Errors returned by g_key_file_get_integer have to be deallocated
by the caller to avoid leaks like these:
==13330== 104 (24 direct, 80 indirect) bytes in 2 blocks are definitely lost
==13330== at 0x483F3EC: malloc (vg_replace_malloc.c)
==13330== by 0x4B020DF: g_malloc (gmem.c)
==13330== by 0x4B17F51: g_slice_alloc (gslice.c)
==13330== by 0x4AE80B9: g_error_new_valist (gerror.c)
==13330== by 0x4AE830B: g_set_error (gerror.c)
==13330== by 0x4AF5681: g_key_file_get_value (gkeyfile.c)
==13330== by 0x4AF6817: g_key_file_get_integer (gkeyfile.c)
==13330== by 0x10CFE3: radio_load_settings (radio-settings.c)
==13330== by 0x10D2E3: ofono_radio_settings_register (radio-settings.c)
If the ME storage is full, the modem will reject new messages
with a SMPP RP-Error 'Protocol error, unspecific'.
It seems the qmimodem is first checking the ME storage for
free space, then deliver the SMS via QMI and not saving it
to the ME anyway.
Using QMI_WMS_STORAGE_TYPE_NONE it doesn't check for free space.
Tested-on: Quectel EC20
add documentation about interface cinterion.HardwareMonitor.
This interface exposes a single method to access temperature and supply
voltage of the modem.
Gemalto modems have hardware related commands, allowing to monitor voltage
and temperature. These parameters will be accessible on DBus interface:
org.ofono.HardwareMonitor.
- Create the DBus method table with one entry: GetStatistics. This method
would return temperature and voltage values.
- Create a dedicated structure to handle the DBus methods.
- Create enable/disable functions to handle DBus interface registration.
When qmi_device_shutdown is used and the callback provided utilizes
qmi_device_unref, an access into already freed memory is triggered.
Sequence of events is:
1. timeout fires
2. glib calls timeout callback (e.g. shutdown_callback) which in turn
calls shutdown_func (gobi shutdown_cb) which in turn calls
qmi_device_unref()
3. qmi_device_unref calls g_source_remove, which doesn't call the
destroy callback (it is blocked)
4. qmi_device_unref then frees the memory used by device
5. glib then calls the source destroy callback (e.g. shutdown_destroy)
which results in just freed memory being used.
glib appears to always call the destroy callback, even if the source has
been removed previously. So to work around the issue, delay the actual
g_free until the destroy callback is invoked.
There are two problems with using pri_set_apn. The first issue is that
this function was built to be used by the set_property handler and
assumes the presence of a pending DBusMessage.
The second issue is that it touches the settings store.
In the case of auto-activated contexts no pending message exists. Also,
we should not be touching the settings store as the APN might
potentially be a value that has not been provisioned. Or in some cases
bogus.
This adds Acquire method which can be used by agents that require
pulling the fd directly instead of waiting a NewConnection.
Note: sounds servers like PulseAudio do auto suspend streams when idle
for a certain amount of time and once anything happens it will resume
the stream, though this all happens in the so called IO thread in a
blocking fashion making it impossible to receive the fd via NewConnetion
causing the stream to fail to resume. There are other forms to work
around but this seems to be most convenient as we do want the auto
suspend feature to work properly but letting the stream to fail to
resume may create unexpected artifacts while the NewConnection is
handled in main thread.
Apparently, an empty APN in an ofono context means that that the context
cannot be activated. connman definitely interprets it this way.
This patch sets a default name of "automatic" for the default bearer if
no other LTE APN is supplied (which is currently the case as the LTE
atom is not in place yet). Without this, connman happily ignores the
context, even though it has been activated by ofono.
When the modem attaches to an LTE network, a default bearer is
automatically negotiated using the "defalt profile" settings. The
QMI modem, however, does not given any explicit indication that
the bearer exists; instead, we must assume its existence based on
the network registration state.
This patch extends the GPRS atom to signal the presence of a
default bearer when it detects network connectivity on an LTE
network.
Apparently it's not legal to create a QMI service multiple times for
a device. I've been testing with a Quectel EC21 and here it works fine
to do so, but the general case would require "shared" services across
atoms.
This patch switches the users of the NAS and WDS services over to using
a "shared" service instead of each instatiating their own instance.
There are three principal ways for a context to become disconnected:
i) deactivate_primary() is called
ii) the network registration is lost and the context is cleaned up
via _detach_shutdown() (via release_all_contexts())
iii) the network decides to disconnect the context
We need to watch the packet status in order to detect case iii). For
case i) and ii), stop_net will be called, the pkt_handle will be
cleared, and subsequent packet status notifications be ignored.
This patch makes it so that the packet status "disconnected" event
is only propagated when the pkt_handle has not been cleared, indicating
an unrequested disconnection.
This should fix a race reported by Christophe Ronco whereby the packet
status disconnect notification is called between activate_primary
(start_net) and it's callback (start_net_cb).
This adds handling for ServicesResolved signal which tells when BlueZ
is done resolving the device services so the code will no longer ignore
devices that got its services resolved after Paired signal.
In case the UUIDs are not updated, as they are still being resolved, when
Paired property changes a modem will never be registered.
In order to fix this problem allow modems to be registered directly
during NewConnection.
SMS reception is not working for Gemalto modems because of +CMT parsing.
PDU length is the first argument of +CMT URCs in Gemalto modems.
Add a switch case on vendor info to handle Gemalto case.
Also handle acknowledgment, +CNMA takes only one parameter.
CMT parsing is moved from at_parse_cmt() to at_cmt_notify(). This
function is modified to match the style of at_cmgr_notify() and it
includes a switch case for CINTERION modems.
This follows the same pattern as the Telit QMI modems, routing the
setup through a QMI driver. I think this can be cleaned up somehow,
but for now this at least provides support for these two modem models
so that others can aid in testing.
This is a "leaf" header and doesn't even have header guards, but
it still seems natural that the header should pull in its own declarations
rather than relying on the including source file to ensure that they
are included.
The detach_shutdown method is invoked to unconditionally release
an active context. For QMI, this is equivalent to a call to
deactivate_primary.
This patch makes the callback to deactivate_primary optional and
implements detach_shutdown to simply call it. When there is no
callback, the stop_net callback notifies ofono about the context
release via an asynchronous ofono_gprs_context_deactivated() call.
For LTE networks, a default bearer is automatically activated when
the modem registers to the network. QMI modems, however, do not
automatically enable the network interface just because the bearer
exists; a call to "start network" needs to be made in order to
get the packet handle before get_settings will return any data and
the network interface can be configured.
This patch makes read_settings call "start network" in order to
enable the interface for the default bearer. No new bearer will
be created with this call and the settings for the bearer will come
from the default profile, irregardless of what parameters are passed
to the "start network" method.
The ofono_gprs_cid_activated attachment machinery cannot go through
ofono_gprs_status_notify for getting the attached property set because
that would result in the automatic contexts that were just set up
being released. As such, it needs to call gprs_set_attached_property
manually. Doing so, however, means that the driver_attached property
never gets set, resulting in all contexts being released when the
network transitions between registered states (roaming/non-roaming).
ofono_gprs_status_notify is an asynchronous notification that messes
with the 'attached' state of the GPRS atom. This method is normally
prevented from running while an attach is in progress because the
attachment machinery wants to finish up and make it's own determination
of attach state.
When automatic context activation is relevant, as for LTE networks,
the ofono_gprs_cid_activated machinery replaces the usual set_attach
machinery for attaching to the network. The cid_activated variant,
however, does not guard against simulatenous invocations of
ofono_gprs_status_notify. This causes a race whereby status_notify
sets the state to 'attached' before the context is fully constructed
and set to active. If the connection manager sees the 'attached'
state before there are any 'active' contexts, it may decide to
activate a context manually which is not the correct behaviour for
this type of network.
This patch makes the *_cid_activated machinery an 'attaching' state,
introducing the same guards that set_attached has to prevent
ofono_gprs_status_notify from running concurrently.
Marcel Holtmann
Slava Monich
Alexander Couzens
Vincent Cesson
Denis Kenzior
Luiz Augusto von Dentz
Jonas Bonn