Some UniPhier boards are equipped with an expansion slot that
some optional SRAM/NOR-flash cards can be attached to. So, run-time
detection of the number of flash banks would be more user-friendly.
Until this commit, UniPhier boards have achieved this by (ab)using
board_flash_wp_on() because the boot failed if flash_size got zero.
Fortunately, this problem was solved by commit 70879a9256 (flash:
do not fail even if flash_size is zero).
Now it is possible to throw away such a tricky workaround. This
commit also enables CONFIG_SYS_MAX_FLASH_BANKS_DETECT for further
refactoring.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
__user and __iomem are defined in include/linux/compiler.h.
MAX_ERRNO is defined in include/linux/err.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The CPU directory of IMX6 is arch/arm/cpu/armv7, so setting
CONFIG_SPL_START_S_PATH to arch/arm/cpu/armv7 is totally redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
The CPU directory of this board is arch/powerpc/cpu/mpc5xxx.
Without the CONFIG_SPL_START_S_PATH and CONFIG_SPL_LDSCRIPT defines,
the same start.o and u-boot-spl.lds are selected by default.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
The CPU directory of this board is arch/powerpc/cpu/ppc4xx.
Without the CONFIG_SPL_START_S_PATH and CONFIG_SPL_LDSCRIPT defines,
the same start.o and u-boot-spl.lds are selected by default.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.
It has not been converted to generic board yet and mpc8xx is old
enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Enable ENV_IS_IN_FAT so that the environment can be stored persistently.
It's stored in the FAT partition that the RPi firmware requires. On most
RPis, this is on the SD card (which must be present in order for the
system to boot). On the CM this is on the built-in eMMC device.
Since we now have a persistent environment, there's no need to load
uEnv.txt at boot; we only did that to work around the lack of persistent
environment.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The U-Boot port runs on a variety of RPi models, not just the B. So,
rename the port to something slightly more generic.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Some configurations have been moved to Kconfig and the difference
among the config headers of UniPhier SoC variants is getting smaller
and smaller. Now is a good time to merge them into a single file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
There are two kinds of expansion boards which are often used for
the UniPhier platform and they are only exclusively selectable.
It can be better described by the "choice" menu of Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Remove the now unnecessary clocking info from the SoCFPGA
config header. As this info in now used directly in the SPI driver
itself.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Enable support for the DW master SPI controller in the config header
for the SoCFPGA. This controller can only be enabled, if DT support
is enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
With this driver enabled for SoCFPGA, access to SPI NOR flash is
supported.
The configuration (page size, timing info) will be taken from the
DT. See socrates as an example.
This QSPI supports depends on DT. So QSPI is only enabled if
CONFIG_OF_CONTROL is defined (see socfpga_socrates_defconfig).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The SD supply Voltage was 3.3V on T4240RDB, so enabled 3.3V support for eSDHC.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Wujie Qiu <B49553@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Convert T1040QDS and T1040RDB to use generic board code.
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add configs:
o CONFIG_SYS_GENERIC_BOARD
o CONFIG_DISPLAY_BOARDINFO
in C29XPCIE config header file to use U-boot generic
board code.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add configs:
o CONFIG_SYS_GENERIC_BOARD
o CONFIG_DISPLAY_BOARDINFO
in P1023RDB config header file to use U-boot generic
board code.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
cppcheck reports:
[board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize
remove the CONFIG_SYS_RAMBOOT define to prevent this error report.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
Use generic board architecture for p1010rdb, tested with NOR
boot on p1010rdb-pb.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The define CONFIG_FSL_SATA_V2 is missing, so SATA is not available
in U-boot.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use generic board architecture for p1025-twr, tested with NOR
boot and NAND boot on p1025-twr.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable interactive debugging by default. Remove DDR controller interleaving
because this SoC only has one controller. Use auto chip-select interleaving
to detect number of ranks.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.
Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
add FIT support and set "boardid" from factoryset records
"DEV/id" and "COMP/ver". "boardid" is used for selecting
which fit configuration gets booted on the board.
Signed-off-by: Heiko Schocher <hs@denx.de>
CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION ought to be called
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION to keep it consistent with other config
options such as: CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR.
In addition, it is not related to raw mode booting but to fs mode instead.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
* Since the emmc isn't always programed trying to load the fs from the
emmc causes boot failures/kernel panic.
* The current bootcmd is set to:
bootcmd=run findfdt; run mmcboot;setenv mmcdev 1; setenv bootpart 1:2; \
setenv mmcroot /dev/mmcblk0p2 rw; run mmcboot;
My guess is the env variables should be set so that sd card boot
(dt,kernel,fs) is the default and then fallback to emmc if it fails (no
sd card detected)
The current bootcmd attempts to set mmcroot to the sd card rootfs but
that code doesn't run due to mmcboot being ran early on.
Signed-off-by: Franklin Cooper Jr. <fcooper@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the characters of the error message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the characters of the error message:
"Unknown command '' - try 'help'".
Provide a default size for CONFIG_SYS_PBSIZE so that it can store the error
message and allows the error message to be printed correctly with no hang.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
With enabled console_mux for serial input and usb keyboard sometimes
characters get lost when typing too fast at the serial input (pasting
strings in serial console window). Fix this by using INT_QUEUE for
polling the usb keyboard.
Signed-off-by: Soeren Moch <smoch@web.de>
Add thermal support so that the temperature of the chip can be displayed on
boot:
U-Boot 2015.01-rc1-18268-g1366c05-dirty (Nov 25 2014 - 13:02:42)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 50 C
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
The fdt_path_offset() checks an alias too.
fdtdec_get_alias_node(blob, "foo") is equivalent to
fdt_path_offset(blob, "foo").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
As well as locating the ROM on the PCI bus, allow the ROM to be supplied to
the emulator. Split the init up a little so that callers can supply their
own interrupt routines. Also allow a vesa mode to be provided, to be
selected once the BIOS run is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some platforms don't have native code for dealing with their video
hardware. In some cases they use a binary blob to set it up and perform
required actions like setting the video mode. This approach is a hangover
from the old PC days where a ROM was provided and executed during startup.
Even now, these ROMs are supplied as a way to set up video. It avoids the
code for every video chip needing to be provided in the boot loader. But
it makes the video much less flexible - e.g. it is not possible to do
anything else while the video init is happening (including waiting hundreds
of milliseconds for display panels to start up).
In any case, to deal with this sad state of affairs, provide an API for
execution of x86 video ROMs, either natively or through emulation.
Signed-off-by: Simon Glass <sjg@chromium.org>
For option ROMs we can use these extensions to request a particular video
mode. Add a header file which defines the binary interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some PCI functions cannot be auto-configured. Add a function to set up a
fixed BAR which can be used in these situations. Also add a function to read
the current address of a BAR.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable this option so that we can configure the available PCI devices. Also
make sure that PCI is available early after relocation as we use it for
several other subsystems.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This new symbol may be defined by the compiler. If it is, avoid a compiler
warning when USE_STDINT is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
Add a generic helper to fill and enable simplefb nodes.
The first user of this will be the sunxi display code.
lcd_dt_simplefb_configure_node is also a good candidate to be converted
to use this, but that requires someone to run some tests first, as
lcd_dt_simplefb_configure_node does not honor #address-cells and #size-cells,
but simply assumes 1 and 1 for both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch enhances the boot of origen board by adding support to ext2, bootz, initrd, bootenv loading and boot script.
It still keeps the previous mmc load command if boot script fails.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add define CONFIG_SYS_WRITE_SWAPPED_DATA.
For LS1021AQDS and LS1021QTWR nor flash write should swap the
bytes when handle unaligned tail bytes.
Because of the ending, if the date bus width is 16-bits and the
number of bytes is odd, we should swap the byte when write the
last one.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Implement sata stop command.
This introduces the __sata_stop() weak function, which mirrors
the weak __sata_initialize() function, giving users the option of
undoing the custom steps performed in overrides of sata_initialize().
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal sandbox functions to use loff_t for file offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change the internal EXT4 functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update common/spl/spl_ext.c]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: Tom Rini <trini@ti.com>
Enable md5sum to obtain the MD5 of the read and written files to check
their contents for validity.
Use map_sysmem() to map buffer in a sandbox environment.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since commit 0defddc851 (config: Add a default CONFIG_SYS_PROMPT),
each board header does not need to define CONFIG_SYS_PROMPT
as long as it uses the default prompt "=> ".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This macro can be overridden in source files (before including common.h)
and can be used to specify a prefix for debug and error messages. An
example of how to use this is shown below:
#define pr_fmt(fmt) "foo: " fmt
#include <common.h>
...
debug("bar");
The resulting message will read:
foo: bar
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
When enumerating devices, honour the pci_skip_dev() function. This can
be used by PCI controller drivers to restrict which devices will be
probed.
This is required by the NVIDIA Tegra PCIe controller driver, which will
fail with a data abort exception if an access is attempted to a device
number larger than 0 outside of bus 0. pci_skip_dev() is therefore
implemented to prevent any such accesses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Some filesystems have a UUID stored in its superblock. To
allow using root=UUID=... for the kernel command line we
need a way to read-out the filesystem UUID.
changes rfc -> v1:
- make the environment variable an option parameter. If not
given, the UUID is printed out. If given, it is stored in the env
variable.
- corrected typos
- return error codes
changes v1 -> v2:
- fix return code of do_fs_uuid(..)
- document do_fs_uuid(..)
- implement fs_uuid_unsuported(..) be more consistent with the
way other optional functionality works
changes v2 -> v3:
- change ext4fs_uuid(..) to make use of #if .. #else .. #endif
construct to get rid of unreachable code
Hit any key to stop autoboot: 0
=> fsuuid
fsuuid - Look up a filesystem UUID
Usage:
fsuuid <interface> <dev>:<part>
- print filesystem UUID
fsuuid <interface> <dev>:<part> <varname>
- set environment variable to filesystem UUID
=> fsuuid mmc 0:1
d9f9fc05-45ae-4a36-a616-fccce0e4f887
=> fsuuid mmc 0:2
eb3db83c-7b28-499f-95ce-9e0bb21cda81
=> fsuuid mmc 0:1 uuid1
=> fsuuid mmc 0:2 uuid2
=> printenv uuid1
uuid1=d9f9fc05-45ae-4a36-a616-fccce0e4f887
=> printenv uuid2
uuid2=eb3db83c-7b28-499f-95ce-9e0bb21cda81
=>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
In some cases we need to manually bind a device to a particular driver.
Add a function to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add dev_get_parent() as a convenience to obtain the parent of a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
When the device is created from a device tree node, it matches a compatible
string. Allow access to that string and the associated data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable i.MX thermal DM driver to mx6sabre_common.h file. Since the
thermal is used in init_sequence_f, so define the CONFIG_SYS_MALLOC_F_LEN
to support DM driver using in pre relocation phase.
Additional, thermal driver depends on ocotp, make sure to enable
CONFIG_MXC_OCOTP when CONFIG_IMX6_THERMAL is selected.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Add a new thermal uclass for thermal sensor and implement the imx
thermal driver basing on this uclass.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Since this function can use up quite a bit of space for its strings, disable
it by default in SPL. Use CONFIG_DM_WARN to re-enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Provide a CONFIG_DM_STDIO option to enable registering a serial device
with the stdio library. This is seldom useful in SPL, so disable it by
default when building for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
For SPL we don't expect to need to remove a device. Save some code space
by dropping this feature. The board config can define
CONFIG_DM_DEVICE_REMOVE if this is in fact needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The simple malloc() implementation is used when memory is tight. It provides
a simple buffer with an incrementing pointer.
At present the implementation is inside dlmalloc. Move it into its own file
so that it is easier to find.
Rather than using relocation as a signal that the full malloc() is
available, add a special GD_FLG_FULL_MALLOC_INIT flag. This signals that the
simple malloc() should no longer be used.
In some cases, such as SPL, even the code space used by the full malloc() is
wasteful. Add a CONFIG_SYS_MALLOC_SIMPLE option to provide only the simple
malloc. In this case the full malloc is not available at all. It saves about
1KB of code space and about 0.5KB of data on Thumb 2.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The faster functions are not actually available in SPL and the code size
likely isn't worth it. Use the normal memcpy() in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Implement SDRAM init using the Memory Reference Code (mrc.bin) provided in
the board directory and the SDRAM SPD information in the device tree. This
also needs the Intel Management Engine (me.bin) to work. Binary blobs
everywhere: so far we have MRC, ME and microcode.
SDRAM init works by setting up various parameters and calling the MRC. This
in turn does some sort of magic to work out how much memory there is and
the timing parameters to use. It also sets up the DRAM controllers. When
the MRC returns, we use the information it provides to map out the
available memory in U-Boot.
U-Boot normally moves itself to the top of RAM. On x86 the RAM is not
generally contiguous, and anyway some RAM may be above 4GB which doesn't
work in 32-bit mode. So we relocate to the top of the largest block of
RAM we can find below 4GB. Memory above 4GB is accessible with special
functions (see physmem).
It would be possible to build U-Boot in 64-bit mode but this wouldn't
necessarily provide any more memory, since the largest block is often below
4GB. Anyway U-Boot doesn't need huge amounts of memory - even a very large
ramdisk seldom exceeds 100-200MB. U-Boot has support for booting 64-bit
kernels directly so this does not pose a limitation in that area. Also there
are probably parts of U-Boot that will not work correctly in 64-bit mode.
The MRC is one.
There is some work remaining in this area. Since memory init is very slow
(over 500ms) it is possible to save the parameters in SPI flash to speed it
up next time. Suspend/resume support is not fully implemented, or at least
it is not efficient.
With this patch, link boots to a prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 machines U-Boot needs to be added to a large ROM image which is
then flashed onto the target board. The ROM has a particular format so it
makes sense for U-Boot to build this image automatically. Unfortunately
it relies on binary blobs so we cannot require this for the default
build as yet.
Create a u-boot.rom output file for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many of the x86 CONFIG options will be common across different boards. Move
them to a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For board IDs a common approach is to set aside several GPIOs for use in
determining the board ID. This can provide information about board features
and the revision.
Add a function that turns a list of GPIOs into an integer by assigning
each GPIO to a single bit.
Signed-off-by: Simon Glass <sjg@chromium.org>
In general we can't store things in the data section until we have inited
SDRAM. Some platforms allow this (e.g. those with SPL) but some don't. Move
the pointer to global_data so that it will work on all platforms.
Without this fix the serial port will not work prior to relocation with
driver model on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Permit decoding of a named memory region from the device tree. This allows
easy run-time configuration of the address of on-chip SRAM, SDRAM, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add an additional function for adding information to the device tree before
booting. This permits additions which are not board-specific.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
The message about needing to reset should be printed no matter what error
is printed. Also, an error should always be printed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Flash regions can optionally be compressed or hashed. Add the ability to
read this information from the flashmap.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Use the correct FDT data types for this function. Also add more debugging.
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This function is useful for ensuring that a node exists. Export it so it
can be used more widely.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
This commit replaces roundup macro with the one from Linux Kernel.
DEFINE_ALIGN_BUFFER must be fixed because typechecking can not
be used in this context.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
These macros seem to be useful for U-Boot too (or at least
harmless). Imported from Linux 3.18-rc2.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
U-Boot has imported various utility macros from Linux
scattering them to various places without consistency.
In include/common.h are min, max, min3, max3, ARRAY_SIZE, ALIGN,
container_of, DIV_ROUND_UP, etc.
In include/linux/compat.h are min_t, max_t, round_up, round_down,
etc.
We also have duplicated defines of min_t in some *.c files.
Moreover, we are suffering from too cluttered include/common.h.
This commit moves various macros that originate in
include/linux/kernel.h of Linux to their original position.
Note:
This commit simply moves the macros; the macros roundup,
min, max, min2, max3, ARRAY_SIZE are different
from those of Linux at this point.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
All the references of DIV_ROUND have been replaced with
DIV_ROUND_CLOSEST. Remove DIV_ROUND.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM1136 was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM1136 and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM1136.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM926EJS was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM926EJS and replaces
the only reference in arch/arm/lib/cache.c with CONFIG_CPU_ARM926EJS.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
CONFIG_CPU_ARM920T was introduced into Kconfig by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
This commit removes all the defines of CONFIG_ARM920T and replaces the
only reference in drivers/usb/host/ohci-hcd.c with CONFIG_CPU_ARM920T.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Some (not all) of ARMv7 boards define CONFIG_ARMV7, which is useless.
Besides, it is never referenced.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment device and
mmcdev variable are set to this device.
Signed-off-by: Ye.Li <B37916@freescale.com>
This is nowhere documented and only used
by two other boards. Replace it with
TQMA6_SPI_FLASH_SECTOR_SIZE.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since USDHC1 and USDHC3 added, the dev index for USDHC2 changed to
1. So modify the default mmcdev in environment variables to dev 1.
Signed-off-by: Ye.Li <B37916@freescale.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add complete USB EHCI support for MPC837XEMDS and MPC837XERDB
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This fixes CPLD timing from previous commit
ab06b236f7.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: This is the difference between v2 and v1 patch]
Reviewed-by: York Sun <yorksun@freescale.com>
a3m071 and a4m2k share one config header. So adding the generic board defines
in this one file is enough to convert both boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tune dlvision configuration similar to other gdsys boards to reduce memory
footprint.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The UBI layer will disable much of its error reporting when it is
compiled into the linux kernel to avoid stopping boot. We want this
error reporting in U-Boot since we don't initialize the UBI layer until
it is used and want the error reporting.
We force this by telling the UBI layer we are building as a module.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kmpark@infradead.org>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display (optional, disabled by default)
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable to boot only a raw u-boot.bin image from nand with the
CONFIG_SPL_NAND_RAW_ONLY define. This option saves space on
boards where spl space is low.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Allow to set the buck voltage for the max77686.
This will be used to reset the SMC LAN9730 ethernet on the odroids.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Compile-time tested only, as I currently don't have access to
the eval board.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
I was running into this limit with a not overly long PXE append line.
Since the PXE code wants to print the resulting command line increase
CONFIG_SYS_PBSIZE too.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This replaces the existing CONFIG_BOOTCOMMAND for exynos5250 and 5420.
exynos4 platforms seem to have existing complex extra env configuration for
booting and so are excluded here. Hence the bootcmd.h is added to
exynos5-common.h.
I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot
tested on arndale.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
...and remove explicit setting of things which this implies. This is done for
all exynos platforms (4 & 5) so it is added to exynos-common.h
I'm mainly interested in CONFIG_CMD_BOOTZ and CONFIG_SUPPORT_RAW_INITRD
I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot
tested on arndale.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since, not every board may have all memory channels configured
and all available banks of DMC used, we wish to refactor configs
for Memory Bank size and numbers as per board memory config.
For Example, Peach-Pit has 2GB memory and will be using only 4 banks
but Peach-Pi has 3.5GB memory and will be using all 7 available
SDRAM banks.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This adds following things :
- New config and defconfig for Peach-Pi board.
- Alterations in Kconfig and MAINTAINERS.
- Addition of CONFIG_EXYNOS5800.
- ADdition of exynos5800-peach-pi in dts list.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom Rini
Masahiro Yamada
Stephen Warren
Stefan Roese
Xiaobo Xie
Shengzhou Liu
Shaohui Xie
Shaveta Leekha
vijay rai
Chunhe Lan
Tang Yuantian
Heiko Schocher
Holger Brunck
Ying Zhang
Prabhakar Kushwaha
York Sun
Lubomir Popov
Nobuhiro Iwamatsu
Paul Kocialkowski
Felipe Balbi
Franklin S Cooper Jr
Fabio Estevam
Soeren Moch
Guillaume GARDET
Daniel Schwierzeck
Simon Glass
Hans de Goede
Luc Verhaegen
Alison Wang
Yuan Yao
Nikhil Badola
Nikita Kiryanov
Suriyan Ramasami
Thierry Reding
Christian Gmeiner
Ye.Li
Markus Niebel
Zhao Qiang
Dirk Eibach
Andrew Ruder
Bo Shen
David Müller (ELSOFT AG)
Ian Campbell
Akshay Saraswat