With two eeproms that have a different compatible string (in my case
"at,24c64" and "at,24c32") dev->id is 0 for both which results in a
failure to bind the device that is probed later.
So pick a name more intelligently: If there is an alias defined in the
device tree, use this one, otherwise pick a free index.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
if devfs_create failed because "eeprom0" already exists
of_parse_partitions must not be called, otherwise the already existing
eeprom gets assigned partitions that don't belog there.
Also free dummy clients in the error path and the write protect gpio
only if it is actually valid.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also only emit the message that the device was probed when it
actually was.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The DS1307 has a square wave output pin, which can be used to output a
clock signal from the DS1307. Additionally, the DS1308 supports
configuring this pin as an input from an external clock source to
which it should sync itself.
Add support with OF device tree properties to configure these
settings. Supported features are using the clock pin as an output, an
input, the rate of the pin, and if it should be enabled on battery
backup power.
The driver does not check that the selected features are supported by
the clock chip being used. It is the designer's responsibility to
create a valid device tree node; the bootloader does not attempt to be
a device tree validator.
Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CRC32 digest can be used to check CRC32 hashes in FIT images etc.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As far as the driver is concerned, it's the same as a 1338. It's too
bad the i2c drivers can't make use of OF compatible properties with a
list of compatible devices.
Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
KSZ9081 only supports two phy ids 0x0 and 0x3. 0x0 is also
used as broadcast address. Disable broadcast, so that id 0x0
can be used as unique address on a shared bus.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit bc31d85c6e ("cdev: Add partuuid string to struct cdev") added
partuuid strings for dos partitions but only for the (up to) four
primary partitions. Do the same for the logical partitions. Their
numbers start at 5 independently of the number of available primary
partitions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
First of all the reset values of MMC interfaces are differently between
Quad and DualLite/Solo SoM.
Register VEND_SPEC2(0xC8)
Quad: 0x0
DualLite: 0x00000006
default: 0x00000006 (from i.MX6 Reference Manual)
Furthermore the ROM Code of Quad and DualLite uses the MMC interfaces
differently when it loads the bootloader from that device:
Register DLL_CTRL(0x60) Bit 25 FBCLK_SEL (0x48)
Quad: 0x0 0
DualLite: 0x01000021 1
Since the linux kernel and barebox driver doesn't reset all registers,
the MMC interface is in an inconsistent state, which leads to boot
failures for some eMMC devices on the i.MX6 DualLite SoM. The errors
look like:
mmcblk3: error -110 sending stop command, original cmd response 0x900, card status 0x400900
mmcblk3: error -84 transferring data, sector 24578, nr 2, cmd response 0x900, card status 0x0
mmcblk3: retrying using single block read
mmcblk3: error -84 transferring data, sector 24578, nr 2, cmd response 0x900, card status 0x0
blk_update_request: I/O error, dev mmcblk3, sector 24578
It's sufficient to reset register DLL_CTRL and bit FBCLK_SEL. Register
VEND_SPEC2 has no effect.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some network devices, especially when connected to a switch, are
connected via a fixed link. This patch adds support for a fixed phy
configured through device tree.
TODO: Add support for the "speed" and "full-duplex" properties.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Wjatscheslaw Stoljarski <wjatscheslaw.stoljarski@kiwigrid.com>
For the phyCORE-i.MX6 add an automount command for the first partition
on the eMMC device.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The bootm code now can handle the adding of the root= option itself,
so drop the code and let bootm do it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
It becomes a common case that the Kernel is loaded from the filesystem
which later becomes the rootfs. This adds a possibility to let bootm
automatically append the root= option to the kernel command line. This
is done when global.bootm.appendroot is true.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The settings in GPR8 are dependent upon the particular layout of the
hardware platform. As such, they should be configurable via the device
tree.
Look up PHY Tx driver settings from the device tree. Fall back to the
original hard-coded values if they are not specified in the device tree.
[Andrey Smirnov: port to Barebox codebase]
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove the remnants of the workaround for erratum ERR005184 which was never
completely implemented. The checks alone don't carry any value as we don't
act properly on the result.
A workaround should be added to the lane speed change in establish_link
later.
[Andrey Smirnov: port to Barebox codebase]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the PHY reset into a common error path of
imx6_pcie_establish_link(), deduplicating some of the debug prints. Also
reduce the severity of the "no-link" message in the one place where it is
expected to be hit when no peripheral is attached.
[Andrey Smirnov: port to Barebox codebase]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable NOR for phyCORE-i.MX6 DualLite and Quad eMMC variants.
Furthermore add an extra 'status = "disabled"' in the flash node. It
has no functional effect, because the SPI bus node 'ecspi1' is disabled,
too.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some phyCORE-i.MX6 variants have eMMC instead of a NAND chip. Provide an
update_handler for them.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The extra environment folder for the phyCORE-i.MX6 had the suffix
'-mira'. That's the name of a baseboard. Since the bootloader is generic
for all baseboards, use a generic suffix for the environment folder.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Update RAM calibration values in the flashheader file for phyCORE-i.MX6
DualLite/Solo. These are verified and tested in the climatic chamber for
commercial, extended commercial, industrial and automotive i.MX6
variants.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The phyCORE-i.MX6 has either a NAND or EMMC storage device and an
external SD-Card interface. The automatic bootsource detection in the
barebox environment should reflect that.
- If the board was booted from the external SD-Card interface, it should
continue loading the kernel and device tree from it.
- If the board was booted from EMMC, it should load kernel and device
tree from the boot partition on the EMMC.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing MMC barebox environment partitions for the phyCORE-i.MX6
with EMMC. Otherwise the barebox cannot find the environment, when the
board is boot from sd-card.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use a longer reset time for ethernet phy Micrel KSZ9031RNX. Otherwise a
small percentage of modules have 'transmission timeouts' errors like
barebox@Phytec phyFLEX-i.MX6 Quad Carrier-Board:/ ifup eth0
warning: No MAC address set. Using random address 7e:94:4d:02:f8:f3
eth0: 1000Mbps full duplex link detected
eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
T eth0: transmission timeout
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Due to hardware issues the usdhc3 interface on phyBOARD-ALCOR i.MX6 and
phyBOARD-SUBRA i.MX6 doesn't work reliable at 50Mhz. You get
communication errors like
barebox@Phytec phyBOARD SUBRA:/ ls /mnt/mmc/
mmc2: detected SD card version 2.0
mmc2: registered mmc2
imx-esdhc 2198000.usdhc: timeout 2
mmc2: Cannot read MBR/partition table
Therefore reduce the maximum clock speed to avoid these problems.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyBOARD-SUBRA-i.MX6 with phyFLEX-i.MX6 Quad 1GiB on one
bank. This patch factors out the common device tree nodes for the Quad
and Solo variant into 'imx6qdl-phytec-phyboard-subra.dtsi'.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Enable the mmc_extcsd command to read and write MMC/eMMC registers.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We have at least two places which convert a string to a boolean type,
so create a common function for this. strtobool treats
- any positive (nonzero) number as true
- "0" as false
- "true" (case insensitive) as true
- "false" (case insensitive) as false
Every other value results in an error and the input *val is not
modified. The caller is expected to initialize *val with the correct
default before calling strtobool.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
nvvar support not only needs globalvar, but also persistent
environment storage. Add a separate default-y option which
depends on ENV_HANDLING for this case. Make the option visible
to let the user decide whether he wants to have this option
and add a help text to make this decision easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ENV_HANDLING is usable even without explicit loadenv/saveenv command
support. Instead of selecting this option from loadenv/saveenv, make
this option visible. loadenv/saveenv can then depend on ENV_HANDLING
rather than selecting it. This reduces Kconfig dependencies hassles.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently global environment variables are only enabled when the
"global" command is enabled. In fact, they could be used even with
the "global" command disabled, so make the GLOBALVAR option visible.
While at it, add a help text for this option.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Implement simple adapter function to serve as a hook for 'devinfo'
command.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Uwe Kleine-König
Trent Piepho
Yegor Yefremov
Sascha Hauer
Teresa Remmet
Stefan Christ
Andrey Smirnov
Christian Hemp
Jan Remmet