Commit graph

153 commits

Author SHA1 Message Date
Albert ARIBAUD
1c27059a2f Merge remote-tracking branch 'u-boot/master' 2012-09-30 23:49:17 +02:00
Wu, Josh
1c5794a13e at91sam9x5: set default EBI I/O drive configuration.
This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register).

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-13 14:27:28 +02:00
Andreas Bießmann
a420dfe2b0 avr32: add atngw100mkii board
This patch is derived from an older patch provided by atmel in its
buildroot-avr32-v3.0.0.tar.bz2

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
2012-09-13 13:33:11 +02:00
Wu, Josh
2ab4c74604 at91: 9x5: change SMC config timing that both works for PMECC & non-PMECC.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: voice.shen@atmel.com
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 17:06:14 +02:00
Andreas Bießmann
bfc325ed38 arm:at91-boards: remove console_init_f where unnecessary
A lot of at91 boards have the console_init_f in board_init. This is useless
cause it was called before by generic code in lib/board.c.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Jens Scharsig <esw@bus-elektronik.de>
cc: Stelian Pop <stelian@popies.net>
cc: Sedji Gaouaou<sedji.gaouaou@atmel.com>
cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
cc: Eric Benard <eric@eukrea.com>
Tested-by: voice.shen@atmel.com
Tested-by: voice.shen@atmel.com
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-09-01 17:06:14 +02:00
Andreas Bießmann
82c4c64526 at91sam9263ek: remove unnecessary console_init_f
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Stelian Pop <stelian@popies.net>
2012-09-01 17:06:14 +02:00
Bo Shen
4ed9c88603 arm : at91sam9x5 : fix a small bug for NAND
fix a bug:
  when not boot from NAND, the NAND flash can not be detected.
  Using this to fix it

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 17:06:13 +02:00
Bo Shen
f7fa2f3740 arm : Atmel : add at91sam9x5ek board support
Add at91sam9x5ek board support, this board support the following SoCs
  AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 14:58:14 +02:00
Alexandre Belloni
e139cb31d3 AT91SAM9*: Change kernel address in dataflash to match u-boot's size
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap  0x00000000
ubootenv   0x00004200
uboot      0x00008400
kernel     0x00042000
fs         0x00252000

u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.

Now, the layout is:
bootstrap  0x00000000
ubootenv   0x00004200
uboot      0x00008400
kernel     0x00084000
fs         0x00294000

Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:30 +02:00
esw@bus-elektronik.de
2feb736661 Fix: broken boot message at serial line on AT91SAM9263-EK board
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:29 +02:00
Stelian Pop
c9e798d35a Fix Stelian's email address
Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-29 15:43:38 +01:00
Mike Frysinger
464c79207c punt unused clean/distclean targets
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used.  Punt them all.

MAKEALL didn't report any errors related to this that I could see.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-15 22:20:36 +02:00
Jason Kridner
2d3be7c456 led: remove camel casing of led identifiers globally
Result of running the following command to address Wolfgang's
comment about camel case:

for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done

Discussion:
http://patchwork.ozlabs.org/patch/84988/

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:30:52 +02:00
Wolfgang Denk
1c85752258 ARM: remove broken "at91rm9200dk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:15 +02:00
Wolfgang Denk
b550834458 ARM: remove broken "at91cap9adk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stelian Pop <stelian.pop@leadtechdesign.com>
2011-09-04 11:36:14 +02:00
Thomas Petazzoni
5cfeec5125 atmel: Update support of board AT91SAM9M10G45-EK to new style
Based on earlier work by Alex Waterman <awaterman@dawning.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2011-09-03 22:40:45 +02:00
Xu, Hong
cd46b0f2b9 AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Xu, Hong
f7aea46d6a AT91: Board fix for AT91SAM9261-EK
Fix board part of AT91SAM9261-EK according to the new scheme

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Xu, Hong
21d671d0c4 AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Albert ARIBAUD
a55d23ccf6 Remove volatile qualifier in get_ram_size() calls
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-17 17:11:53 +02:00
Graeme Russ
a60d1e5b8e Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-07-16 11:55:00 +02:00
Andreas Bießmann
221786525f atstk100x: switch to common cfi driver
This patch removes the board implemenatation for flash driver which can now
safely switched to the common cfi driver.

Compile tested for all atstk100x boards, runtime tested on atstk1002.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-07-04 10:55:27 +02:00
Andreas Bießmann
3432a93bcd at91rm9200ek: use atmel_usart
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-07-04 10:55:27 +02:00
Reinhard Meyer
8c6407fce3 AT91 rework: fix at91sam(9260/9g20/9xe)ek board port to build again:
Make ATMEL's at91sam9260/9g20/9xe-ek boards build again

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-06-21 22:26:22 +02:00
Jens Scharsig
8073399444 update arm/at91rm9200 work with rework rework110202
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
 * Fix: timer.c compile error io.h not found with arm/at91rm9200
 * update arm920t/at91 to ATMEL_xxx name scheme
 * update arm920t/at91 soc lib
 * update at91_emac driver

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
2011-06-21 22:26:21 +02:00
Andreas Bießmann
47293c18ba atstk100x: move CONFIG_SYS_TEXT_BASE to header
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:54 +02:00
Andreas Bießmann
da48437230 atngw100: move CONFIG_SYS_TEXT_BASE to header
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:54 +02:00
Andreas Bießmann
bb7dc6af20 avr32: use single linker script
This patch move the atstk100x linker script to $(CPUDIR) and delete other
pure copies of this file in each board directory.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:53 +02:00
Andreas Bießmann
758472cc7b avr32/config.mk: simplify PLATFORM_RELFLAGS
This patch removes PLATFORM_RELFLAGS from board specific config.mk files and
define them in arch specific config.mk file.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:53 +02:00
Andreas Bießmann
c8e7ddd4c6 avr32: fix linking
This patch fixes following error:

---8<---
avr32-linux-ld: --gc-sections and -r may not be used together
--->8---

Since 8aba9dceeb all avr32 boards are broken due
to linking error as seen above.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:52 +02:00
Andreas Bießmann
f4278b716c avr32: fixup definitions to ATMEL_BASE_xxx
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:50 +02:00
Scott Wood
83b7e2a7f2 Handle most LDSCRIPT setting centrally
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk.  Some
are found using an arch-specific rule for looking in CPUDIR, etc.

Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.

Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.

If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.

If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:

$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds

Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules.  These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-30 00:59:47 +02:00
Po-Yu Chuang
44c6e6591c rename _end to __bss_end__
Currently, _end is used for end of BSS section.  We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-03-27 19:18:37 +02:00
Andreas Bießmann
3a4ff8b3cd at91rm9200ek: add configure target for RAM boot
This patch also removes now unnecessary config.mk in board directory and
make usage of new features in boards.cfg.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-07 22:08:06 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Andreas Bießmann
99fa97e955 at91rm9200ek: convert to at91
This patch removes some functionality from at91rm9200ek board but the
remaining functionality does now work with newer at91 code and
arm-relocation.

Currently missing features are:
 - dataflash booting (due to missing HW for testing)
 - MMC/SD-Card
 - first stage bootloader support is completely removed (not needed for
   NOR)

Cause this board was (some days ago) reference for all at91rm9200 based
boards this should be a good starting point to convert all remaining
at91rm9200 borads to at91 code. Aside from that this is a good base to
get some drivers between at91sam/at91rm/avr32 merged.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-19 15:11:46 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Haavard Skinnemoen
1f36f73fe7 avr32: Add simple paging support
Use the MMU hardware to set up 1:1 mappings between physical and virtual
addresses. This allows us to bypass the cache when accessing the flash
without having to do any physical-to-virtual address mapping in the CFI
driver.

The virtual memory mappings are defined at compile time through a sorted
array of virtual memory range objects. When a TLB miss exception
happens, the exception handler does a binary search through the array
until it finds a matching entry and loads it into the TLB. The u-boot
image itself is covered by a fixed TLB entry which is never replaced.

This makes the 'saveenv' command work again on ATNGW100 and other boards
using the CFI driver, hopefully without breaking any rules.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2010-09-03 15:13:02 +02:00
Haavard Skinnemoen
9cec2fc209 avr32: Use uncached() macro to get an address for SDRAM init
The paging system which is required to set up caching properties has not
yet been initialized when the SDRAM is initialized. So when the
map_physmem() function is converted to return the physical address
unchanged, the SDRAM initialization will break on some boards.

The avr32-specific uncached() macro will return an address which will
always cause uncached accessed to be made. Since this happens in the
board code, using avr32-specific features should be ok, and will allow
the SDRAM initialization to keep working.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2010-09-03 15:12:52 +02:00
Ben Warren
6bb4679017 Write MAC address automatically on MACB-based boards
Also, remove all calls to eth_init() in boards that use MACB

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 00:14:29 -07:00
Sergey Matyukevich
64203c7b0f USB OHCI support for at91sam9g45 SoC
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.

Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
2010-06-30 21:37:36 +02:00
Andreas Bießmann
418cbb0abc avr32: fix linking of atstk100x and favr32 boards
When building some avr32 boards out of tree (e.g. O=..) the linker script could
not be found. This patch references the linker script in source tree.

Signed-off-by: Andreas Biemann <biessmann@corscience.de>
2010-06-29 22:37:11 +02:00
Achim Ehrlich
7c966a8bdf ARM change name of defines for AT91 arm926ejs
Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:

AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK

Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
2010-03-07 12:36:35 -06:00
Jens Scharsig
1b34f00c28 update at91sam9263ek board to new SoC access
* convert at91sam9263ek board to use c stucture SoC access
 * change gpio access to at91_gpio syntax

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:55 -06:00
Jens Scharsig
c041e9d212 new at91_emac network driver (NET_MULTI api)
* add's at91_emac (AT91RM9200) network driver (NET_MULTI api)
* enable driver with CONFIG_DRIVER_AT91EMAC
* generic PHY initialization
* modify AT91RM9200 boards to use NET_MULTI driver
* the drivers has been tested with LXT971 Phy and DM9161 Phy at
  MII and RMII interface

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Wolfgang Denk
e8fac25e83 at91sam9261ek.c: fix minor coding style issue.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 21:50:19 +01:00
Albin Tonnerre
50b5fff558 at91sam9260/afeb9260: Fix SPI initialization
Commit 7ebafb7ec1 introduced a mistake in the spi
init function call for those boards. This patch fixes this.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2009-09-01 22:10:10 +02:00
Sedji Gaouaou
5ccc2d99d6 at91: Introduction of at91sam9g10 SOC.
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:56:11 +02:00
Sedji Gaouaou
22ee647380 at91: Introduction of at91sam9g45 SOC.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:43:34 +02:00
Sedji Gaouaou
0aafde1dc7 at91sam9260/9263: add back up for the rst(reset controller).
On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Stelian Pop <stelian@popies.net>
2009-07-06 21:50:09 +02:00