uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds.
To disabled watchdog during kernel boot, WDI pin of that chip needs to be
in "high impedance" state. I.mx6 gpio configuration does not contemplate
tristate, so pin is set as input in high impedance.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031).
Ethernet speed is currently limited to 10/100Mbps.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Previous uDoo configuration adopts register settings for DDR3, clock, muxing,
etc. taken from Nitrogen6x. uDoo schematics is rather different from that board,
and it needs customized setting for most of the registers.
All this changes can be considered atomical since it is part of initial support
of the board.
Patch changes uDoo configuration files path to a specific one, and adopt
optimized value for every configured register.
Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabre board has a m25p32 SPI NOR connected to ECSPI1 port.
Add support for it.
This patch allows the SPI NOR flash to be succesfully detected:
=> sf probe
SF: Detected M25P32 with page size 256 Bytes, erase size 64 KiB, total 4 MiB
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently HDMI splash screen is selected by default on mx6sabresd boards.
As LVDS is also enabled, this causes incorrect colors to be displayed im the
LVDS panel.
Fix this by selecting the LVDS panel as the default splash output and only keep
HDMI or LVDS turned on at the same time.
Acked-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to pass p->bus differently when the PMIC is connected via SPI
or via I2C.
Handle the both cases in the same way.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On efikamx board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx31pdk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
On mx51evk board the PMIC is connected via SPI interface, so it does not make
sense to pass I2C_PMIC into the pmic_init() interface.
Pass the SPI bus number via CONFIG_FSL_PMIC_BUS option instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
OCOTP driver is currently selected via CONFIG_MXC_OCOTP option.
Remove the old OCOTP related options, as they are not used anymore.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the titanium board is not a Freescale board, move its
BSP code from the freescale board directory to the newly created
barco board directory.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Setting the direction and an output value should be done by
1) set the desired output value,
2) switch to output.
If this is done in the inverse order, there can be a glitch on
the GPIO line.
This patch fixes this by using the order as described above.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefano Babic <sbabic@denx.de>
There is no real benefit in adding the board name into U-boot's prompt, so
remove the custom CONFIG_SYS_PROMPT definitions so that the standard "=> "
prompt is used across FSL boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
- add splashpos=m,m to default environment, so splash screen is always
centered.
- adapt environment for bootcount feature
- add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
store the bootcount in the environment, as we have no softreset
save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
Add for the siemens boards the possibility to define in dfu mode,
the iSerialNumber and the bcdDevice fields in the USB Device
descriptor.
- fix upgrade mechanism based on bootcount
Correct location of saveenv and remove not active variable.
Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
reboot board in case of empty kernel partition. Without
these defines an empty kernel partition leads to an
abort of boot process and one remains in u-boot prompt.
- general cleanup of dxr2, pxm2 and rut boards
all:
* Remove net boot from bootcmd
Ping can cause a crash on boards without ethernet phy.
net_nfs command is used only for development
* Add reset at the end of bootcmd
In order to have an immediate reset of the boot when bootcmd
fails, add reset at the end of bootcmd.
rut:
* add nand_img_size
dxr2:
* update nand_img_size
* ddr3 timings updated with iocontrol property that can be
modified via eeprom. New default parameters from software
leveling with draco ES2.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Pascal Bach <pascal.bach@siemens.com>
Signed-off-by: Roger Meier <r.meier@siemens.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Michel <matthias.michel@siemens.com>
Cc: Tom Rini <trini@ti.com>
add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility. So add
another symbol for the bootcount driver for the IP block.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Switch to using the generic gpio_led driver instead of the private to
cm_t35 board led implementation.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Commit f6d1f6e4a5 broke selection of UARTs
other than UART0 for am335x_evm configurations by setting CONS_INDEX to
1 for all configurations. Revert the CONS_INDEX changes.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Update my email address as ti814x_evm maintainer to save
people some frustrating bounces and non-response.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"
enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is introduced. If "upgrade_available" is
0, "bootcount" is always 0 therefore no need to save the
environment on u-boot boot, if "upgrade_available" is 1 "bootcount"
is incremented in the environment and environment gets written
on u-boot start.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0 (for example with fw_setenv),
if a boot was successfully.
Signed-off-by: Heiko Schocher <hs@denx.de>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
A weak annotation is needed in order to prevent link errors when
get_ticks is overridden. This fixes sandbox build.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX
Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The env export command doesn't export the first variable of the list
since commit 5a31ea04c9
"env grep" - reimplement command using hexport_r()
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
As originally implemented, setting the AUTOBOOT_KEYED config option will
prevent users from breaking into the autoboot script with ctrl-c. Restore
that option with a new config symbol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Staticize local functions in xuartlite driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Curently memcpy copies string without null terminating char because
function strlen returns only number of characters excluding
null terminating character. Replace memcpy with strcpy.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Tom Rini <trini@ti.com>
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Giuseppe Pagano
Fabio Estevam
Eric Nelson
Marek Vasut
Stefan Roese
Michael Heimpold
Samuel Egli
Heiko Schocher
Tom Rini
Igor Grinberg
Andrew Bradford
Matt Porter
Albert ARIBAUD
Rob Herring
Suriyan Ramasami
Axel Lin
Pierre Aubert
Mark Langsdorf
Piotr Wilczek
Luka Perkov
Tim Harvey
Masahiro Yamada
Egbert Eich