted, this amounts to about 5-minutes of Linux uptime before
locking up.
Apparently the bug is masked by some toolchains. Perhaps this is
explained by default compiler options, word sizes, or binutils versions.
At any rate this patch makes the manipulation explicitly 64-bit which
alleviates the issue.
[1]
https://lists.yoctoproject.org/pipermail/meta-freescale/2015-June/014400.html
Signed-off-by: Chris Kilgour <techie@whiterocker.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board was constantly parasiting on the CV SoCDK, so split it
into it's own separate directory. Moreover, the board config was
missing important bits, like simple-bus support in SPL, the DRAM
configuration was incorrect and the DTS was also missing the pre
reloc bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Jan Viktorin <viktorin@rehivetech.com>
When adding support for the Arria10 platform, we're going to name the file
base_addr_a10.h, so to be systematic about it, rename the socfpga_base_addr.h
to be base_addr_ac5.h for the Arria5 and Cyclone5 platform.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The Cyclone V Hard Processor System Technical Reference Manual in the
chapter about the Reset Manager Module Address Map stats that the offset
of the tstscratch register ist 0x54 not 0x24.
Cyclone V Hard Processor System Technical Reference Manual cv_5v4 2015.11.02
page 3-17 Reset Manager Module Address Map
Signed-off-by: Philipp Rosenberger <ilu@linutronix.de>
This patch add ZyXEL NSA310S 1-Bay Media Server
The ZyXEL NSA310S device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1000Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 4 Status LED (green)
- 1 Copy/Sync button
- 1 Reset button
- 1 SATA II port
- 2 USB 2.0 ports (front and back)
- Smart fan
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
As some MVEBU platforms using the MVNETA driver seem to miss the
first ARP packet, lets reduce the timeout and increase the retry
count. This increases the speed for communication establishment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
On mx6sx, the CCM register bits for GPMI are different as other
mx6 platforms. Modify the GPMI clock function to support mx6sx.
Signed-off-by: Ye.Li <B37916@freescale.com>
We should also take MX6D option in consideration when defining
imx_iomux_v3_setup_pad().
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.
Add SPL support so that all the variants can be supported
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().
Tested on AM437x IDK EVM with QSPI XIP boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These files are based on the current latest upstream kernel work. The
bus_gates bindings may still change, but for u-boot that does not matter
as we do not (yet) use any clock info from devicetree for sunxi u-boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Unify serial_tegra, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_rockchip, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
Adjust the cros_ec keyboard driver to support driver model. Make this the
default for all Exynos boards so that those that use a keyboard will build
correctly with this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the tegra keyboard driver to support driver model, using the new
uclass. Make this the default for all Tegra boards so that those that use
a keyboard will build correctly with this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put jump trampoline to TCM at 0 and setup R5 reset address to 0.
Jump trampoline ensures that jump to the right location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.
Make SPL take into account the correct mmc device.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it. Also, allow the board to only specify the lanes that are
used instead of including unused lanes.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Functions that do not modify the pointer passed should declare it
as const.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Compile misc.c for mx7, since we need related function for
lcdif and nand.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Need to call lcdif_power_down to make lcdif in initial state
before kernel boot. Similar issue for uboot reset with lcdif
enabled, system will hang after serveral times resetting. Need
to let lcdif initial state to make all go well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
We need to power down lcdif before uboot reset to make reset can pass
stress test.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Introudce a new function lcdif_power_down.
1. Waits for a VSYNC interrupt to guarantee the reset is done at the
VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?)
and helps the LCDIF work normally at the kernel stage.
2. Add power down function to stop lcdif.
The reason to introduce lcdif_power_down is that we want lcdif to be in
initial state when doing uboot reset or before kernel boot to make
system stable, otherwise system may hang.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
1. Move WDOG3_BASE_ADDR to '#if !(defined(__ASSEMBLY__))'.
2. Add i.MX6UL LCDIF register base address. And Introduce
LCDIF1_BASE_ADDR to support runtime check.
3. include <asm/imx-common/regs-lcdif.h> for imx-regs.h to avoid
building error for mxsfb.c, since mxsfb.c use imx-regs.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Share one lcdif structure for i.MXes.
1. Discard struct mxs_lcdif_regs from imx-regs.h of i.MX7
2. Add i.MX6SX/6UL/7D support in imx-lcdif.h of imx-common
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Move 'struct mxs_lcdif_regs' and lcdif related macro definitions to
arch/arm/include/asm/imx-common/regs-lcdif.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
There are uint8_t, uint32_t types in regs-common.h, so include
linux/types.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Change mxs_set_lcdclk prototype to add a new parameter
base_addr. There are two LCD interfaces for i.MX6SX,
we may support LCDIF1 or LCDIF2.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The code such as PSCI in section named secure is bundled with
u-boot image, and when bootm, the code will be copied to their
runtime address same to compliation/linking address -
CONFIG_ARMV7_SECURE_BASE.
When compile the PSCI code and link it into the u-boot image,
there will be relocation entries in .rel.dyn section for PSCI.
Actually, we do not needs these relocation entries.
If still keep the relocation entries in .rel.dyn section,
r0 at line 103 and 106 in arch/arm/lib/relocate.S may be an invalid
address which may not support read/write for one SoC.
102 /* relative fix: increase location by offset */
103 add r0, r0, r4
104 ldr r1, [r0]
105 add r1, r1, r4
106 str r1, [r0]
So discard them to avoid touching the relocation entry in
arch/arm/lib/relocate.S.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
p2371-2180 is the engineering board name for the Jetson TX1 developer
kit. Update Kconfig description and help text to make this obvious to
everyone.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename GPU functions to less generic names to avoid potential name
collisions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no justification for this function, especially in exported
form.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to detect timeouts when waiting for HW events such as PLL
lock done. Any errors are logged and trigger an error return code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the tables defining which pads and mux options exist in the Tegra210
XUSB padctl hardware.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This change simply deletes code from the Tegra210 XUSB padctl driver that
is already present in the common XUSB padctl code. Since all the arrays
in tegra210_socdata are empty, this update may leave the Tegra210 XUSB
padctl driver non-functional at run-time. However, (a) this driver is not
used yet so no regression can be observed and (b) the next commit will
immediately fix this up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are some differences between the Tegra124 and Tegra210 XUSB padctl
code. So far, the common XUSB padctl code only supports Tegra124. Add
some parameters etc. so that it can work for both chips.
This also allows moving Tegra124's process_nodes() into the common file;
something that would have requires edits during the move if done in the
previous commit.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A fair amount of the XUSB padctl driver will be common between Tegra124
and Tegra210. To avoid cut/paste between the two chips, create a new
file that will contain the common code, and convert the Tegra124 code to
use it. This change doesn't move every last piece of code that can/will be
shared, but rather concentrates on moving code that can be moved with zero
changes, so there are no other diffs mixed in.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This file defines pr_fmt(), so the individual error() calls don't need to
include the prefix in their format strings. Doing so results in duplicate
text in any error messages. Remove the duplication.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A future patch will soon move some of the XUSB padctl code into a common
file in arch/arm/mach-tegra. Rename the existing dummy XUSB padctl file
to avoid conflicting with that, or being confusing.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra210's PCI controller is largely identical to Tegra124, and hence
shares the same binding. However, it has a unique compatible value due
to the existence of at least one new HW bug that would prevent any driver
for a previous HW version from operating correctly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement the procedure that the TRM mandates to initialize PLLREFE and
PLLE. This makes the PLL actually lock.
Note that this section of the TRM is being cleaned up to remove some
confusion. The set of register accesses in this patch should be final,
although the step numbers/descriptions might still change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The latest Linux can directly handle SMP operations for UniPhier SoCs
without any help of U-boot. Drop the relevant code from U-boot.
See commit b1e4006aeda8c8784029de17d47987c21ea75f6d ("ARM: uniphier:
rework SMP operations to use trampoline code") in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This makes USB3.0 available on new SoCs/boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The IRQ is not used in U-Boot, but this would be useful to sync
device trees between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This sets up a fine-grained page table, which is a requirement for
noncached_init() to operate correctly.
MMU setup code currently exists in a number of places:
- A version in the core ARMv8 support code that sets up page tables that
use very large block sizes that CONFIG_SYS_NONCACHED_MEMORY doesn't
support.
- Enhanced versions for fsl-lsch3 and zynmq that set up finer grained
page tables.
Ideally, rather than duplicating the MMU setup code yet again this patch
would instead consolidate all the different routines into the core ARMv8
code so that it supported all use-cases. However, this will require
significant effort since there appear to be a number of discrepancies[1]
between different versions of the code, and between the defines/values by
some copies of the MMU setup code use and the architectural MMU
documentation. Some reverse engineering will be required to determine the
intent of the current code.
[1] For example, in the core ARMv8 MMU setup code, three defines named
TCR_EL[123]_IPS_BITS exist, but only one of them sets the IPS field and
the others set a different field (T1SZ) in the page tables. As far as I
can tell so far, there should be no need to set different values per
exception level nor to modify the T1SZ field at all, since TTBR1 shouldn't
be enabled anyway. Another example is inconsistent values for *_VA_BITS
between the current core ARMv8 MMU setup code and the various SoC-
specific MMU setup code. Another example is that asm/armv8/mmu.h's value
for SECTION_SHIFT doesn't match asm/system.h's MMU_SECTION_SHIFT;
research is needed to determine which code relies on which of those
values and why, and whether fixing the incorrect value will cause any
regression.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
In order for noncached_init() to operate correctly, SoCs must set up a
custom page table with fine-grained (2MiB) sections, which can be
configured from noncached_init().
This is currently performed by arch/arm/cpu/armv8/{fsl-lsch3,zynqmp}/cpu.c
by cut/pasting and re-implementing mmu_setup, enable_caches(), etc. There
are some other reasons for the duplication there though, such as enabling
icache early, and enabling dcaching earlier with a different configuration.
This change makes mmu_setup() a weak implementation, so that the MMU setup
code can be replaced without having to duplicate other code that calls it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The implementation of noncached_init() uses define MMU_SECTION_SIZE.
Define this on ARM64.
Move the prototype of noncached_{init,alloc}() to a location that
doesn't depend on !defined(CONFIG_ARM64).
Note that noncached_init() calls mmu_set_region_dcache_behaviour() which
relies on something having set up translation tables with 2MB block size.
The core ARMv8 MMU setup code does not do this by default, but currently
relies on SoC specific MMU setup code. Be aware of this before enabling
this feature on your platform!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Old sector number is not being cleared from FLASH_CR register. For example
when first erased sector was 001 and then you want to erase sector 010,
sector 011 gets erased instead.
This patch clears old sector number from FLASH_CR register before a new
one is written.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
flash_lock call is inside a for loop, so after the first iteration flash
is locked and no more sectors can be erased.
Move flash_lock out of the loop.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Kirkwood files cpu.c and cache.c cannot build in Thumb state;
force them in ARM state even under CONFIG_SYS_THUMB_BUILD.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
When building a Thumb-1-only target with CONFIG_SYS_THUMB_BUILD,
some files fail to build, most of the time because they include
mcr instructions, which only exist for Thumb-2.
This patch introduces a Kconfig option CONFIG_THUMB2 and uses
it to select between Thumb-2 and ARM mode for the aforementioned
files.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch fixes compile warnings like this:
warning: format '%lu' expects argument of type 'long unsigned int',
but argument 5 has type 'size_t'
In C99 standard you can use %zu modifier to print size_t values.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
If you enable CONFIG_SEMIHOSTING for STM32F429 target, you will get compile
error looking like this:
arch/arm/lib/semihosting.c: In function 'smh_read':
{standard input}: Assembler messages:
{standard input}:34: Error: invalid swi expression
{standard input}:34: Error: value of 1193046 too large for field of 2 bytes at 0
scripts/Makefile.build:277: recipe for target 'arch/arm/lib/semihosting.o' failed
The source of the problem is "svc #0x123456" instruction. This instruction
can not be encoded using Thumb2 instruction set used by ARMv7M CPUs.
ARM documentation suggests using "bkpt #0xAB" instruction instead [1].
This patch fixes compile errors and adds support for semihosting for
STM32F429 or any other ARMv7M target.
This change was sested on STM32F429-DISCOVERY board using OpenOCD and
"smhload" u-boot command.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0471c/Bgbjhiea.html
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
This patch fix compilation error:
drivers/mmc/zynq_sdhci.c:16:5: error: conflicting types for
‘zynq_sdhci_init’
int zynq_sdhci_init(phys_addr_t regbase)
^
In file included from drivers/mmc/zynq_sdhci.c:14:0:
./arch/arm/include/asm/arch/sys_proto.h:16:5: note: previous declaration
of ‘zynq_sdhci_init’ was here
int zynq_sdhci_init(unsigned long regbase);
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
With a working QSPI calibration, the SCLK can now run up to 100MHz
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Update this driver to use driver model and change all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPI requires DM and OF that's why enable DM for ZynqMP
and start to use configuration based on embedded OF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to mark some device tree nodes so that they are available before
relocation. This enables driver model to find these automatically. In the
case of SPL it ensures that these nodes will be retained in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move to using device tree control in SPL so that we can use the same driver
code in both SPL and U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the debug UART to assist with early debugging. Enable it
for Zybo as an example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move to the new way of starting up SPL. Clearing of BSS and calling
board_init_r() is now handled by crt0.S.
Also tidy up the header include order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DMA, QSPI, and SD/MMC reset bits are located in the permodrst register,
not the mpumodrst. So the bank for these reset bits should be 1, not 0.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some peripherals may need a second clock source that may be different
from the system clock. This second clock is the generated clock (GCK)
and is managed by the PMC via PMC_PCR.
For simplicity, the clock source of the GCK is fixed to PLLA_CLK.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Provide the specific addresses for the Chip ID and Chip ID Extension
registers, instead of the offset, which make it use on other chips.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch will fix these checkpatch issues.
ERROR: Macros with complex values should be enclosed in parentheses
+#define DEFAULT_DQS_X4 (DEFAULT_DQS << 24) || (DEFAULT_DQS << 16) \
+ || (DEFAULT_DQS << 8) || (DEFAULT_DQS << 0)
ERROR: space prohibited before that ',' (ctx:WxW)
+ writel(val , &drex0->concontrol);
^
ERROR: space prohibited before that ',' (ctx:WxW)
+ writel(val , &drex1->concontrol);
^
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There are 8 pins for SD card in Exynos, but the MUX was configured
only for 7, since the one was used for card detection.
This caused the pin's pull wrong configuration.
This commit fixes this and the card detect can work properly,
after call this function.
Tested-on: Odroid U3 and Odroid X2.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This ADC is required for Odroid's board revision detection.
The pre-reloc request is enabled, since board detection will
be done in one of early function call.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adds common ADC node, which is disabled as default.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adds driver for Exynos54xx ADC subsystem.
The driver is implemented using driver model, amd provides
ADC uclass's methods for ADC single channel operations:
- adc_start_channel()
- adc_channel_data()
- adc_stop()
The basic parameters of ADC conversion, are:
- sample rate: 600KSPS
- output the data as average of 8 time conversion
ADC features:
- sample rate: 600KSPS
- resolution: 12-bit
- channels: 10 (analog multiplexer)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The proper CPU ID for those Exynos variants is 0x5422,
but before the 0x5800 was set. This commit fix this back.
Changes:
- set cpu id to 0x5422 instead of 0x5800
- remove macro proid_is_exynos5800()
- add macro proid_is_exynos5422()
- change the calls to proid_is_exynos5800() with new macro
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This platform is based on Exynos5800 but the cpu id is 0x5422.
This doesn't fit the common Exynos SoC name convention, so now,
the CPU name is defined by device tree string, to be printed
properly.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CPU name for Exynos was concatenated with cpu id,
but for new Exynos platforms, like Chromebook Peach Pi
based on Exynos5800, the name of SoC variant does not
include the real SoC cpu id (0x5422).
For such case, the CPU name should be defined in device tree.
This commit introduces new device-tree property for Exynos:
- "cpu-model" - with cpu name string
If defined, then the cpu id is not printed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
crt0.S do both memset the bss section and call board_init_r for us, so
remove them from board_init_f().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add mx7 secure boot support, add helper macro IS_HAB_ENABLED_BIT
to get the corresponding bit mask per SoC (mx7 or mx6) to identify
if securue boot feature is enabled/disabled.
On authenticate_image only check for mmu enabled on mx6 SoC to
force pu_irom_mmu_enabled so ROM code can perform mmu cache flush
mx7 SoC ROM code does not have this issue as ROM enables cache support
based on fuse settings.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add secure boot fuse helper struct to abstract the way
to find out secure boot settings per SoC iMX family
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework unified section macro select via Kconfig option
instead of macro definition in mx7_common header file.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add CONFIG_ROM_UNIFIED_SECTIONS for mx6sx and mx6ul target
platforms to resolve corresponding HAB_RVT_BASE base address,
the RVT table contains pointers to the HAB API functions in
ROM code.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Rework secure boot support for imx6, move existing hab support
for imx6 into imx-common for SoC reuse.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Move common chip revision id's to main cpu header file
mx25 generic include cpu header for chip revision
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
We can reuse common functions in lib/time.c, but not reimplement
functions in imx-common/time.c.
Only keep timer_init ,get_tbclk and implement timer_read_counter in
imx-common/time.c.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Freescale ARM-based Layerscape LS102xA contain a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls1021aqds and ls1021atwr boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to
make secondary cores excute in spin loop.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Freescale LayerScape with Chassis Generation 2 is a set of SoCs with
ARMv8 cores and 2rd generation of Chassis.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable snooping for CAAM read & write transactions by
programming the SCFG snoop configuration register:
SCFG_SNPCNFGCR[SECRDSNP]
SCFG_SNPCNFGCR[SECWRSNP]
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Data types and I/O functions have been defined for
64 bit physical addresses in arm.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As QSPI/DSPI and IFC are pin multiplexed, IFC is disabled
in SD boot for QSPI. This patch will add fdt support for
this rule.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Pointer 'reg' returned from call to function 'fdt_getprop' may be
NULL, will be passed to function and may be dereferenced there by
passing argument 1 to function 'of_read_number'. So check pointer
'reg' first.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enabled zynq qspi controller node for microzed board,
verified the same on spansion spi-nor flash.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We should not init the console this early since it precludes using driver
model for the UART, since it is not set up at the start of board_init_f().
See the README for more information. The debug UART does not have this
restriction. If we want to do early init with the console on it can be done
in spl_board_init().
Move the preloader_console_init() call from board_init_f() to board_init_r().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is quite a bit of assembler code that can be removed if we use the
generic global_data setup. Less arch-specific code makes it easier to add
new features and maintain the start-up code.
Drop the unneeded code and adjust the hooks in board_f.c to cope.
Tested on LS2085ARDB and LS2085AQDS (armv8 SoC).
Tested-by: York Sun <yorksun@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Import various DT files for am57xx-beagle-x15 from
Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO,
DM_SERIAL and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Import various DT files for am437x-sk-evm from Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO, DM_SERIAL
and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Import various DT files for am4372, an43xx pinctrl and
am437x-gp-evm from Linux Kernel v4.2
Add config file for this board, enable DM, DM_GPIO, DM_SERIAL
and DM_MMC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Existing driver gets the actual omap hammc base address + 0x100
bytes as the first 0x100 bytes is not used by the driver. But
with DM conversion the base address from DT is different, to
accommodate the offset adding res0[0x100] to struct hsmmc.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import various DT files for dra7-evm from Linux Kernel v4.2
Add config file for this board, enable DM and DM_GPIO
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MMC support for k2g
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
In K2G, Ethernet doesn't support SGMII instead it support RGMII,
adding support to the driver to connect to RGMII phy.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
update K2G nav rx queue number
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add clock information for Galileo
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Keystone dts files assumes that LPAE is enabled and top level root
node uses 64bit addresses. This breaks the keystone boot with
CONFIG_OF_CONTROL enabled. So do not use 64 bit addresse in U-Boot DT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Import various generic dts files from Linux kernel so that
all keystone2 platforms can be DT in U-boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With CONFIG_DM_SERIAL is enabled NS16550_init() cannot be
called directly. Driver probe should be taking care of this.
So call this function only when DM_SERIAL is not enabled.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since there is a common function to grab the serial number from the die id bits,
it makes sense have one to parse that serial number and feed it to the serial
ATAG.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces omap4 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces the previous get_dieid definition with omap_die_id, that matches
the common omap_die_id definition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This introduces a common definition for omap_die_id, that aims at providing a
common interface for accessing omap platform's die id bits.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables DM_SERIAL for all ARCH_MVEBU boards (AXP & A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds driver model support for some Marvell MVEBU SoC's. Including
Armada XP and 38x. All 3 currently mainlined boards are converted. DM is now
selected automatically for MVEBU platforms.
With this DM support now available for MVEBU, hardcoding the base addresses
and other information is not necessary any more. Probing should be done
by using the values provided via the device tree now instead. For this
the driver also need to be converted to DM. Patches for some of the drivers
will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
These will be needed by the upcoming DM (driver model) support for
the Armada XP / 38x SoC's. This will provide DT based probing.
The dts files are copied 1:1 from the Linux kernel release v4.2.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the MVEBU SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the use of the kwboot tool, to boot mainline U-Boot
on the Marvell Armada XP/38x SoC's. This is done by returning to the
SoC's BootROM after SPL has initialized the SDRAM. We need to make sure
to not reconfigure the internal register space and MBARs. Otherwise
the BootROM will not be able to continue after SPL jumps back to it.
To use this feature, please don't forget to change the BOOT_FROM line
in your board specfic kwbimage.cfg file this way:
BOOT_FROM uart
Tested on these Marvell eval boards:
DB-MV784MP-GP - Armada XP
DB-88F6820-GP - Armada 38x
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
The DT is identical to the DT submitted to the upstream kernel.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Linux had a number of changes to the AXP209 DTSI. Sync ours.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add the latest kernel changes to the sun5i family DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
So far, even if CONFIG_MMC was not enabled the board code was trying to use
the MMC-related functions, resulting in linker errors.
Protect those calls by an ifdef.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
The dts changes are identical to the dts files submitted upstream.
A few notes on the use if dldo and aldo regulators. DLDO1 is used
for Vdd for the ethernet phy, ALDO2 is used for AVdd for the ethernet
phy. ALDO1 is used to power the sdio wifi module.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We now have generic q8_a?3_defconfig files for Q8 formfactor tablets with
an A13 / A23 / A33 SoC, there is no need for these PCB variant specific
defconfig-s and they only serve to confuse the user.
Note that in case of the forfun_q88db_defconfig and TZX-Q8-713B7_defconfig
for A13 based Q8 tablets there is not even a dts file for these in the
upstream kernel, which is all the more reason to remove them.
The generic q8_a?3_defconfig files have been tested on an Et_q8_v1_6,
Ippo_q8h_v1_2_a33_1024x600, Ippo_q8h_v1_2 and TZX-Q8-713B7 tablet, and the
forfun_q88db_defconfig is identical to q8_a13_tablet_defconfig.
This leaves only the Ippo_q8h_v5 untested with the new generic defconfigs
but there is no reason to assume that it will not work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
Select CONFIG_SPL_STACK_R for sunxi boards, this gives us much more
room on the stack once we've the DRAM running.
Besides being a good change to have on itself, this also paves the
way for switching to using malloc_simple in the SPL which cuts of
close to 4KiB of the SPL size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Seen this one in the wild. Is labelled "Raspberry Pi Model A+ V1.1,
(C) Raspberry Pi 2014". A standard A+ board, much like the one with
version 0x12, didn't notice any differencies.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
On keystone2 Lamarr and Edison platforms, the PA clocksource
mux in PLL REG1, can be changed only after enabling its clock
domain.
So selecting the output of PASS PLL as input to PA only after
enabling the clockdomain.
This is as per the debug done by "Vitaly Andrianov <vitalya@ti.com>"
and based on the previous work done by "Hao Zhang <hzhang@ti.com>"
Fixes: d634a0775bcf ("ARM: keystone2: Cleanup PLL init code")
Reported-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
We need "u-boot,dm-pre-reloc" in the socfpga_cyclone5_socdk.dts file in
order for the SPL to use SD/MMC.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Update the L2 AUX CTRL settings for the SoCFPGA.
Enabling D and I prefetch bits helps improve SDRAM performance on the
platform.
Also, we need to enable bit 22 of the L2. By not having bit 22 set in the
PL310 Auxiliary Control register (shared attribute override enable) has the
side effect of transforming Normal Shared Non-cacheable reads into Cacheable
no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add 'volatile' qualifier to the asm statement in get_cr()
so that the statement is not optimized out by the compiler.
(http://comments.gmane.org/gmane.linux.linaro.toolchain/5163)
Without the 'volatile', get_cr() returns a wrong value which
prevents enabling the MMU and later causes a PCIE VA access
failure.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
PCI driver currently hangs on mx6qp.
Toggle the reset bit with the appropriate timings to fix the issue.
Based on the FSL kernel driver implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Initialize all GICD_IGROUPRn registers and set up GICC_CTLR to enable
interrupts to the primary CPU. This fixes issues seen after booting a
Linux kernel from U-Boot.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For EL3 and EL2, the documentation says that bits 31 and 23 are reserved
but should be written as 1.
For EL1, only bit 23 is not reserved, so only write bit 31 as 1.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the inner shareable attribute for memory, which makes more sense
considering that this code is called when caches are being enabled.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit 623d96e89aca6("imx: wdog: correct wcr register settings")
issuing a 'reset' command causes the system to hang.
Unlike i.MX and Vybrid, the watchdog controller on LS102x is big-endian.
This means that the watchdog on LS1021 has been working by accident as
it does not use the big-endian accessors in drivers/watchdog/imx_watchdog.c.
Commit 623d96e89aca6("imx: wdog: correct wcr register settings") only
revelead the endianness problem on LS102x.
In order to fix the reset hang, introduce a reset_cpu() implementation that
is specific for ls102x, which accesses the watchdog WCR register in big-endian
format. All that is required to reset LS102x is to clear the SRS bit.
This approach is a temporary workaround to avoid a regression for LS102x
in the 2015.10 release. The proper fix is to make the watchdog driver
endian-aware, so that it can work for i.MX, Vybrid and LS102x.
Reported-by: Sinan Akman <sinan@writeme.com>
Tested-by: Sinan Akman <sinan@writeme.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Execution branches on feedback mode are swapped, this has no effect
if default direct mode is on (then p_div is equal to 1 and Fout equals
to Fcco), that's why the problem remained unnoticed for a long time.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
According to ARM PrimeCell PL175 documentation WAIT_OEN config value
is defined without any additional clocks added to the value set by a
client, the change fixes the wrong interface to WAIT_OEN config.
The change also touches a single user of LPC32xx EMC and corrects
configured "output enable delay" value on its side according to the
changed interface.
No functional change intended.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
We run 4 Arndale boards in our automated test framework, they have
been running quite happily for quite some time using a Debian Wheezy
userspace.
However when upgrading to a Debian Jessie we started seeing frequent
segmentation faults from gcc when building the kernel, to the extent
that it is unable to successfully build the kernel twice in a row, and
often fails on the first attempt.
Searching around I found https://bugs.launchpad.net/arndale/+bug/1081417
which pointed towards http://www.spinics.net/lists/kvm-arm/msg03723.html
and CPU Errata 773022 and 774769.
This errata needs to be applied to all processors in an SMP system,
meaning that the usual strategy of applying them in
arch/arm/cpu/armv7/start.S is not appropriate (since that applies to
the boot processor only). Instead we apply these errata in the secure
monitor which is code that is traversed by all processors as they are
brought up.
The net affect on Arndale is that ACTLR changes from 0x40 to
0x2000042. I ran 17 kernel compile iterations overnight with no
segfaults.
Runtime testing was done on our v2014.10 based branch and forward
ported (with only minimal and trivial contextual conflicts) to current
master, where it has been build tested only.
I suppose in theory these errata apply to any Exynos5250 based boards,
but Arndale is the only one I have access to and I have therefore
chosen to be conservative and only apply it there.
Also, reorder CONFIG_ARM_ERRATA_794072 in README to make the list
numerically sorted.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Create an additional FVP configuration to boot images pre-loaded into
DRAM.
Sometimes it's preferential to boot the model by loading the files
directly into DRAM via model parameters, rather than using
SemiHosting.
An example of model parmaters that are used to pre-load the files
into DRAM:
--data cluster0.cpu0=Image@0x80080000 \
--data cluster0.cpu0=fvp-base-gicv2-psci.dtb@0x83000000 \
--data cluster0.cpu0=uInitrd@0x84000000
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[trini: Update board/armltd/vexpress64/Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Erratum A-008022 has been fixed on LS1021A Rev2.0.
So we can use DSPI2 now, this patch enable DSPI2
in dts for LS1021ATWR.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When malloc_base initially gets setup in the SPL it is based on the
current (early) stack pointer, which for rockchip is pointing into SRAM.
This means simple memory allocations happen in SRAM space, which is
somewhat unfortunate. Specifically a bounce buffer for the mmc allocated
in SRAM space seems to cause the mmc engine to stall/fail causing
timeouts and a failure to load the main u-boot image.
To resolve this, reconfigure the malloc_base to start at the relocated
stack pointer after DRAM has been setup.
For reference, things did work fine on rockchip before 596380db was
merged to fix memalign_simple due to a combination of rockchip SDRAM
starting at address 0 and the dw_mmc driver not checking errors from
bounce_buffer_start. As a result, when a bounce buffer needed to be
allocated mem_align simple would fail and return NULL. The mmc driver
ignored the error and happily continued with the bounce buffer address
being set to 0, which just happened to work fine..
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This device uses SDHCI driver, for eMMC and SD cards.
Trying bind the DW MMC driver with fdt node without all
required properties, causes printing an error.
This commit disables the DW MMC node.
Tested-on: Trats
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Łukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
After rework of code by:
commit: d952796 Exynos5: Use clock_get_periph_rate generic API
function get_mmc_clk() always returns -1 for Exynos 4.
This was caused by omitting, that SDHCI driver for Exynos 4,
calls get_mmc_clk(), with mmc device number as argument,
instead of pinmux peripheral id, like DW MMC driver for Exynos 5.
By this commit, the code directly calls a proper function
to get mmc clock for Exynos 4, without checking the peripheral id.
Tested on: Odroid U3/X2, Trats, Trats2, Odroid XU3, Snow (by Simon).
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
We should follow 'read->set/clr bit->write' flow for enable_fec_anatop_clock,
otherwise we may overridden configuration before enable_fec_anatop_clock.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Cc: Fabio Estevam <fabio.estevam@freescale.com>
As reported by Simon Guinot, commit ade741b3
"arm: mvebu: Call timer_init early before PHY and DDR init" breaks
Kirkwood platforms. As the static variable "init_done" is not
available at that early boot time. This patch moves it to explicitly
to the data section, making it available at that time.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Currently booting on A38x is broken. As the current code tries to detect
the SoC family to disable the MMU for the A38x at runtime. But before the
internal registers are switched to the new location (0xf100.0000), this
runtime detection does not work. As all macros / defines are already
assigned to the new location at 0xf100.0000. But the registers are sill
mapped to the default location at 0xd000.0000.
This patch now makes sure, no such runtime detection is used before
the internal registers are configured to the new location. After this,
the remaining cache cleanup is executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts[i] files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.
misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().
The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch follows up on a discussion of ways to improve support
for the sunxi FEL ("USB boot") mechanism, especially with regard
to boot scripts, see:
https://groups.google.com/d/msg/linux-sunxi/wBEGUoLNRro/rHGq6nSYCQAJ
The idea is to convert the (currently unused) "pad" bytes in the
SPL header into an area where data can be passed to U-Boot. To
do this safely, we have to make sure that we're actually using
our "sunxi" flavor of the SPL, and not the Allwinner boot0.
The modified mksunxiboot introduces a special signature to the
SPL header in place of the "pub_head_size" field. This can be
used to reliably distinguish between compatible versions of sunxi
SPL and anything else (older variants or Allwinner's boot0).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sunxi platform currently doesn't seem to make any use of the
asm/arch-sunxi/spl.h file. This patch moves some declarations from
tools/mksunxiboot.c into it.
This enables us to reuse those definitions when extending the
sunxi board code (boards/sunxi/boards.c).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
crt0.S will both memset the bss sectioan and call board_init_r for us,
so there is no need to do either ourselves.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Use DM for the pl01x serial driver on hikey. Also allow UART0 or
UART3 to be chosen via Kconfig.
By default we now output to UART3 as the latest version of ATF outputs
to this UART. Also UART3 comes out on the LS connector, as opposed to
UART0 which goes to a unpopulated header.
As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and
call the pinmux configuration code for the UART. Before we were
relying on ATF having already configured the pin configuration.
NB: Upstream Linux kernel doesn't yet support UART3, so serial console
will still be output on UART0 when booting a upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Most platforms enable these options from Kconfig rather
than the configs header file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, the USB boot mode is supported by an external loader and
U-boot proper image is put on the section 0. This commit allows
access there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The DDR SDRAM initialization code has not been mainlined yet, but
U-Boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Before this commit, the Kconfig menu in mach-uniphier only allowed us
to choose one SoC to be compiled. Each SoC has its own defconfig file
for the build-test coverage. Consequently, some defconfig files are
duplicated with only the difference in CONFIG_DEFAULT_DEVICE_TREE and
CONFIG_{SOC_NAME}=y.
Now, most of board-specific parameters have been moved to device trees,
so it makes sense to include init code of multiple SoCs into a single
image as long as the SoCs have similar architecture. In fact, some
SoCs of UniPhier family are very similar:
- PH1-LD4 and PH1-sLD8
- PH1-LD6b and ProXstream2 (will be added in the upcoming commit)
This commit will be helpful to merge some defconfig files for better
maintainability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move init code of low-level debug into a single file.
This is helpful to create an image that runs on multiple SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, IECTRL is enabled after pin-mux settings for the low-level
debugging for PH1-LD4 and PH1-sLD8. While IECTRL is disabled, input
signals are pulled-down, i.e. glitch signal (Low to High transition)
problem occurs if pin-mux is set up first. As a result, one invalid
character is input to the UART block and the auto-boot counting is
terminated immediately.
The correct initialization procedure is:
[1] Enable IECTRL (if IECTRL exists for the pins)
[2] Set up pin-muxing
[3] Deassert the reset of the hardware block
Currently, the low-level debugging is working for PH1-sLD3 and
PH1-Pro4, but just in case, follow the sequence for all the SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I want these prefixed with CONFIG_ARCH_UNIPHIER_ to clarify
they belong to UniPhier SoC family.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
It is no longer necessary to define CONFIG_SUPPORT_CARD_* globally.
Move them to a C file as local macros. Also, rename the C file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The macro, led_write(), is now only used in C sources. There is no
more reason to keep the tricky assembly macro. Replace it with a
new C function led_puts().
Also, rename board.h to micro-support-card.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The wrapper functions, uniphier_board_*, are just making function
calls complex. Remove them.
Also, use empty inline functions in case CONFIG_MICRO_SUPPORT_CARD
is disabled, so that prototype checking works.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Device tree specifies the available memory ranges in its "/memory"
node. Use it to simplify the CONFIG defines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To achieve the complete run-time configuration by device trees, ifdef
conditionals in header files are not preferable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In UniPhier SoCs before ProXstream2 and PH1-LD6b, two address spaces
0x00000000 - 0x0fffffff
0x40000000 - 0x4fffffff
are both mapped to the external bus (also called system bus),
so either was OK.
In the newest two SoCs, the former (0x00000000 - 0x0fffffff) is
assigned for the serial NOR interface.
Going forward, use the latter for the external bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Historically (for compatibility with very old platforms), two
different types of micro support cards have been used with the
UniPhier SoC development boards. It has been painful to maintain
both. Having one of them is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These input enable settings are handled by the pinctrl drivers.
Because the external bus pins are input-enabled by default, on-board
devices such as LED still work fine even with this delayed input
enabling.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As the UniPhier serial driver had already switched to Drive Model
and the pinctrl drivers are now enabled, these pin-muxing settings
are properly handled by the pinctrl drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "u-boot,dm-pre-reloc" for device nodes we want in SPL DTB
(spl/u-boot-spl.dtb).
The "soc" node (this is simple-bus node) also needs the property
to bind the pinctrl node located under it.
I am collecting this U-Boot specific hack to the bottom of board
DTS rather than inserting "u-boot,dm-pre-reloc" into SoC DTSI.
My goal is to sync DTSI with Linux for easier maintenance.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
boot_mode_apply should be applied only with CONFIG_CMD_BMODE enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Some i.MXes use __NA_ or 0 to avoid setting mux_mode, but the following patch
only take i.MX6/7 into consideration.
"c3c8a5748897b24f18618047804317167a531dd3 imx-common: fix iomux settings"
Use is_soc_type(MXC_CPU_MX7) to avoid breaking other i.MXes when
setting mux_mode.
In this patch, switch to use "asm/imx-common/sys_proto.h" to avoid
build break for "is_soc_type" for vf610 and mx25.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Rename the socfpga_cyclone5.h to socfpga_cyclone5_socdk.h, and
socfpga_arria.h to socfpga_arria5_socdk.h. This matches the other SoCFPGA
board config files.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
drop select CPU_V7 for board target, since ARCH_MX7 selects CPU_V7.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
When setting iomux for a pin mux, there is no need to check mux_ctrl_ofs.
Also If still checking mux_ctrl_ofs, we have no chance to set iomux
for i.MX7D IOMUXC_LPSR_SW_MUX_CTL_PAD_GPIO1_IO00, because the mux_ctrl_ofs
for this register is 0.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence"). The Tegra114 TRM doesn't contain this information, but
the programming of PLLC is the same on Tegra114 and Tegra124.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enabling a PLL while IDDQ is high. The Linux kernel checks for this
condition and warns about it verbosely, so while this seems to work
fine, fix it up according to the programming guidelines provided in
the Tegra K1 TRM (v02p), Section 5.3.8.1 ("PLLC and PLLC4 Startup
Sequence").
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the SPI controllers found on Tegra20 SOCs.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
While clk_m and the oscillator run at the same frequencies on Tegra114
and Tegra124, clk_m is the proper source for the architected timer. On
more recent Tegra generations, Tegra210 and later, both the oscillator
and clk_m can run at different frequencies. clk_m will be divided down
from the oscillator.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On currently supported SoCs, clk_m always runs at the same frequency as
the oscillator input. However newer SoC generations such as Tegra210 no
longer have that restriction. Prepare for that by separating clk_m from
the oscillator clock and allow SoC code to override the clk_m rate.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some platforms have the means to determine the counter frequency at
runtime, so give them an opportunity to do so.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
AFAIK, for all PLLs on all Tegra SoCs, the primary PLL output frequency
is (input * m) / (n * p). However, PLLP's primary output (pllP_out0) on
T210 is the VCO output, and divp is not applied. pllP_out2 does have divp
applied. All other pllP_outN are divided down from pllP_out0. We only
support pllP_out0 in U-Boot at the time of writing.
Fix clock_get_rate() to handle this special case.
This corrects the returned rate for PLLP to be 408MHz rather than 204MHz.
In turn, this causes high enough dividers to be calculated for the various
peripheral clocks that feed off of PLLP. Without this, some peripherals
failed to operate correctly. For instance, one of my SD cards worked
perfectly but an older (presumably slower) card could not be read.
Note that prior to commit 722e000ccd "Tegra: PLL: use per-SoC pllinfo
table instead of PLL_DIVM/N/P, etc.", the calculated PLL frequency was
816MHz since the wrong values were being extracted from the PLLP divider
register. This caused overly large peripheral dividers to be calculated,
which while wrong, didn't cause any correctness issues; things simply ran
slower than they could.
Reported-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function is deleted by commit 2fccd2d96b
"tegra: Convert tegra GPIO driver to use driver model".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
P2371-2180 is a P2180 CPU board married to a P2597 I/O board. The
combination contains SoC, DRAM, eMMC, SD card slot, HDMI, USB
micro-B port, Ethernet via USB3, USB3 host port, SATA, PCIe, and
two GPIO expansion headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 0abdd9d0 "arm: Remove nhk8815 boards and nomadik arch" missed one
reference to this arch. Lets remove this as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>