This driver is based on Linux 2.6.39 8139too driver.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The doxygen documentation is long outdated. Remove it. It will
be replaced with sphinx based documentation later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Even when both the ethernet controller and the phy support certain
features a board may have additional limitations. Allow specifying
it in the devicetree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add stripped sown version of the reset controller
framework from the Linux kernel.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Clock gates having the CLK_GATE_HIWORD_MASK flag set use the upper 16
bits of the register as a "write enable" mask for the value in the
lower 16 bits.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a clk_gate_flags argument to clock gate creation functions
to allow the introduction of new clock gate modifiers.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When a mtd device can have bad blocks we want to create a
bb device, so do this automatically. This allows us to
drop bb device creation from the environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Rework the current framework so that I/O mapped I/O resources are
also possible.
Signed-off-by: Michel Stam <michel@reverze.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This updates the clk-divider to Kernel code, but without power-of-two
divider support which we do not need yet. This also adds table based
divider support to the divider.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This macros are used in exported from linux TI DaVinci code.
Also this macros are used in MIPS cache support code.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MTD internal API presently uses 32-bit values to represent device
size. This patch updates them to 64-bits but leaves the external API
unchanged.
In general, changing from 32-bit to 64-bit values cause little
or no changes to the majority of the code with the following
exceptions:
- printk message formats;
- division and modulus of 64-bit values (mtd_div_by_wb,
mtd_div_by_eb may be used in some of such cases).
Was tested on phyFLEX i.MX6.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Grigory Milev <g.milev@sam-solutions.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The default nand_read_subpage implementation returns -ENOSUPP, so we have
to make sure that barebox never uses this implementation. By setting the
NAND_SUBPAGE_READ flag to 0x0 we ensure NAND_HAS_SUBPAGE_READ() never returns
true and also give the compiler a chance to optimize away some unused code.
subpage reads are a rather exotic feature even in Linux. It is only used on
largepage NANDs with soft ecc. Even if we have this case it needs non page
aligned reads to actually profit from this feature.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Hattink, Tjalling [FINT] <T.Hattink@fugro.nl>
This imports the Marvell mbus driver from Linux. The mbus is the
main downstream bus found on all Marvell Orion SoCs. The driver
deals with re-configurable address windows which are currently
parsed from DT. Also enable the driver as default on all MVEBU
SoCs. While at it, also reorder drivers/bus/{Kconfig,Makefile}
alphabetically.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This implements a of_phy_device_connect to allow DT enabled drivers
to connect to a PHY device by using the PHY's DT node only. It
currently assumes that each PHY node is a child of the corresponding
mdio bus.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Boards register a fixup for a phy without checking if phy support
is enabled. To fix compilation without phy support add a static
inline wrapper for phy_register_fixup_for_uid.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
miitool without arguments will try to show status for all phys.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ubiformat needs the subpagesize to work correctly. The kernel uses
sysfs to pass the subpagesize, but in barebox we have the possibility
to extend struct mtd_info_user. Add a corresponding field and use it
in ubiformat.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With this phy_device_connect only registers a phy device if it wasn't
registered already. This allows us to register phy devices outside
of ethernet drivers. phy_device_connect will now pick up an already
registered phy given that it's not attached to another ethernet device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If an ethernet device already has a phy in phy_device_connect all we
have to do is to start autonegotiation. Do this early and bail out
so that for the rest of the code it's clear that we have to search for
a phy device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This add barebox versions of of_clk_init for parsing and registering
clock providers from DT. Also, a macro CLK_OF_DECLARE is added, that
allows to put init callbacks into its own section that can be linked
in the binary.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A lot of files rely on include/driver.h including include/of.h (and
this including include/errno.h. include the files explicitly so we can
eventually get rid of including of.h from driver.h
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Antony Pavlov
Lucas Stach
Beniamino Galvani
Michel Stam
Dmitry Lavnikevich
Sebastian Hesselbarth