Support the setup of the mmc voltage, when booting OMAP4 with twl6030
from nand.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added i2c support for omap4. Tested on pcm049.
Driver based on linux kernel implementation.
Also added a shift to access 16-bit registers
to make support for OMAP730/850 possible.
If accessing a non existing slave the bus will go into arbitration mode.
It's unable to recover from it.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, there are multiple definitions of run_shell()
for each board that can be build in "xload" configuration.
Now there is only one function used by all boards.
The functions defined in xload.c are used only when "xload"
configuration used; but it gets compiled unconditionally.
This has been fixed as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This helper function can be used for automatic
SDDR configuration based on register settings
made by a previously first stage bootloader
i.e. x-loader.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add platform data to specify maximum frequency of hsmmc interface
which can be restricted due to external level shifters.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use generic read/write depending on the memory size
if no reg_read/write defined
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
If OMAP4 fall back to MMC1 boot in bootmode 0x39 (NAND,USB,UART,MMC1)
NAND and MMC bit in TRACING_VECTOR3 are set. With changed order it will
detect boot from MMC.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add some common xload helper functions to determine the boot source
on omap3/4 and to load images from mmc and nand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds BCH ecc support to the omap nand driver. The BCH
error correction allows for up to 8 bit error correction. It is
also needed for booting from nand on omap4.
This is based on code from Sukumar Ghorai <s-ghorai@ti.com>:
[PATCH] omap3: nand: bch ecc support added
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On omap we use different ecc modes for different purposes. The initial
boot code has to be written with hardware ecc whereas Linux usually uses
software ecc. To be able to write in both modes with a sinlge barebox
image introduce a eccmode device parameter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If compiled without gpio support the linker will throw the
gpio functions away anyway, so make the omap kconfig entries
a bit easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Give this omap specific entry an omap namespace. Also, remove
unnecessary dependency to omap2/3 in nand Kconfig.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The original plan was to add all omap devices into the boards/omap
directory. Anyway, there will be reasons to put a board somewhere
else, so move the generic parts into the omap architecture directory.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current gpio support is derived from the kernel which allows
for support for omap2/3/4 in a single kernel. We do not need this
here, so make it more simple to be able to add omap4 support later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch updates the clock dividers for the graphics
processor.
It is based on commit:
c4e1d9b718b65436e30422506f43fa4eb21069d3
at http://arago-project.org/git/projects/?p=u-boot-omap3.git
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In function get_osc_clk_speed(), the SYS_CLK divider
was being changed 'suddenly'.
This change has cascading effect on the derived clocks,
leading to inconsistent behavior - often a crash.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the basic clock initizlization for OMAP36XX.
Portion of this patch is based on commit:
29587220909e639cda4fb5a35cb5bf33aba242b9
at http://arago-project.org/git/projects/?p=x-load-omap3.git
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch defines functions that contain steps to configure
DPLL for each clock domain.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the DPLL tables for OMAP36XX and the
necessary functions to access these tables.
Both definitions follow the conventions used for
OMAP34XX.
All tables, currently, correspond to SYSCLK at 26MHz.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The PER domain dpll significantly differs from 34x.
This patch defines struct to collate related info.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support to detect the different
OMAP36XX silicon revisions.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the support to detect OMAP3630.
It also re-organizes the CPU_xxxx definitions in sys_info.h
to ascending order so that newer silicons can be added at
bottom.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds suffix 34x to DPLL tables and related functions to
indicate that they are applicable to OMAP34XX only.
The suffix was required to prepare for support of OMAP36XX in the
subsequent patch series.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch updates the DPLL functions to return correct
DPLL table based on the cpu revision.
The DPLL table for PER domain is same across all revisions,
but the function signature has been updated to maintain
consistency in the API definition.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Content from monolith implementation in prcm_init() has been
moved into separate functions - per clock domain. This makes
code easy to adapt for silicon revisions and families.
Few cosmetic changes may have been done during this movement.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds DPLL tables for OMAP34xx ES1.0 and ES2.0.
When more than one table is added, the get_xxx_dpll_param()
was updated to use the tables corresponding to ES2.0 to
ensure that current functionality doesn't break.
In addition, the tables have been reformatted for better
readability.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch ensures that all silicon revisions
are detected. (Current implementation cannot
detect ES1.0).
In the process, the 'seemingly' hardcoded macros
identifying cpu revision (e.g. CPU_ES1P1) have
been updated to include the CPU name as well.
(The mapping of IDCODE value to silicon revision
may not be same across different OMAP families).
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch sets the cpu type based on the hawkeye value
read from the IDCODE register. So far, cpu type was
hardcoded.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds macros to extract the hawkeye
and version number from IDCODE value.
Updated function get_cpu_rev() to use new macro.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Silence this warning:
arch/arm/mach-omap/arch-omap.dox:51: Warning: explicit link request to 'define' could not be resolved
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
include/common.h declares this as "unsigned long addr", so we unify it.
This also silences a doxygen warning.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Juergen Kilb
Alexander Aring
Daniel Mack
Sanjeev Premi
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Jan Weitzel
Robert Schwebel