Add basic support for the DENX M53EVK board. Currently supported is:
MMC (incl. booting)
NAND (incl. booting)
Ethernet, I2C, USB, SATA, RTC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from
Freescale, which results in much better stability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When P1021RDB-PC reboot system, the board will hung at uboot DDR
configuration. For P1021RDB-PC DDR reset pin is multiplex with
QE, so uboot will reserve this pin for QE and skip DDR reset.
Other platforms without QE will do this reset. This patch adds
a slight code to reset DDR chip by QE CE_PB8 pin for NAND and
NOR FLASH boot. For booting from SPI FALSH and SD card, it
seems possible to use the rom on chip to write to the GPIO
pins before configuring the DDR.
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Change flexcan compatible string from "fsl,flexcan-v1.0"
to "fsl,p1010-flexcan" to match the device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add the tlb entries based on the configuration of the SRIO interfaces.
Every SRIO interface has 256M space:
#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000
#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull
#define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000
#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add defines needed to access NAND, remove second flash bank that is
actually connected to NAND.
Add nand booting support for P1022DS with hardcoded DDR config using
SPL framework from 2011
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For linux 3.x, the size of each item in interrupt-map property is 9 not 7.
Don't use the static value and calculate the size with following cells:
PCI #address-cells, PCI #interrupt-cells,
PIC address, PIC #address-cells, PIC #interrupt-cells.
Signed-off-by: Bin Jiang <bin.jiang@windriver.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The changes to a3m071/a4m2k in summary are:
- Enable CAN1 on I2C in GPS Port Configuration
- Enable SPI on PSC2
- Activate network console
- New flash partitioning
- Fix some typos
- Pass host name to Linux
- Change rootfs to squashfs,jffs2
- Enable UBI/UBIFS support
- Enable FIT support
Signed-off-by: Stefan Roese <sr@denx.de>
This patch add support for storing the environment redundant on
mmc devices. Substantially it re-uses the logic from the NAND implementation,
that means using an incremental counter for marking newer data.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO
Do not enable emio for this standard board configuration for now.
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add all fixed addresses to hardware.h and change petalinux
configuration to support this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Fix microblaze soft reset function and disable
all cpu features. Especially disable caches because
IRQs were off by disable_interrupts().
Reported-by: John Williams <john.williams@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove CONFIG_SYS_RESET_ADDRESS macro.
It was there from historical point of view
when soft reset was just jump to u-boot text start
(not used right now).
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PUE requires PKE to mean something, as do pull values with PUE, so do not
compell users to explicitly use PKE and PUE everywhere. This is also what is
done on Linux and what has already been done for i.MX51.
By the way, remove some unused pad control definitions.
There is no change of behavior.
Note that SPI_PAD_CTRL was defined by several boards with a pull value, but
without PKE or PUE, which means that no pull was actually enabled in the pad.
This might be a bug in those boards, but this patch does not change the
behavior, so it just removes the meaningless pull value from those definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
IIM:
- Homogenize prg_p naming (the reference manuals are not always self-consistent
for that).
- Add missing SCSx and bank registers.
- Fix the number of banks on i.MX53.
OCOTP:
- Rename iim to ocotp in order to avoid confusion.
- Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the
reference manual.
- Merge the existing spinoff gp1 fuse definition on i.MX6.
- Fix the number of banks on i.MX6.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Stefano Babic <sbabic@denx.de>
imx-regs.h is more appropriate location for containing register masks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Allow use of the carrier board MicroSD card available in the
Wandboard; this allow for loading alternative system from the other
card for testing or upgrade proposes.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add support to identify if the card is connected or not; so it
does not try to communicate with the controller if no card is
available.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
CKO1 drives sgtl5000 codec clock on nitrogen boards and wandboard.
Doing this setup in the bootloader will allow us to remove a lot of code in
arch/arm/mach-imx/mach-imx6q.c from the mainline kernel.
Also, according to Eric Nelson: "enabling the clock <in the bootloader> will
remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Setup CCM_CCOSR register to provide a CKO1 clock frequency of 16.5 MHz.
CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the
bootloader will allow us to remove a lot of code in arch/arm/mach-imx/mach-imx6q.c
from the mainline kernel.
mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for
this board as well.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Titanium is a i.MX6 based board from ProjectionDesign / Barco. This
patch adds support for this board with the newly introduced NAND
support for i.MX6.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch adds the fast booting LWMON5 derivat "lcd4_lwmon5".
Its a stripped down version of the full blown lwmon5 support,
without ECC, USB, POST and some other stuff. It used the newly
introduced SPL infrastrucure for SPL from NOR flash booting
on the PPC4xx.
By setting the environment variable "boot_os" to "yes", Linux
will be started from the SPL version. If not, the "normal"
U-Boot will be started.
Signed-off-by: Stefan Roese <sr@denx.de>
Snow is missing a TMU node, and with TMU support this is not allowed, so it
fails to boot. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos5250 supports secondary USB device boot mode. If the iROM fails
to download u-boot from the primary boot device (such as SD or eMMC),
it will try to retrieve from the secondary boot device (such as USB).
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu.
Add a Beaver build so it can begin to be differentiated, if need be.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
As suggested by Stephen Warren, use tegra_get_chip() to return
the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for
Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true
function, i.e. tegra_get_chip_sku(), which returns an ID like
TEGRA_SOC_T25, TEGRA_SOC_T33, etc.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Move the nand-controller node to the tegra20-tamonten.dtsi so that it
can be shared between all derived boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This target wants to check full SPL size, BSS included.
Remove CONFIG_SPL_MAX_SIZE definition and instead define
CONFIG_SPL_MAX_FOOTPRINT.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Commit 3ebd1cbc introduced compiler-generated __bss_start
and __bss_end__ and commit c23561e7 rewrote all __bss_end__
as __bss_end. Their merge caused silent and harmless but
potentially bug-inducing clashes between compiler- and linker-
generated __bss_end symbols.
Make __bss_end and __bss_start compiler-only, and create
__bss_base and __bss_limit for linker-only use.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The migration of boards from Makefile to boards.cfg was due for v2012.03, but
smdk6400 did not follow, and it does not build, so move it to scrapyard. It will
still be possible to restore it from the Git history before fixing it.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Commit e05e5de7fa made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca72, but applied to all ARM start.S.
This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB
pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.
eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this
board, which satisfies the 30-ns NF R/W cycle requirement.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
In the current u-boot, the device pin multiplexing and clock
initialisation needs to be early during the boot process and before
board_init() is called. U-boot is currently crashing on this board
because this is not being done early enough. Therefore, add a s_init()
function for the omap5912-osk board to do this.
Also fix the stack pointer so that it is pointing to the end of the
internal RAM and not the beginning as this was also causing the device
to crash.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The omap5912-osk board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash at address
0x00000000.
The omap5912-osk board only has 32MB of RAM and so fix the comment
in the omap5912-osk config.mk file as well.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The size of the DRAM for the omap5912-osk board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap5912-osk board and setup the
DRAM size there.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
After further testing we can run DDR at 400MHz so update the timings
again.
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tom Rini <trini@ti.com>
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
The omap5-uevm is the reference board name for OMAP5 soc
based platform. So rename it accordingly.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.
Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The size of the DRAM for the omap2420-h4 board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap2420-h4 board and setup the
DRAM size there.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
arch/arm/include/asm/arch-am33xx/omap_gpmc.h and
arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate
the common parts into a new header.
Introduce a new asm/omap_gpmc.h which defines the command part and pulls in
the architecture specific one.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
This is done already for am335x in
59dcf970d1 and also applies for pcm051.
It powers down the IO receiver when not performing read which helps
reducing the overall power consuption in low power states
(suspend/standby).
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
board/freescale/mx6qsabrelite/README explain a procedure to
update the SPI-NOR on the SabreLite board without Freescale
manufacturing tool but following this procedure leads to both
"sf erase" and "sf write" failing on a mx6qsabrelite board:
MX6QSABRELITE U-Boot > sf probe 1
MX6QSABRELITE U-Boot > sf erase 0 0x40000
SPI flash erase failed
MX6QSABRELITE U-Boot > sf write 0x10800000 0 0x40000
SPI flash write failed
This is because the chip-select 1 is wrong and the correct
value is 0x7300.
Since commit c1173bd0 ("sf command: allow default bus and chip selects")
the chip-select and bus arguments for the sf probe command are optional
so let's just remove it and use "sf probe" instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
When booting a Freescale kernel 3.0.35 on a Wandboard solo, the get_board_rev()
returns 0x62xxx, which is not a value understood by the VPU
(Video Processing Unit) library in the kernel and causes the video playback to
fail.
The expected values for get_board_rev are:
0x63xxx: For mx6quad/dual
0x61xxx: For mx6dual-lite/solo
So adjust get_board_rev() accordingly and make it as weak function, so that we
do not need to define it in every mx6 board file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
Maximum bus width supported by some i.MX6 boards is not 8bit like
others. In case where both host controller and card support 8bit transfers,
they agree to communicate on 8bit interface while some boards support only 4bit interface.
Due to this reason the mmc 8bit default mode fails on these boards. To rectify this,
define maximum bus width supported by these boards (4bit). If max_bus_width is not
defined, it is 0 by default and 8bit width support will be enabled in host
capabilities otherwise host capabilities are modified accordingly.
It is tested with a MMCplus card.
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
cc: stefano Babic <sbabic@denx.de>
cc: Andy Fleming <afleming@gmail.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Adds support for 'bmode' command which let user to choose where to
boot from; this allows U-Boot to load system from another storage
without messing with jumpers.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This documents the SD card identifier so it is easier for user to spot
which card number will be used, if need.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Simon Glass' commit 3929fb0a14,
which changed all occurrences of __bss__end__ into __bss_end,
left behind some untouched __bss_end__ occurrences in all 33
u-boot.lds.debug files, in board/mousse/u-boot.lds.ram and
in board/mousse/u-boot.lds.rom. These are replaced here.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
MPLL is selected as the source clk of pwm by default
Test with command "sf probe 1:0; time sf read 40008000 0 1000".
Try with different numbers of bytes and see that sane values are obtained
Build and boot U-boot with this patch, backlight works properly.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We intended to clear the bits of CLK_SRC_TOP2 register, instead we were
writing on the reserved bits of src_core1 register. Since the default
value of clk_src_top2 register were itself zero, this typo was not
creating any big issue. But it is better to fix this error for better
readability of the code.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Selecting menu items is currently done in menu_interactive_choice()
by reading the user input strings from standard input.
Extend menu_interactive_choice() to support user defined function
for selecting menu items. This function and its argument can be
specified when creating the menu.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The condition for testing of PLL getting locked was incorrect. Rectify
this error in this patch.
Reported-by: Alexei Fedorov <alexie.fedorov@arm.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Compiling for non-dt systems gives folowing warning:
smdk5250.c: In function 'board_eth_init':
smdk5250.c:152:6: warning: unused variable 'node' [-Wunused-variable]
Declare variable 'node' only for dt enabled systems to remove this
warning.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since we have DT support in exynos_fb and exynos_dp drivers now,
we need not define any static structure or platform data related to
display in the board file smdk5250.c.
So, we place the already existing structures inside #ifndef CONFIG_OF_CONTROL block.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add DT bindings for DP supporting an eDP panel of size 2560x1600.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add DT bindings for FIMD supporting an eDP panel of size 2560x1600.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replaced the functionality of callbacks by using a standard set of functions.
Instead of implementing and hooking up a callback, put the same code in one of
the standard set of functions by overriding it.
This patch is tested only on SMDK5250.
For Trats and universal_c210 board, it is only compile tested.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
T114 requires SD bus power-rail bringup for the SDIO card on SDMMC3.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
SDIO1 (the SD-card slot on Dalmore) needs to have its pads setup
before the MMC driver is added.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Dalmore has a SPI flash part attached to controller 4, so enable
controller 4 and set to 25MHz.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add a common interface to fdt based SPI drivers. Each driver is
represented by a table entry in fdt_spi_drivers[]. If there are
multiple SPI drivers in the table, the first driver to return success
from spi_init() will be registered as the SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Rename tegra SPI drivers to tegra20_flash and tegra20_slink in
preparation for commonization and addition of tegra114_spi.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This feature was only used for tegra20 seaboard that had a pinmux
conflict on the SPI pins. These boards were never manufactured, so
remove this support to clean up SPI driver.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Eliminate AM33xx specific names to prepare for TI814x support
within AM33xx-land.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Enable DDR PHY dynamic power down bit, which enables
powering down the IO receiver when not performing read.
This also helps in reducing overall power consumption in
low power states (suspend/standby).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add support for loading splash image from NAND
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>