Commit graph

89 commits

Author SHA1 Message Date
Tom Rini
1cb9cb3ec0 Merge branch 'master' of git://www.denx.de/git/u-boot-microblaze 2016-06-06 07:16:39 -04:00
Michal Simek
340b0e3bb6 env: Setup GD_FLG_ENV_DEFAULT flag when default environment are used
Setup flag when default environment are used to be able to
rewrite default distro boot variables based on SoC boot mode.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
2016-06-06 11:23:27 +02:00
mario.six@gdsys.cc
53ecdfb920 dm: gpio: Add methods for open drain setting
Certain GPIO devices have the capability to switch their GPIOs into
open-drain mode, that is, instead of actively driving the output
(Push-pull output), the pin is connected to the collector (for a NPN
transistor) or the drain (for a MOSFET) of a transistor, respectively.
The pin then either forms an open circuit or a connection to ground,
depending on the state of the transistor.

This patch adds functions to the GPIO uclass to switch GPIOs to
open-drain mode on devices that support it.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-03 22:13:52 -07:00
Eric Nelson
6c880b7719 dm: gpio: add a default gpio xlate routine
Many drivers use a common form of offset + flags for device
tree nodes. e.g.:
	<&gpio1 2 GPIO_ACTIVE_LOW>

This patch adds a common implementation of this type of parsing
and calls it when a gpio driver doesn't supply its' own xlate
routine.

This will allow removal of the driver-specific versions in a
handful of drivers and simplify the addition of new drivers.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
2016-05-17 09:54:43 -06:00
Simon Glass
17c43f1a42 gpio: Use const where possible
Some functions do not change the struct gpio_desc parameter. Update these to
use const so this is clear.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17 10:27:22 +08:00
Simon Glass
bbf2478026 gpio: Add a function to obtain a GPIO vector value
We can use GPIOs as binary digits for reading 'strapping' values. Each GPIO
is assigned a single bit and can be set high or low on the circuit board. We
already have a legacy function for reading these values. Add one that
supports driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-03-17 10:27:22 +08:00
David Müller (ELSOFT AG)
928f605455 Remove unused CONFIG_MODEM_SUPPORT option and associated dead code.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
2016-02-08 10:22:44 -05:00
Bin Meng
a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
Simon Glass
5a54194515 dm: common: Add memory reservation for the video uclass
Before relocation we need to reserve memory for the video driver frame
buffers so that they can use this memory when they start up (after
relocation). Add a call to the uclass to permit this.

The current top and bottom of the region is stored in global_data so that
it can be checked post-relocation to ensure enough memory is available. No
video device should be probed before relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2016-01-20 19:10:15 -07:00
York Sun
e81495224f Reserve secure memory
Secure memory is at the end of memory, separated and reserved
from OS, tracked by gd->secure_ram. Secure memory can host
MMU tables, security monitor, etc. This is different from PRAM
used to reserve private memory. PRAM offers memory at the top
of u-boot memory, not necessarily the real end of memory for
systems with very large DDR. Using the end of memory simplifies
MMU setup and avoid memory fragmentation.

"bdinfo" command shows gd->secure_ram value if this memory is
marked as secured.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:32 +08:00
Simon Glass
9854a8748c console: Add a console buffer
It is useful to be able to record console output and provide console input
via a buffer. This provides sandbox with the ability to run a command and
check its output. If the console is set to silent then no visible output
is generated.

This also provides a means to fix the problem where tests produce unwanted
output, such as errors or warnings. This can be confusing. We can instead
set the console to silent and record this output. It can be checked later
in the test if required.

It is possible that this may prove useful for non-test situations. For
example the console output may be suppressed for normal operations, but
recorded and stored for access by the OS. That feature is not implemented
at present.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-11-19 20:27:50 -07:00
Fabio Estevam
77c8554e4d include: Add generic bitops headers
Use the generic bitops header files from the kernel.

Imported from kernel 4.2.3.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-11-05 10:51:57 -05:00
Simon Glass
1017296247 dm: spl: Support device tree when BSS is in a different section
At present in SPL we place the device tree immediately after BSS. This
avoids needing to copy it out of the way before BSS can be used. However on
some boards BSS is not placed with the image - e.g. it can be in RAM if
available.

Add an option to tell U-Boot that the device tree should be placed at the
end of the image binary (_image_binary_end) instead of at the end of BSS.

Note: A common reason to place BSS in RAM is to support the FAT filesystem.
We should update the code so that it does not use so much BSS.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-11-04 14:49:52 +01:00
Thomas Chou
c8a7ba9e6a dm: implement a Timer uclass
Implement a Timer uclass to work with lib/time.c.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
2015-10-23 07:37:03 +08:00
Jagan Teki
89b5c81b75 linux/bitops.h: GENMASK copy from linux
GENMASK is used to create a contiguous bitmask([hi:lo]).

This patch is a copy from Linux, with below commit details
"bitops: Fix shift overflow in GENMASK macros"
(sha1: 00b4d9a14125f1e51874def2b9de6092e007412d)

Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
2015-10-21 09:14:07 -04:00
Simon Glass
2212e69bc0 Revert "Align global_data to a 16-byte boundary"
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.

The fix is not complicated but it seems safer to revert this for now.

This reverts commit 2afddae075.
Signed-off-by: Simon Glass <sjg@chromium.org>
2015-08-17 17:19:18 -04:00
Simon Glass
2afddae075 Align global_data to a 16-byte boundary
Some archs like to have larger alignment for their global data. Use 16 bytes
which suits all current archs.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 09:50:07 -06:00
Bin Meng
715f599f8a common: Display >=4GiB memory bank size
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-14 03:24:20 -06:00
Simon Glass
f05ad9ba4c Add a way to skip relocation
When running U-Boot as an EFI application we cannot relocate since we do not
have relocation information. U-Boot has already been relocated to a suitable
address.

Add a global_data flag to control skipping relocation.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:43:46 -06:00
Simon Glass
b0b403d954 Reserve the top 16 flag bits for architecture-specific use
Add a convention that the generic global_data only occupy the bottom 16 bits
of the flags word, so that there is less chance of a conflict. At present the
x86 flags conflict.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-05 08:42:40 -06:00
Simon Glass
070d00b8dc dm: spl: Allow device tree/driver model in board_init_f()
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.

Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:28 -06:00
Simon Glass
efa677fb48 dm: gpio: Add dm_gpio_request() to manually request a GPIO
This function can be used for testing to manually request a GPIO for use,
without resorting to the legacy GPIO API.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:23 -06:00
Simon Glass
32ec159844 dm: gpio: Add dm_gpio_lookup_name() to look up a GPIO name
Provide a driver-model function to look up a GPIO name. Make the standard
function use it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-07-21 17:39:23 -06:00
Simon Glass
b9da5086b8 dm: x86: baytrail: Correct PCI region 3 when driver model is used
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-07-14 18:03:19 -06:00
Masahiro Yamada
d9a607f2bd gpio: fix typos in GPIO header
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-06-04 03:38:05 -06:00
Simon Glass
f9523961b0 dm: gpio: Fix comment typo in GPIOD_IS_IN
This should say 'in', not 'out'.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-05-14 18:49:34 -06:00
Simon Glass
962f5caf60 dm: gpio: Add error handling and a function to claim vector GPIOs
gpio_get_values_as_int() should return an error if something goes wrong.
Also provide gpio_claim_vector(), a function to request the GPIOs and set
them to input mode. Otherwise callers have to do this themselves.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:06 -07:00
Alison Wang
1313db48e2 m68k: Add generic board support for MCF547X/8X and MCF5445X
This patch adds generic board support for MCF547X/8X and MCF5445X.
It is based on the patch about common generic board support for
M68K architecture sent by Angelo.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2015-03-05 20:13:22 -05:00
angelo@sysam.it
e310b93ec1 m68k: add generic-board support
Add generic-board support for the m68k architecture.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2015-03-05 20:13:21 -05:00
Andreas Bießmann
a752a8b4c4 avr32: add generic board support
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-17 22:54:38 +01:00
Tom Rini
7f641d53bb Merge branch 'master' of git://git.denx.de/u-boot-ubi 2015-02-04 13:30:00 -05:00
Martin Dorwig
49cad54788 Export redesign
this is an atempt to make the export of functions typesafe.
I replaced the jumptable void ** by a struct (jt_funcs) with function pointers.
The EXPORT_FUNC macro now has 3 fixed parameters and one
variadic parameter
The first is the name of the exported function,
the rest of the parameters are used to format a functionpointer
in the jumptable,

the EXPORT_FUNC macros are expanded three times,
1. to declare the members of the struct
2. to initialize the structmember pointers
3. to call the functions in stubs.c

Signed-off-by: Martin Dorwig <dorwig@tetronik.com>
Acked-by: Simon Glass <sjg@chromium.org>

Signed-off-by: Simon Glass <sjg@chromium.org>
(resending to the list since my tweaks are not quite trivial)
2015-01-29 17:09:57 -07:00
Simon Glass
5d1c17e9a5 dm: gpio: Mark the old GPIO API deprecated
Add a deprecation notice to each function so that it is more obvious that we
are moving GPIOs to driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:51 -07:00
Simon Glass
3669e0e759 dm: gpio: Add better functions to request GPIOs
At present U-Boot sort-of supports the standard way of reading GPIOs from
device tree nodes, but the support is incomplete, a bit clunky and only
works for GPIO bindings where #gpio-cells is 2.

Add new functions to request GPIOs, taking full account of the device
tree binding. These permit requesting a GPIO with a simple call like:

   gpio_request_by_name(dev, "cd-gpios", 0, &desc, GPIOD_IS_IN);

This will request the GPIO, looking at the device's node which might be
this, for example:

   cd-gpios = <&gpio TEGRA_GPIO(B, 3) GPIO_ACTIVE_LOW>;

The GPIO will be set to input mode in this case and polarity will be
honoured by the GPIO calls.

It is also possible to request and free a list of GPIOs.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:51 -07:00
Simon Glass
0dac4d51f5 dm: gpio: Add a driver GPIO translation method
Only the GPIO driver knows about the full GPIO device tree binding used by
a device. Add a method to allow the driver to provide this information to the
uclass, including the GPIO offset within the device and flags such as the
polarity.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:50 -07:00
Simon Glass
ae7123f876 dm: gpio: Add a native driver model API
So far driver model's GPIO uclass just implements the existing GPIO API.
This has some limitations:

- it requires manual device tree munging to support GPIOs in device tree
    (fdtdec_get_gpio() and friends)
- it does not understand polarity
- it is somewhat slower since we must scan for the GPIO device each time
- Global GPIO numbering can change if other GPIO drivers are probed
- it requires extra steps to set the GPIO direction and value

The new functions have a dm_ prefix where necessary to avoid name conflicts
but we can remove that when it is no-longer needed. The new struct gpio_desc
holds all required information about the GPIO. For now this is intended to
be stored by the client requesting the GPIO, but in future it might be
brought into the uclass in some way.

With these changes the old GPIO API still works, and uses the driver model
API underneath.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:50 -07:00
Anton Habegger
dc2884315d ubifs: Import atomic_long operations from Linux
This commit is a preperation for a subsequent UBIFS commit
which needs atomic_long operations.

Therefor "include/asm-generic/atomic-long.h" is imported
from 1860e37 Linux 3.15

Signed-off-by: Anton Habegger <anton.habegger@gmail.com>
2015-01-28 07:42:35 +01:00
Bin Meng
8f9052fd98 pci: Make pci apis usable before relocation
Introduce a gd->hose to save the pci hose in the early phase so that
apis in drivers/pci/pci.c can be used before relocation. Architecture
codes need assign a valid gd->hose in the early phase.

Some variables are declared as static so change them to be either
stack variable or global data member so that they can be used before
relocation, except the 'indent' used by CONFIG_PCI_SCAN_SHOW which
just affects some print format.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-01-12 17:03:41 -08:00
Tom Rini
1739564e75 Merge git://git.denx.de/u-boot-dm
Conflicts:
	drivers/serial/serial-uclass.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-11-24 12:01:48 -05:00
Simon Glass
c9356be307 dm: Split the simple malloc() implementation into its own file
The simple malloc() implementation is used when memory is tight. It provides
a simple buffer with an incrementing pointer.

At present the implementation is inside dlmalloc. Move it into its own file
so that it is easier to find.

Rather than using relocation as a signal that the full malloc() is
available, add a special GD_FLG_FULL_MALLOC_INIT flag. This signals that the
simple malloc() should no longer be used.

In some cases, such as SPL, even the code space used by the full malloc() is
wasteful. Add a CONFIG_SYS_MALLOC_SIMPLE option to provide only the simple
malloc. In this case the full malloc is not available at all. It saves about
1KB of code space and about 0.5KB of data on Thumb 2.

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 08:12:28 +01:00
Simon Glass
e5901c94e3 dm: gpio: Add a function to read an ID from a list of GPIOs
For board IDs a common approach is to set aside several GPIOs for use in
determining the board ID. This can provide information about board features
and the revision.

Add a function that turns a list of GPIOs into an integer by assigning
each GPIO to a single bit.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:24:11 +01:00
Simon Glass
469a579df2 dm: serial: Move current serial port pointer to global_data
In general we can't store things in the data section until we have inited
SDRAM. Some platforms allow this (e.g. those with SPL) but some don't. Move
the pointer to global_data so that it will work on all platforms.

Without this fix the serial port will not work prior to relocation with
driver model on some platforms.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 07:24:11 +01:00
Marek Vasut
5038d7f189 ppc: Zap Hymod board
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.

This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
2014-10-27 14:35:55 +01:00
Tom Rini
84a6df09c7 Merge git://git.denx.de/u-boot-dm
Fix a trivial conflict over adding <dm.h>

Conflicts:
	arch/arm/cpu/armv7/omap3/board.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-10-26 14:03:08 -04:00
Jeroen Hofstee
5b5ac64560 gpio: add protype for name_to_gpio
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 15:27:36 -04:00
Simon Glass
85bfe6e4f6 dm: gpio: Remove unused get_state() uclass method
This is no longer used so drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-23 19:30:51 -06:00
Simon Glass
d44f597b12 dm: gpio: Add gpio_requestf() helper for printf() strings
Add a helper which permits a printf()-style format string for the requester
string.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-23 19:29:52 -06:00
Simon Glass
0757535a7e dm: Move the function for getting GPIO status into the uclass
This function can be more easily tested if it is in the uclass.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-23 19:29:52 -06:00
Simon Glass
6449a506d6 dm: gpio: Add gpio_get_function() and friends
Add helpers to the uclass to allow finding out the pin function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-23 19:29:52 -06:00
Simon Glass
b892d127ff dm: gpio: Implement GPIO reservation in the uclass
We have several GPIO drivers now and all are doing similar things to record
which GPIOs are reserved.

Move this logic into the uclass to make the drivers similar.

We retain the request()/free() methods since currently one driver does use
these for setting up the pin.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-10-23 19:29:51 -06:00