If no other bootoption works, try loading up device tree and zImage.
This is selected as the last option to allow backward compatibility as
well as support the recent trend in moving kernel boot to using zImage
and device tree.
NOTE: if uImage is present in bootpart, it will try this first and
will assume this is to be booted with bootm (so may be concatenated
image or plain vanilla ATAG MACHINE_ID based image)
Signed-off-by: Nishanth Menon <nm@ti.com>
For folks not using concatenated device tree with uImage, having
an handy function to find and load device tree is very handy.
So introduce findfdt and loadfdt and run findfdt by default to make
it easier on user scripts.
Signed-off-by: Nishanth Menon <nm@ti.com>
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we currently use. Sticking with existing conventions,
defaults will be:
ramdisk=ramdisk.gz
bootpart=0:2 (second partition)
bootdir=/boot (/boot in second partition)
This matches with the default behavior, these can be overriden by
env files as needed.
Signed-off-by: Nishanth Menon <nm@ti.com>
e682930867
(BeagleBoard: config: use uImage.beagle for tftp)
Introduced uImage.beagle which does not happen to be default output
file of Linux kernel build make uImage (output is uImage).
So, replace uImage.beagle with uImage
Signed-off-by: Nishanth Menon <nm@ti.com>
We do not use JFFS2 by default and it conflicts with
CONFIG_CMD_FS_GENERIC (ls command is the same). Since most of our
BOOTCMD can be simplified by using the FS_GENERIC, dropping JFFS2
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Joel Fernandes <joelf@ti.com>
We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion
of falcon mode to NAND. Previously it was half the size of the
eraseblock which is too small, increase to eraseblock size.
Signed-off-by: Tom Rini <trini@ti.com>
The previous location used for the "args" portion of falcon mode was too
small to allow for a device tree to be saved there, so move the location
slightly and increase the size. In addition, our previous kernel
location was part of the area we set aside for U-Boot itself, so move it
up a bit higher.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Now that we have falcon mode enabled, the partiton numbers for NAND have
changed, and we need to list entries for updating these parts of the
system. While adding falcon mode entires for eMMC (raw), we round up
the limit on U-Boot for ease of math later.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the
code duplication and only use the nitrogen6x source code to make board code
maintainance easier.
Tested booting a mainline device tree kernel on a mx6qsabrelite board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
CONFIG_SYS_FLASH_PROTECTION was active on most gdsys boards by default,
while hardware flash protection was not implemented.
Hardware support was added recently and we get into trouble because backward
compatibility is broken (u-boot can't unprotect the protected flash after a
downgrade). So we decided to disable hardware flash protection for all our boards.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
A set of accessor functions was added to be able to access not only
memory mapped FPGA in a generic way.
Thanks to Wolfgang Denk for getting this sorted properly.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Conflict over SPDX changes means that one change was effectively dropped
as it was fixing typos in a removed hunk of text.
Conflicts:
arch/mips/cpu/mips64/start.S
Signed-off-by: Tom Rini <trini@ti.com>
Restrict autoboot interruption to "s" or "d" keys. This will prevent some
unwanted stopping and also allow disabling the reset on command timeout.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Accessing powered down peripherals will hang the bus, so check power
domain status before initializing SATA and fixup the FDT to disable
unused peripherals.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Various changes to highbank config:
Enable EFI partitions
Enable ext4 and FAT filesystems
Enable bootz command and raw initrd
Increase cmd and print buffer size to 1K
Change serial baudrate to 115200
Enable hush shell
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.
The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.
This is enough to boot U-Boot to the command prompt
both in little and big endian mode.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
Pull all the duplicate configuration options into configs/mxs.h
from the board configuration files. This reduces the files greatly
and makes them somewhat more readable. Besides, we do no longer
have such a horrible duplication of code.
Note that the mx23evk grew in size slightly. This is due to the
CONFIG_SYS_CBSIZE now being set to 1024 as it is on the rest of
MXS systems.
This patch also fixes the OCRAM size for i.MX23. The i.MX23 has
only 32kB of OCRAM, while i.MX28 has 128kB of OCRAM.
I verified the configuration didn't change for each of the boards,
but I didn't boot-test it on the boards I do not have. I configured
U-Boot for each board using the "make ... <board>_config" command
and then ran "cpp -I include -dM include/config.h" , which dumped
all the configuration options. I did this both before and after this
patch and finally compared the results for each MXS board. Actually,
the results do differ slightly, since the configs/mxs.h file now
properly includes the correct iomux-mx23.h or iomux-mx28.h , so
while comparing, I had to ignore these new defines. These have no
impact on U-Boot configuration though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add a header file, setup.h, which copy from Linux source code,
this file contain structures are used to pass initialisation parameters
to Linux. Enable this function on adp-ag101/adp-ag101p target
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
The original adp-ag101/adp-ag101p initialize only one bank(64MB)
by default at boot time, but it is not enough for some application,
so increasing to two banks(128M).
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Cc: Macpaul Lin <macpaul@gmail.com>
Due to the new I2C framework we need to adapt the u-boot update
function. Due to the new framework all i2c leafs behind a mux are
present in the system and not only those who are defined and used. So it
is bus number 5 after the rework.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This enables CONFIG_SYS_I2C on Tegra, updating existing boards and the Tegra
i2c driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
as the keymile boards use now the new i2c multibus/multiadapter
framework, remove the EEprom_ivm Environmentvar, as not longer
needed.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-By: Holger Brunck <holger.brunck@keymile.com>
- added to fsl_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
- added to soft_i2c driver new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Missing space for loaddtb command has been added. When missing, ext4load
fails with wrong number of passed parameters.
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2x GbE
- Lattice ECP3 FPGA connected via PCIe
- mSATA RAID1
- USB host
- DisplayPort video output
- Atmel TPM
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The files board/qi/qi_lb60/qi_lb60.c and include/configs/qi_lb60.h were
licensed under the GPL v3 or later, and not v2 or later. As this is
incompatible with the project, revert this board support until the
responsible parties are available to re-license (if so desired) under
GPL v2.
Signed-off-by: Tom Rini <trini@ti.com>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Jason Liu <r64343@freescale.com>
this is usefull when writing an UBI image which contains
and UBIFS volume (check README.nand and UBI FAQ for more
details)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add USB EHCI, storage and network support.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit:
dfu: make data buffer size configurable
SHA1: 89a72b2e0e141042c9109185e02d39b2107ffc62
replaced statically allocated buffers with one allocated with memalign.
Malloc pool size of 1MiB was too small, since we needed bigger buffer to
transfer for example uImage.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch performs the following:
1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.
TEST: Tested SD-MMC boot on SMDK5250 and Origen.
Tested USB and SPI boot on SMDK5250
Compile tested for SMDKV310.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
smdk5250-uboot-spl.lds is moved to common folder, so that it can be reused.
It is renamed to exynos-uboot-spl.lds
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We've been dropping SoC name from U-Boot prompt as it increase
complexity for automatic testing and makes line longer for no good
reason.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
This adds a default environment which should be able to support both
3.0.15 from Timesys and upcoming 3.11.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
In a714321 we add a check at the end of findfdt to make sure we have
updated it from undefined and if not, warn the user. This however
forgot a ';' on the end of the previous last test.
Signed-off-by: Tom Rini <trini@ti.com>
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Add tracing to Exynos5 boards, so that tracing can be enabled when building
with 'make FTRACE=1'. We use a 16MB trace buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support tracing on sandbox by adding suitable CONFIG options. To enable it,
compile U-Boot with FTRACE=1.
The timer functions are marked to skip tracing, since these are called from
the tracing code itself, and we want to avoid an infinite loop.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch initiates cros-ec in board_init() to enable it for smdk5250.
This patch depends on the patch in the MMC series that brings in exynos5-dt.c.
Refer to http://patchwork.ozlabs.org/patch/240084.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
add network support with ksz8851_16mll on at91sam9n12ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
- remove the builtin 'rootpath' spec (according to U-Boot project
policy) and require user provided environments to contain these
- rephrase the evaluation of the 'muster_nr' approach which allows to
quickly switch among several network boot setups (make the setting
transparent when empty, resulting in default DULG behaviour)
- reduce the ARP timeout for faster network boot
Signed-off-by: Gerhard Sittig <gsi@denx.de>
- use the default baudrate table for serial communication
- remove hostname/boofile/rootpath defines which were not referenced elsewhere
Signed-off-by: Gerhard Sittig <gsi@denx.de>
This patch enables CONFIG_SILENT_CONSOLE for EXYNOS5.
This patch also removes the hardcoding of UART port from
exynos5250 config.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for the Palm Treo 680 smartphone. A quick overview of
u-boot implementation on the treo 680...
The treo 680 has a Diskonchip G4 nand flash chip. This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device. The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL). At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it. The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used. To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image. That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.
The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward. I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).
Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen. But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
There will need the environment in SPL for reasons other than network
support (in particular, hwconfig contains info for how to set up DDR).
Add a new symbol CONFIG_SPL_ENV_SUPPORT to replace CONFIG_SPL_NET_SUPPORT
for environment in common/Makefile.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Relax parameters to give address latching more time to setup.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4 can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.
You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
B4860QDS can support the feature of Boot from SRIO/PCIE, and the macro
"CONFIG_SRIO_PCIE_BOOT_MASTER" will enable the master module of this feature
when building the u-boot image.
You can get some description about this macro in README file, and for more
information about the feature of Boot from SRIO/PCIE, please refer to the
document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.
Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB has 1GB DDR.
Out of this, only 880MB is passed on to Linux via bootm_size.
Remaining
-16MB is reserved for PowerPC-DSP shared control area
-128MB is reserved for DSP private area.
Also 256MB, out of this 880MB is required for data communication between
PowerPC and DSP core.
For this bootargs are modified to pass parameter to create 1 hugetlb
page of 256MB via default_hugepagesz, hugepagesz and hugepages
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB supports Sysclk
-66MHz if jumper J16 is close (default state)
-100MHz if jumper J16 is open
Add targets
-BSC9131RDB_NAND_SYSCLK100 : for NAND boot at Sysclk 100MHz
-BSC9131RDB_SPIFLASH_SYSCLK100: for SPI boot at Sysclk 100MHz
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
IFC errata A003399 is valid for IFC NOR boot i.e.if no on-board NOR flash or
no NOR boot, do not compile its workaround.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
