https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r198370 | seanbright | 2009-05-30 15:36:20 -0400 (Sat, 30 May 2009) | 12 lines
Properly terminate AMI JabberSend response messages.
The response message (either Error or Success) needs an extra trailing \r\n
after the fields to inform the client that the message is complete.
(closes issue #14876)
Reported by: srt
Patches:
05302009_1.4_res_jabber.c.diff uploaded by seanbright (license 71)
asterisk_14876.patch uploaded by srt (license 378)
trunk-14876-2.diff uploaded by phsultan (license 73)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@198371 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The situation that caused this problem was when continuous mode was being
turned on and off while a rate was set for a timing interface. A very easy
way to replicate this bug was to do a Playback() from behind a Local channel.
In this scenario, a rate gets set on the channel for doing file playback.
At the same time, continuous mode gets turned on and off about every 20 ms
as frames get queued on to the PBX side channel from the other side of the
Local channel.
Essentially, this module treated continuous mode and a set rate as mutually
exclusive states for the timer to be in. When I dug deep enough, I observed
the following pattern:
1) Set timer to tick every 20 ms.
2) Wait almost 20 ms ...
3) Continuous mode gets turned on for a queued up frame
4) Continuous mode gets turned off
5) The timer goes back to its tick per 20 ms. state but starts counting
at 0 ms.
6) Goto step 2.
Sometimes, res_timing_pthread would make it 20 ms and produce a timer tick,
but not most of the time. This is what produced the choppy sound (or sometimes
no sound at all).
Now, the module treats continuous mode and a set rate as completely independent
timer modes. They can be enabled and disabled independently of each other and
things work as expected.
(closes issue #14412)
Reported by: dome
Patches:
issue14412.diff.txt uploaded by russell (license 2)
issue14412-1.6.1.0.diff.txt uploaded by russell (license 2)
Tested by: DennisD, russell
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@198146 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This commit add Calendaring support to Asterisk for iCalendar, CalDAV, and MS
Exchange calendars. Exchange support has only been tested on Exchange Server 2k3
and does not support forms-based authentication at this time (patches *very*
welcome). Exchange support is also currently missing the ability to return a
list of a meting's attendees (again, patches are very, very welcome).
Features include:
Querying a calendar for events over a specific time range
Checking a calendar's busy status via the dialplan
Writing calendar events via the dialplan (CalDAV and Exchange only)
Handling calendar event notifications through the dialplan
(closes issue #14771)
Tested by: lmadsen, twilson, Shivaprakash
Review: https://reviewboard.asterisk.org/r/58
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@197738 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r196826 | russell | 2009-05-26 13:14:36 -0500 (Tue, 26 May 2009) | 9 lines
Resolve a file handle leak.
The frames here should have always been freed. However, out of luck, there was
never any memory leaked. However, after file streams became reference counted,
this code would leak the file stream for the file being read.
(closes issue #15181)
Reported by: jkroon
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196843 65c4cc65-6c06-0410-ace0-fbb531ad65f3
'channel originate ... application <app>' CLI command.
(And yeah, I cleaned up some whitespace in res_clioriginate.c... big whoop,
wanna fight about it!?)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196758 65c4cc65-6c06-0410-ace0-fbb531ad65f3
A new xml element was created to manage the AMI actions documentation,
using AstXML.
To register a manager action using XML documentation it is now possible
using ast_manager_register_xml().
The CLI command 'manager show command' can be used to show the parsed
documentation.
Example manager xml documentation:
<manager name="ami action name" language="en_US">
<synopsis>
AMI action synopsis.
</synopsis>
<syntax>
<xi:include xpointer="xpointer(...)" /> <-- for ActionID
<parameter name="header1" required="true">
<para>Description</para>
</parameter>
...
</syntax>
<description>
<para>AMI action description</para>
</description>
<see-also>
...
</see-also>
</manager>
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196308 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Since we are dealing with a 'const char * const' now, we have to create a
temporary copy of the string to work on rather than the original. Fix inspired
by reporter. Reviewed by everyone-and-their-mother in #asterisk-dev.
(closes issue #15184)
Reported by: andrew
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196270 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds 'const' tags to a number of Asterisk APIs where they are appropriate (where the API already demanded that the function argument not be modified, but the compiler was not informed of that fact). The list includes:
- CLI command handlers
- CLI command handler arguments
- AGI command handlers
- AGI command handler arguments
- Dialplan application handler arguments
- Speech engine API function arguments
In addition, various file-scope and function-scope constant arrays got 'const' and/or 'static' qualifiers where they were missing.
Review: https://reviewboard.asterisk.org/r/251/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@196072 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In res_timer_timerfd, handle the case that set_rate gets called while a timer
is still in continuous mode. In this case, we want to remember the configured
rate, but not actually set it until continuous mode has been disabled.
Thanks to dvossel for finding and helping to debug the problem.
(closes issue #15080)
Reported by: dvossel
Tested by: dvossel
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@193718 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This branch adds additional methods to dialplan functions, whereby the result
buffers are now dynamic buffers, which can be expanded to the size of any
result. No longer are variable substitutions limited to 4095 bytes of data.
In addition, the common case of needing buffers much smaller than that will
enable substitution to only take up the amount of memory actually needed.
The existing variable substitution routines are still available, but users
of those API calls should transition to using the dynamic-buffer APIs.
Reviewboard: http://reviewboard.digium.com/r/174/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@191140 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r190661 | russell | 2009-04-27 14:00:54 -0500 (Mon, 27 Apr 2009) | 9 lines
Resolve a crash in res_smdi when used with chan_dahdi.
When chan_dahdi goes to get an SMDI message, it provides no search criteria.
It just grabs the next message that arrives. This code was written with the
SMDI dialplan functions in mind, since that is now the preferred method of
using SMDI. However, this broke support of it being used from chan_dahdi.
(closes AST-212)
........
r190662 | russell | 2009-04-27 14:03:59 -0500 (Mon, 27 Apr 2009) | 2 lines
Fix a typo from 190661.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@190663 65c4cc65-6c06-0410-ace0-fbb531ad65f3
There is a lot that could be said about this, but the patch is a big
improvement for performance, stability, code maintainability,
and ease of future code development.
The channel list is no longer an unsorted linked list. The main container
for channels is an astobj2 hash table. All of the code related to searching
for channels or iterating active channels has been rewritten. Let n be
the number of active channels. Iterating the channel list has gone from
O(n^2) to O(n). Searching for a channel by name went from O(n) to O(1).
Searching for a channel by extension is still O(n), but uses a new method
for doing so, which is more efficient.
The ast_channel object is now a reference counted object. The benefits
here are plentiful. Some benefits directly related to issues in the
previous code include:
1) When threads other than the channel thread owning a channel wanted
access to a channel, it had to hold the lock on it to ensure that it didn't
go away. This is no longer a requirement. Holding a reference is
sufficient.
2) There are places that now require less dealing with channel locks.
3) There are places where channel locks are held for much shorter periods
of time.
4) There are places where dealing with more than one channel at a time becomes
_MUCH_ easier. ChanSpy is a great example of this. Writing code in the
future that deals with multiple channels will be much easier.
Some additional information regarding channel locking and reference count
handling can be found in channel.h, where a new section has been added that
discusses some of the rules associated with it.
Mark Michelson also assisted with the development of this patch. He did the
conversion of ChanSpy and introduced a new API, ast_autochan, which makes it
much easier to deal with holding on to a channel pointer for an extended period
of time and having it get automatically updated if the channel gets masqueraded.
Mark was also a huge help in the code review process.
Thanks to David Vossel for his assistance with this branch, as well. David
did the conversion of the DAHDIScan application by making it become a wrapper
for ChanSpy internally.
The changes come from the svn/asterisk/team/russell/ast_channel_ao2 branch.
Review: http://reviewboard.digium.com/r/203/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@190423 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r189462 | seanbright | 2009-04-20 16:58:39 -0400 (Mon, 20 Apr 2009) | 13 lines
Properly handle @s within hints in AEL.
AEL was not handling the case of a device hint containing an @ symbol, which
caused parking hints (e.g. hint(park:exten@context)) to error out the parser.
This patch makes AEL treat the @ the same way it treats colon and ampersand
now, meaning the characters are included in verbatim.
(closes issue #14941)
Reported by: bpgoldsb
Patches:
bug14941.patch uploaded by seanbright (license 71)
Tested by: bpgoldsb
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@189464 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The moh_register function links an mohclass and then immediately
unrefs the class since the container now has a reference. The problem
with using realtime music on hold is that the class is allocated,
registered, and started in one fell swoop. The refcounting logic
resulted in the count being off by one. The same problem did not
happen when using a static config because the allocation and registration
of an mohclass is a separate operation from starting moh. This also did
not affect non-cached realtime moh because the classes are not registered
at all.
I also have modified res_musiconhold to use the _t_ variants of the ao2_
functions so that more info can be gleaned when attempting to trace the
refcounts. I found this to be incredibly helpful for debugging this issue
and there's no good reason to remove it.
(closes issue #14661)
Reported by: sum
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@187421 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r187045 | mmichelson | 2009-04-08 11:52:03 -0500 (Wed, 08 Apr 2009) | 10 lines
Fix a small logical error when loading moh classes.
We were unconditionally incrementing the number of mohclasses
registered. However, we should actually only increment if the
call to moh_register was successful.
While this probably has never caused problems, I noticed it
and decided to fix it anyway.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@187046 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The channel drivers which have been most heavily tested with these enhancements are
chan_sip and chan_misdn. Further work is being done to add Q.SIG support and will be
introduced in a later commit. chan_skinny has code added to it here, but according
to user pj, the support on chan_skinny is not working as of now. This will be fixed in
a later commit.
A special thanks goes out to bugtracker user gareth for getting the ball rolling and
providing the initial support for this work. Without his initial work on this, this would
not have been nearly as painless as it was.
This functionality has been tested by Digium's product quality department, as well as a
customer site running thousands of calls every day. In addition, many many many many bugtracker
users have tested this, too.
(closes issue #8824)
Reported by: gareth
Review: http://reviewboard.digium.com/r/201
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@186525 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This API provides a generic way for multiple RTP stacks to be
integrated into Asterisk. Right now there is only one present, res_rtp_asterisk,
which is the existing Asterisk RTP stack. Functionality wise this commit
performs the same as previously. API documentation can be viewed in the
rtp_engine.h header file.
Review: http://reviewboard.digium.com/r/209/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@186078 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The AGI dialplan applications did not destroy the speech structure automatically
if it was not destroyed by the running AGI script. They will now do this.
(issue LUMENVOX-15)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@184673 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This code comes from svn/asterisk/team/russell/event_performance/.
Here is a summary of the changes that have been made, in order of both
invasiveness and performance impact, from smallest to largest.
1) Asterisk 1.6.1 introduces some additional logic to be able to handle
distributed device state. This functionality comes at a cost.
One relatively minor change in this patch is that the extra processing
required for distributed device state is now completely bypassed if
it's not needed.
2) One of the things that I noticed when profiling this code was that a
_lot_ of time was spent doing string comparisons. I changed the way
strings are represented in an event to include a hash value at the front.
So, before doing a string comparison, we do an integer comparison on the
hash.
3) Finally, the code that handles the event cache has been re-written.
I tried to do this in a such a way that it had minimal impact on the API.
I did have to change one API call, though - ast_event_queue_and_cache().
However, the way it works now is nicer, IMO. Each type of event that
can be cached (MWI, device state) has its own hash table and rules for
hashing and comparing objects. This by far made the biggest impact on
performance.
For additional details regarding this code and how it was tested, please see the
review request.
(closes issue #14738)
Reported by: russell
Review: http://reviewboard.digium.com/r/205/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@184339 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r183700 | mmichelson | 2009-03-23 12:59:28 -0500 (Mon, 23 Mar 2009) | 7 lines
Fix a memory leak in res_monitor.c
The only way that this leak would occur is if Monitor were started
using the Manager interface and no File: header were given. Discovered
while reviewing the ast_channel_ao2 review request.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@183766 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r182810 | russell | 2009-03-17 21:09:13 -0500 (Tue, 17 Mar 2009) | 44 lines
Fix cases where the internal poll() was not being used when it needed to be.
We have seen a number of problems caused by poll() not working properly on
Mac OSX. If you search around, you'll find a number of references to using
select() instead of poll() to work around these issues. In Asterisk, we've
had poll.c which implements poll() using select() internally. However, we
were still getting reports of problems.
vadim investigated a bit and realized that at least on his system, even
though we were compiling in poll.o, the system poll() was still being used.
So, the primary purpose of this patch is to ensure that we're using the
internal poll() when we want it to be used.
The changes are:
1) Remove logic for when internal poll should be used from the Makefile.
Instead, put it in the configure script. The logic in the configure
script is the same as it was in the Makefile. Ideally, we would have
a functionality test for the problem, but that's not actually possible,
since we would have to be able to run an application on the _target_
system to test poll() behavior.
2) Always include poll.o in the build, but it will be empty if AST_POLL_COMPAT
is not defined.
3) Change uses of poll() throughout the source tree to ast_poll(). I feel
that it is good practice to give the API call a new name when we are
changing its behavior and not using the system version directly in all cases.
So, normally, ast_poll() is just redefined to poll(). On systems where
AST_POLL_COMPAT is defined, ast_poll() is redefined to ast_internal_poll().
4) Change poll() in main/poll.c to be ast_internal_poll().
It's worth noting that any code that still uses poll() directly will work fine
(if they worked fine before). So, for example, out of tree modules that are
using poll() will not stop working or anything. However, for modules to work
properly on Mac OSX, ast_poll() needs to be used.
(closes issue #13404)
Reported by: agalbraith
Tested by: russell, vadim
http://reviewboard.digium.com/r/198/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@182847 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r182808 | kpfleming | 2009-03-17 20:55:22 -0500 (Tue, 17 Mar 2009) | 5 lines
Improve the build system to *properly* remove unnecessary symbols from the runtime global namespace. Along the way, change the prefixes on some internal-only API calls to use a common prefix.
With these changes, for a module to export symbols into the global namespace, it must have *both* the AST_MODFLAG_GLOBAL_SYMBOLS flag and a linker script that allows the linker to leave the symbols exposed in the module's .so file (see res_odbc.exports for an example).
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@182826 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r181659 | file | 2009-03-12 13:50:37 -0300 (Thu, 12 Mar 2009) | 8 lines
Fix another scenario where depending on configuration the stream would not get read.
For custom commands we don't know whether the audio is coming from a stream or not
so we are going to have to read the data despite no channels.
(closes issue #14416)
Reported by: caspy
........
r181660 | file | 2009-03-12 13:52:45 -0300 (Thu, 12 Mar 2009) | 2 lines
Fix logic flaw in previous commit.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@181661 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r181655 | file | 2009-03-12 13:29:19 -0300 (Thu, 12 Mar 2009) | 10 lines
Fix issue with streaming MOH failing if nobody is listening.
When a music class is setup to actually provide music on hold
from a stream we need to constantly read audio from it since it
will constantly be providing audio. This is now done despite there
being no channels listening to it.
(closes issue #14416)
Reported by: caspy
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@181656 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This document specifies the timing modules available in Asterisk beginning
with Asterisk 1.6.1. The document goes into detail about the differences
between each and gives a general overview of what timing is used for in
Asterisk. There is also a section which can be used to help customize
your setup or to troubleshoot timing issues you may have.
I also added messages to the DAHDI timing test used in res_timing_dahdi.c
that points to this new documentation if people experience problems.
Big thanks to all who contributed comments on this.
(closes issue #14490)
Reported by: mmichelson
Patches:
timing.txt uploaded by mmichelson (license 60)
Review: http://reviewboard.digium.com/r/164/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@179937 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r177225 | murf | 2009-02-18 15:43:14 -0700 (Wed, 18 Feb 2009) | 34 lines
This patch fixes a regression of sorts that was introduced in
rev 24425.
It basically fixes AST-190/ABE-1782.
What was wrong: the user has 6000 extensions in one context; and
then 6000 contexts, one per extension. The parser could only handle
about 4893 of the 6000 extens in the single context.
This was due to the regression I mentioned. To get rid of
shift/reduce conflicts, Luigi set up right-recursive lists
for globals, context elements, switch lists, and statements.
Right recursive lists got rid of the warnings, but instead, they
use up a tremendous amount of stack space when the lists are long.
I saw this a few years back, and resolved not to fix it until
someone complained. That day has arrived!
After the changes were made, I ran the regression test suite,
and there were no problems.
I took the test case the user provided, and added 100,000
extensions to the single context, that already had 6,000 extens
in it. (I'll see your 6, and raise you 100!) It takes a few minutes
to read it all in, check it and generate code for it, but no
problems.
So, I think I can say that fundamentally, there are no longer
any limits on the number of items you can place in contexts,
statement blocks, switches, or globals, beyond your virt mem
constraints.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@177286 65c4cc65-6c06-0410-ace0-fbb531ad65f3
1) Add module use count handling so that timing modules can be unloaded.
2) Implement unload_module() functions for the timing interface modules.
3) Allow multiple timing modules to be loaded, and use the one with the
highest priority value.
4) Report which timing module is being use in the "timing test" CLI command.
(closes issue #14489)
Reported by: russell
Review: http://reviewboard.digium.com/r/162/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@176666 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch includes a number of changes to the indications API. The primary
motivation for this work was to improve stability. The object management
in this API was significantly flawed, and a number of trivial situations could
cause crashes.
The changes included are:
1) Remove the module res_indications. This included the critical functionality
that actually loaded the indications configuration. I have seen many people
have Asterisk problems because they accidentally did not have an
indications.conf present and loaded. Now, this code is in the core,
and Asterisk will fail to start without indications configuration.
There was one part of res_indications, the dialplan applications, which did
belong in a module, and have been moved to a new module, app_playtones.
2) Object management has been significantly changed. Tone zones are now
managed using astobj2, and it is no longer possible to crash Asterisk by
issuing a reload that destroys tone zones while they are in use.
3) The API documentation has been filled out.
4) The API has been updated to follow our naming conventions.
5) Various bits of code throughout the tree have been updated to account
for the API update.
6) Configuration parsing has been mostly re-written.
7) "Code cleanup"
The code is from svn/asterisk/team/russell/indications/.
Review: http://reviewboard.digium.com/r/149/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@176627 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r174218 | file | 2009-02-09 10:48:21 -0400 (Mon, 09 Feb 2009) | 4 lines
Don't overwrite our pointer to the music class when music on hold stops. We will use this if it starts again to see if we can resume the music where it left off.
(closes issue #14407)
Reported by: mostyn
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@174219 65c4cc65-6c06-0410-ace0-fbb531ad65f3
along the way fix some minor coding style issues in strings.h and add some attribute_pure annotations to functions in the ast_str API
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@169438 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This sequence of events posed a problem
timerfd_timer_open
timerfd_timer_enable_continuous
timerfd_timer_set_rate
timerfd_timer_disable_continuous
The reason was that the timing module was written under the assumption
that timerfd_timer_set_rate would not be called between enabling and
disabling continuous mode. What happened in this situation was that
timerfd_timer_enable_continuous saved off our previously set timer (in this
situation a 0 timer, meaning it never runs out). Then timerfd_timer_disable_continuous
would restore this 0 timer, even though it logically should set the timer to be whatever
was set in timerfd_timer_set_rate.
Now the behavior in timerfd_timer_set_rate is to overwrite the saved timer that may
or may not have been set in timerfd_timer_enable_continuous. Even if
timerfd_timer_enable_continuous has not been previously called, this will not harm the
operation.
Thanks to Terry Wilson for discovering the problem and giving me a really great debug
capture that pointed out the problem clearly
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@168898 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r168745 | murf | 2009-01-15 17:19:12 -0700 (Thu, 15 Jan 2009) | 14 lines
This patch fixes a problem where a goto (or jump, in this case)
fails a consistency check because it can't find a matching
extension. The problem was a missing instruction to end
the range notation in the code where it converts the pattern
into a regex and uses the regex code to determine the match.
I tested using the AEL code the user supplied, and now,
the consistency check passes.
(closes issue #14141)
Reported by: dimas
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@168746 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Prior to this patch, the value of AGISIGUP was not always
honored when set on a channel.
(closes issue #13711)
Reported by: fmueller
Patches:
13711.patch uploaded by putnopvut (license 60)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@166470 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch removes the usage of AST_PBX_KEEPALIVE from res_agi. The only usage
was for the AGI command, "asyncagi break". This patch removes this feature.
Normally, a feature would not be removed like this. However, this code is
broken and usage of it will result in a memory leak.
Usage of this feature will make the AGI code return a result of
AST_PBX_KEEPALIVE. The PBX handler assumes that another thread has assumed
ownership of the channel. The channel thread will exit without destroying the
channel. Unfortunately, _no_ thread has ownership of the channel at this
point. There are a couple of serious problems here:
1) The only way to recover the caller is to issue a channel redirect. This
will work, but this will be done with a masquerade, and the old ast_channel
structure will be lost.
2) Until the channel redirect happens, there is no code servicing the channel.
That means nothing is reading audio or handling events coming from the
channel. This is very bad.
The recommended way to get this same "break" functionality is to issue the
redirect while the channel is still being handled by the AGI code. That way,
there will be no memory leak, and there will be no period of time that the
channel is not being serviced.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@166258 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The variable "class" was being set NULL just prior to
being dereferenced in an ao2_link call. I have moved
the setting of the variable to NULL until after the
ao2_link call.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@165724 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r165661 | russell | 2008-12-18 12:52:18 -0600 (Thu, 18 Dec 2008) | 7 lines
Set the process group ID on the MOH process so that all children will get killed
(closes issue #14099)
Reported by: caspy
Patches:
res_musiconhold.c.patch.killpg.try2 uploaded by caspy (license 645)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@165662 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r165255 | mmichelson | 2008-12-17 14:51:38 -0600 (Wed, 17 Dec 2008) | 7 lines
Fix some memory leaks found while looking at how realtime
configs are handled.
Also cleaned up some coding guidelines violations in app_realtime.c,
mostly related to spacing
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@165318 65c4cc65-6c06-0410-ace0-fbb531ad65f3
is used while continuous mode was already turned on.
(closes issue #13738)
Reported by: smurfix
Patches:
res.patch.fixed uploaded by smurfix (license 547)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@163241 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r162874 | jpeeler | 2008-12-10 16:04:18 -0600 (Wed, 10 Dec 2008) | 5 lines
(closes issue #13229)
Reported by: clegall_proformatique
Ensure that moh_generate does not return prematurely before local_ast_moh_stop is called. Also, the sleep in mp3_spawn now only occurs for http locations since it seems to have been added originally only for failing media streams.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@162891 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r162264 | murf | 2008-12-09 13:20:54 -0700 (Tue, 09 Dec 2008) | 1 line
In discussion with seanbright on #asterisk-dev, I have added a default rule, and an option to suppress the default rule from being generated in the flex output, for the sake of those OS's where they didn't tweak flex's ECHO macro, and the compiler doesn't like it. The regressions are OK with this.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@162271 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r162013 | murf | 2008-12-09 09:31:55 -0700 (Tue, 09 Dec 2008) | 45 lines
(closes issue #14019)
Reported by: ckjohnsonme
Patches:
14019.diff uploaded by murf (license 17)
Tested by: ckjohnsonme, murf
This crash was the result of a few small errors that
would combine in 64-bit land to result in a crash.
32-bit land might have seen these combine to mysteriously
drop the args to an application call, in certain
circumstances.
Also, in trying to find this bug, I spotted
a situation in the flex input, where, in passing
back a 'word' to the parser, it would allocate
a buffer larger than necessary. I changed the
usage in such situations, so that strdup was
not used, but rather, an ast_malloc, followed
by ast_copy_string.
I removed a field from the pval struct, in
u2, that was never getting used, and set in
one spot in the code. I believe it was an
artifact of a previous fix to make switch
cases work invisibly with extens.
And, for goto's I removed a '!' from
before a strcmp, that has been there
since the initial merging of AEL2, that
might prevent the proper target of a
goto from being found. This was pretty
harmless on its own, as it would just
louse up a consistency check for users.
Many thanks to ckjohnsonme for providing
a simplified and complete set of information
about the bug, that helped considerably in
finding and fixing the problem.
Now, to get aelparse up and running again
in trunk, and out of its "horribly broken" state,
so I can run the regression suite!
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@162079 65c4cc65-6c06-0410-ace0-fbb531ad65f3
because SPRINTF() use non-literal format strings (which cannot be checked), move it into its own module so the rest of func_strings can benefit from format string checking
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@159774 65c4cc65-6c06-0410-ace0-fbb531ad65f3
They removed the LDAP_DEPRECATED define from their source and since we are using a couple
of deprecated function calls we should define it with a CFLAG.
Tested by me on OpenBSD 4.4 and snuff-home on Linux to make sure everything keeps compiling.
It shouldn't break, we only define the LDAP_DEPRECATED with this which is what
all 2.2.X and older versions of OpenLDAP did in their own tree.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@159734 65c4cc65-6c06-0410-ace0-fbb531ad65f3
it would be best to maintain API compatibility. Instead, this commit introduces
ao2_callback_data() which is functionally identical to ao2_callback() except
that it allows you to pass arbitrary data to the callback.
Reviewed by Mark Michelson via ReviewBoard:
http://reviewboard.digium.com/r/64
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@158959 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r157859 | kpfleming | 2008-11-19 15:34:47 -0600 (Wed, 19 Nov 2008) | 7 lines
the gcc optimizer frequently finds broken code (use of uninitalized variables, unreachable code, etc.), which is good. however, developers usually compile with the optimizer turned off, because if they need to debug the resulting code, optimized code makes that process very difficult. this means that we get code changes committed that weren't adequately checked over for these sorts of problems.
with this build system change, if (and only if) --enable-dev-mode was used and DONT_OPTIMIZE is turned on, when a source file is compiled it will actually be preprocessed (into a .i or .ii file), then compiled once with optimization (with the result sent to /dev/null) and again without optimization (but only if the first compile succeeded, of course).
while making these changes, i did some cleanup work in Makefile.rules to move commonly-used combinations of flag variables into their own variables, to make the file easier to read and maintain
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@157974 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This provides a new timing interface. In order to use it,
you must be running a Linux with a kernel version of
2.6.25 or newer and glibc 2.8 or newer.
This timing interface is a good alternative if a timing
source is necessary (e.g. for IAX trunking) but DAHDI is
otherwise unnecessary for the system.
For now, this commit contains the actual work done in the
res_timing_timerfd branch. There are no notices in the README
or CHANGES files yet, but they will be added in my next commit.
The timing API of Asterisk also needs to have a bit of work done
with regards to choosing which timing interface to use. This commit
makes the choice a build-time decision, by only allowing one of
the timer interfaces to be chosen in menuselect. It would be preferable
if the choice could be made at run-time, however. The preferred timing
interface could be loaded and tested, and if it does not work, choice
number two may be used instead. That sort of thing. That is beyond
the scope of work in this branch though.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@157820 65c4cc65-6c06-0410-ace0-fbb531ad65f3
also, move UPGRADE.txt to UPGRADE-1.6.txt and make the new UPGRADE.txt contain information about upgrading between Asterisk 1.6 releases
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@157706 65c4cc65-6c06-0410-ace0-fbb531ad65f3
is unloaded and then Asterisk is stopped. The problem was that
we are not unregistering the ast_moh_destroy function at exit.
(closes issue #13761)
Reported by: eliel
Patches:
res_musiconhold.c.patch uploaded by eliel (license 64)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@157592 65c4cc65-6c06-0410-ace0-fbb531ad65f3
- Add CLI aliases module to asterisk.
- Remove all deprecated CLI commands from the code
Initial work done by file.
Junk-Y and lmadsen did a lot of work and testing to
get the list of deprecated commands into the configuration file.
Deprecated CLI commands are now handled by this new module,
see cli_aliases.conf for more info about that.
ok russellb@ via reviewboard
(closes issue #13735)
Reported by: mvanbaak
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@156120 65c4cc65-6c06-0410-ace0-fbb531ad65f3
A new <agi> element is used to describe the XML documentation.
We have the usual synopsis,syntax,description and seealso for AGI commands.
The CLI 'agi show commands' command was changed to show all the documentation se
ctions.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@156051 65c4cc65-6c06-0410-ace0-fbb531ad65f3
ao2_callback and ao2_find). Currently, passing OBJ_POINTER to either
of these mandates that the passed 'arg' is a hashable object, making
searching for an ao2 object based on outside criteria difficult.
Reviewed by Russell and Mark M. via ReviewBoard:
http://reviewboard.digium.com/r/36/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@155401 65c4cc65-6c06-0410-ace0-fbb531ad65f3
along the way, change tags used in configure script, menuselect-deps and code for various dependencies to be consistently named
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@154151 65c4cc65-6c06-0410-ace0-fbb531ad65f3
'update2', which permits updates which match across multiple columns, instead
of requiring all tables to have a single unique identifier. All of the other
API calls with the exception of 'update' already had the ability to match on
multiple fields, so it was a missing and very desireable feature that an API
call implementing an update should have this, too.
This does not change any outward performance of Asterisk, but it should make
life easier for application developers who use the RealTime framework.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@148570 65c4cc65-6c06-0410-ace0-fbb531ad65f3
app_voicemail. Instead, include it where it is needed. This turned out to be a
relatively minor issue because other headers include logger.h as well.
Need to test -addons before merging this back to 1.6.0.
(closes issue #13605)
Reported by: tomo1657
Patches:
13605_seanbright.diff uploaded by seanbright (license 71)
Tested by: mmichelson
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@148200 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This allows for the ODBC parts to work on OpenBSD as well.
99.99% of the work is done by seanbright (bow, bow) and I actually
did nothing but test and yell at him that it still didn't work :)
Thanks for helping out !
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@146925 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r146799 | tilghman | 2008-10-06 15:52:04 -0500 (Mon, 06 Oct 2008) | 8 lines
Dialplan functions should not actually return 0, unless they have modified the
workspace. To signal an error (and no change to the workspace), -1 should be
returned instead.
(closes issue #13340)
Reported by: kryptolus
Patches:
20080827__bug13340__2.diff.txt uploaded by Corydon76 (license 14)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@146802 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This work is done by lmadsen, junky and mvanbaak
during AstriDevCon.
This is the second audit the CLI got, and
this time lmadsen made sure he had _ALL_ modules
loaded that have CLI commands in them.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@145121 65c4cc65-6c06-0410-ace0-fbb531ad65f3
when a file is invalid from when a file is missing. This is most important when
we have two configuration files. Consider the following example:
Old system:
sip.conf users.conf Old result New result
======== ========== ========== ==========
Missing Missing SIP doesn't load SIP doesn't load
Missing OK SIP doesn't load SIP doesn't load
Missing Invalid SIP doesn't load SIP doesn't load
OK Missing SIP loads SIP loads
OK OK SIP loads SIP loads
OK Invalid SIP loads incompletely SIP doesn't load
Invalid Missing SIP doesn't load SIP doesn't load
Invalid OK SIP doesn't load SIP doesn't load
Invalid Invalid SIP doesn't load SIP doesn't load
So in the case when users.conf doesn't load because there's a typo that
disrupts the syntax, we may only partially load users, instead of failing with
an error, which may cause some calls not to get processed. Worse yet, the old
system would do this with no indication that anything was even wrong.
(closes issue #10690)
Reported by: dtyoo
Patches:
20080716__bug10690.diff.txt uploaded by Corydon76 (license 14)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@142992 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r141094 | murf | 2008-09-04 17:15:07 -0600 (Thu, 04 Sep 2008) | 70 lines
(closes issue #13357)
Reported by: pj
Tested by: murf
(closes issue #13416)
Reported by: yarns
Tested by: murf
If you find this message overly verbose, relax, it's probably
not meant for you. This message is meant for probably only
two people in the whole world: me, or the poor schnook that
has to maintain this code because I'm either dead or unavailable
at the moment.
This fix solves two reports, both having to do with embedding
a function call in a ${} construct. It was tricky because the
funccall syntax has parenthesis () in it. And up till now,
the 'word' token in the flex stuff didn't allow that, because
it would tend to steal the LP and RP tokens. To be truthful,
the "word" token was the trickiest, most unstable thing in
the whole lexer. I was lucky it made this long without complaints.
I had to choose every character in the pattern with extreme
care, and I knew that someday I'd have to revisit it. Well,
the day has come.
So, my brilliant idea (and I'm being modest), was to use the
surrounding ${} construct to make a state machine and capture
everything in it, no matter what it contains. But, I have to now
treat the word token like I did with comments, in that I turn
the whole thing into a state-machine sort of spec, with new
contexts "curlystate", "wordstate", and "brackstate".
Wait a minute, "brackstate"? Yes, well, it didn't take very many
regression tests to point out if I do this for ${} constructs,
I also have to do it with the $[] constructs, too.
I had to create a separate pcbstack2 and pcbstack3 because
these constructs can occur inside macro argument lists, and
when we have two state machines operating on the same structures
we'd get problems otherwise. I guess I could have stopped at
pcbstack2 and had the brackstate stuff share it, but it doesn't
hurt to be safe. So, the pcbpush and pcbpop routines also now
have versions for "2" and "3".
I had to add the {KEYWORD} construct to the initial pattern for
"word", because previously word would match stuff like "default7",
because it was a longer match than the keyword "default". But,
not any more, because the word pattern only matches only one or
two characters now, and it will always lose. So, I made it the
winner again by making an optional match on any of the keywords
before it's normal pattern.
I added another regression test to make sure we don't
lose this in future edits, and had to fix just one regression,
where it no longer reports a 'cascaded' error, which I guess
is a plus.
I've given some thought as to whether to apply these fixes to
1.4 and the 1.6.x releases, vs trunk; I decided to put it in
1.4 because one of the bug reports was against 1.4; and it
is unexpected that AEL cannot handle this situation. It actually
reduced the amount of useless "cascade" error messages that
appeared in the regressions (by one line, ehhem). There is
a possible side-effect in that it does now do more careful
checking of what's in those ${} constructs, as far as matching
parens, and brackets are concerned. Some users may find a an
insidious problem and correct it this way. This should be
exceedingly rare, I hope.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@141115 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r141028 | jpeeler | 2008-09-04 12:00:29 -0500 (Thu, 04 Sep 2008) | 7 lines
(closes issue #11979)
Fixes multiple parking problems:
Crash when executing a park on an extension dialed by AGI due to not returning the proper return code.
Crash when using a builtin feature that was a subset of a enabled dynamic feature.
Crash due to always hanging up the peer despite the fact that the peer was supposed to be parked.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@141039 65c4cc65-6c06-0410-ace0-fbb531ad65f3
of changes to the Set and MSet apps, so people aren't
so shocked and surprised when they upgrade from
1.4 to 1.6.
Also, for the sake of those upgrading from 1.4 to
1.6 with AEL, I provide automatic support for the
"old" way of using Set(), that still does the
exact same old thing with quotes and backslashes
and so on as 1.4 did, by having AEL compile in the
use of MSet() instead of Set(), everywhere it inserts
this code.
But, if the app_set var is set to 1.6 or higher,
it uses the "new", non-evaluative Set().
This only usually happens if the user manually
inserts this into the asterisk.conf file, or runs
the "make samples" command.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@140824 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r140488 | mmichelson | 2008-08-29 12:34:17 -0500 (Fri, 29 Aug 2008) | 22 lines
After working on the ao2_containers branch, I noticed
something a bit strange. In all cases where we provide
a callback function to ao2_container_alloc, the callback
function would only return 0 or CMP_MATCH. After inspecting
the ao2_callback() code carefully, I found that if you're
only looking for one specific item, then you should return
CMP_MATCH | CMP_STOP. Otherwise, astobj2 will continue
traversing the current bucket until the end searching for
more matches.
In cases like chan_iax2 where in 1.4, all the peers are
shoved into a single bucket, this makes for potentially
terrible performance since the entire bucket will be
traversed even if the peer is one of the first ones come
across in the bucket.
All the changes I have made were for cases where the
callback function defined was passed to ao2_container_alloc
so that calls to ao2_find could find a unique instance
of whatever object was being stored in the container.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@140489 65c4cc65-6c06-0410-ace0-fbb531ad65f3
to the Set app in trunk/1.6.x, as they come from the 1.4 world. They are only bitten if
they write their AEL dialplan in the 1.4 world, and then carry it over to a trunk/1.6.x
installation where a "make samples" was executed, or where they hand-edited the
asterisk.conf file and added the [compat] category with app_set = 1.6 (or higher).
(this commit does not totally solve 13249, at least not yet)
The change involves issueing a single warning while the AEL file is loading, if:
1. app_set is present in the config file, and set to 1.6 or higher.
2. there are double quotes in an assignment statement (eg x = "hi there";)
3. the warning was not already issued.
The standalone app, aelparse, does not (yet) issue this warning. I'd have to
have it read in the asterisk.conf file, and that's a bit of hassle. I'll add
it if users request it, tho.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@138815 65c4cc65-6c06-0410-ace0-fbb531ad65f3
an OOB message that answers the question of, if AGI no longer shuts down the
connection on hangup, how will FastAGI know when to stop processing the call?
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@136859 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r136726 | murf | 2008-08-07 18:15:34 -0600 (Thu, 07 Aug 2008) | 32 lines
(closes issue #13236)
Reported by: korihor
Wow, this one was a challenge!
I regrouped and ran a new strategy for
setting the ~~MACRO~~ value; I set it once
per extension, up near the top. It is only
set if there is a switch in the extension.
So, I had to put in a chunk of code to detect
a switch in the pval tree.
I moved the code to insert the set of ~~exten~~
up to the beginning of the gen_prios routine,
instead of down in the switch code.
I learned that I have to push the detection
of the switches down into the code, so everywhere
I create a new exten in gen_prios, I make sure
to pass onto it the values of the mother_exten
first, and the exten next.
I had to add a couple fields to the exten
struct to accomplish this, in the ael_structs.h
file. The checked field makes it so we don't
repeat the switch search if it's been done.
I also updated the regressions.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@136746 65c4cc65-6c06-0410-ace0-fbb531ad65f3
- Changing debug messages from VERBOSE to DEBUG channel
- Adding a few todo's
- Adding a few more "XMPP"'s to compliment Jabber...
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@136005 65c4cc65-6c06-0410-ace0-fbb531ad65f3
1) If a function returns SQLITE_LOCKED, no recovery is possible.
2) An error message can be allocated, even when no error is signalled.
(closes issue #13109)
Reported by: gknispel_proformatique
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@134919 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r131242 | murf | 2008-07-16 11:53:43 -0600 (Wed, 16 Jul 2008) | 19 lines
(closes issue #13090)
Reported by: murf
The problem was that, esoteric as it is, because the hangerupper
context immediately preceded the std-priv-extent macro, that
the checking code accidentally would fall from traversing hangerupper
into the std-priv-exten macro, where it would hit the hangerupper
in the 'includes', and proceed into an infinite recursion.
A small fix to traverse into the statements of the context instead
of the context solves this issue.
I also added some commented out printfs for debug, which were pretty
handy in the face of a dorky gdb.
This was a problem around since the package was first written;
but evidently pretty rare in turning up in the field.
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@131243 65c4cc65-6c06-0410-ace0-fbb531ad65f3
released, causing a deadlock. (Reported by mvanbaak in #asterisk-dev,
discovered by bbryant's change to the lock tracking code to yell at you
if a thread exits with a lock still held)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@131072 65c4cc65-6c06-0410-ace0-fbb531ad65f3
To make sure nobody commits script-modified files we first make a backup
of asterisk.tex, run the script, generate the pdf and / or html,
and put the original asterisk.tex back.
This will guard us for the stuff that happened before that someone committed
a locally modified asterisk.tex, with changes done by this script.
(closes issue #13062)
Reported by: mvanbaak
Patches:
sed_without-i-v3.diff uploaded by mvanbaak (license 7)
Tested by: mvanbaak
Feedback from Corydon. Thanks for taking the time to go through this.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@130578 65c4cc65-6c06-0410-ace0-fbb531ad65f3