This adds documentation for the following fields in
networkmonitor-api.txt
RSCP: Received Signal Code Power
ECN0: Received Energy Ratio
RSRQ: Reference Signal Received Quality
RSRP: Reference Signal Received Power
Add more ofono netmon info types that will be served through the netmon
interface. The main user of this now will be the ublox modem.
RSCP: Received Signal Code Power
ECN0: Received Energy Ratio
RSRQ: Reference Signal Received Quality
RSRP: Reference Signal Received Power
Otherwise the attached state gets to be set before the actual LTE
automatic context is ready. This triggers a race between connman
and ofono: connman sees status attached before the context is active
so connman will try to activate another context with same apn and will
fail over and over again.
The spec supports UCS2, but in reality UTF-16 is used, which supports
4-byte characters, which could be split into different message
fragments. Accumulate the entire UTF-16 message before converting to
UTF8.
Author: Martin Jones <martin.jones@jolla.com>
The U-Blox documentation specifies the following:
* get interface ip and dns from +CGDCONTRDP
* get gw ip and netmask from +UIPADDR
However, different firmware versions have different befaviour:
* On newer firmware, +UIPADDR returns error. But it's possible to configure
gateway ip == ipterface ip (read from CGDCONTRDP).
* On older firmware, we can actually use the commands specified in the
docs.
This patch runs +CGDCONTRDP, configures everything and then tries to run
+UIPADDR. In that works, reconfigures gw ip and netmask.
Adds U-Blox Toby L2 driver for setting the default APN via the
+UCGDFLT command. Currently only IPv4 is supported. APN is
not stored to modem's non-volatile memory. oFono will manage this
default APN via it's config storage.
When receiving an empty default APN, the value is reset.
This implementation can only get/set the default APN setting. But
anything expected for this atom is there:
* D-Bus interface
* sync-ing settings to/from file
* interaction with driver
Events like +CLCC and +CCWA can have contact name attached to the
end of line. If this field contains odd number of quotation marks,
parser will eventually reject such message as malformatted.
... in pri_deactivate_callback
This prevents attached state from getting stuck at 0 like this:
1. Context deactivation is initiated over D-Bus, ctx->pending is set
2. Attached becomes FALSE, context is still marked as active
3. Attached becomes TRUE, gprs_attached_update sets GPRS_FLAG_ATTACHED_UPDATE
4. Deactivation completes, attached is 0, driver_attached is 1
Futher network status updates don't call gprs_attached_update because
driver_attached is still 1, so attached is staying 0 until we lose the
data registration again which may not happen for quite a long time.
Add rilmodem test engine. This engine is an improvement on the rilmodem
test server that allows us to test generic interactions with the
rilmodem driver. Instead of just be able to check content of received/
sent bytes on the rild socket, we can now specify a set of steps for a
test that include interactions with the atom. The step types are
- TST_ACTION_SEND: The harness sends a parcel
- TST_ACTION_CALL: The harness calls a driver function
- TST_EVENT_RECEIVE: The driver sends a parcel
- TST_EVENT_CALL: The driver calls a harness (atom) function
When the modes are modified with AT^SETPORT="FF;12,1,16", this modem
and pcui will appear using different ids. Update the interfaces
identifier accordingly.
The huawei E3372 exposes two USB tty at /dev/ttyUSB0 and /dev/ttyUSB1
/dev/ttyUSB1 is properly detected as modem.
/dev/ttyUSB0 is the pcui.
lsusb shows 12d1:1506 Huawei Technologies Co., Ltd. Modem/Networkcard
strtol clamps returned value between INT_MIN and INT_MAX, causing
invalid value (255.255.255.127) being reported for any address
if last octet > 127 when sizeof(long) == 4.
Djalal Harouni
Denis Kenzior
Dragos Tatulea
Slava Monich
Kuba Pawlak
Caiwen Zhang
Marcel Holtmann
Alfonso Sánchez-Beato
Antoine Aubert
Frédéric Dalleau
Santtu Lakkala
Samrat Guha Niyogi