Switch to new environment and add the bootscripts needed for mmc. Also,
update defconfig for new environment.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On some SoCs (for example AM35xx), the ROM bootloader passes useful
information in r0 when jumping to barebox.
To avoid overwriting this in the generic reset code, we introduce
common_reset as a C function and as an assembler macro. This is then
called form the reset entry point (either in common or in board code).
This patch is based on code by Sascha Hauer <s.hauer@pengutronix.de>.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Change clock init to allow early gpio access. Add support for 4460 clocks.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
based on: [U-Boot] [PATCH v 4/5] omap4: support TPS programming
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: F. Gasnier fabrice.gasnier@cenosys.com
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With pbl support enabled most boards need a pbl-y for their lowlevel
stuff.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Register GPIO7 as heartbeat LED, same as in the linux kernel.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add i2c-omap and twlcore driver to panda board.
(Based on similar patch for pcm049).
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If barebox is not used as the MLO, then it crashes during boot
with the below error message:
Board: Texas Instrument's Panda
PandaBoard Revision: 003
omap-hsmmc@mci0: registered as mci0
unable to handle paging request at address 0x4a064010
pc : [<8f01e820>] lr : [<8f0049a0>]
sp : 8cffff80 ip : 00000016 fp : 00100103
r10: 00000000 r9 : 00000ae7 r8 : 4030b76c
r7 : 40300200 r6 : e28f8028 r5 : 0000003e r4 : 00000000
r3 : 4a064000 r2 : 00000014 r1 : 00000001 r0 : 00000001
Flags: nzCv IRQs off FIQs off Mode SVC_32
[<8f01e820>] (panda_devices_init+0x17c/0x1e0) from [<8f006300>] (start_barebox+0x18/0x10c)
[<8f006300>] (start_barebox+0x18/0x10c) from [<8200006c>] (0x8200006c)
[<8f021248>] (unwind_backtrace+0x0/0x98) from [<8f011a00>] (panic+0x28/0x3c)
[<8f011a00>] (panic+0x28/0x3c) from [<8f02171c>] (do_exception+0x10/0x14)
[<8f02171c>] (do_exception+0x10/0x14) from [<8f021784>] (do_data_abort+0x2c/0x38)
[<8f021784>] (do_data_abort+0x2c/0x38) from [<8f021470>] (data_abort+0x50/0x60)
This is because the USBHOST module is not enabled. The module enable
is is normally done in mach-omap/xload.c which never gets called.
Since we're configuring the USBHOST CLKCTRL register in the board file
anyway, we might as well explicitly enable the module in the same place.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can use it for dhcp request too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have a bootm command which boots everything we can
simplify the defaultenvironment. We can call bootm on every
image type and can remove the kernelimage_type variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, there are multiple definitions of run_shell()
for each board that can be build in "xload" configuration.
Now there is only one function used by all boards.
The functions defined in xload.c are used only when "xload"
configuration used; but it gets compiled unconditionally.
This has been fixed as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To allow for some generic io accessors introduce io.h and use
this instead of asm/io.h throughout the tree.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit c71a77ab8 (ns16550: switch to resource) has introduced generic
read/write access to 16550 register and a 'shift' parameter to allign
register index to physicall registers.
The correct 'shift' value was missing in all omap based boards.
Corrected this to 2 which has fixed the problem.
Tested on a PCM-049 phyCORE-OMAP4 board.
Signed-off-by: Juergen Kilb <J.Kilb@phytec.de>
Tested-by: Jan Weitzel <J.Weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The new MMU setup will need SDRAM base addresses and sizes.
For this reason convert the MMU enabled ARM boards:
- move mem setup to mem_initcall. This is early but
still makes sure that we already have the console available
- move MMU setup in this initcall temporary as after the mmu_init will generic
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
use generic read/write depending on the memory size
if no reg_read/write defined
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
pass the hccr and hcor register base via resource
instroduce add_generic_usb_echi_device with hccr = base + 0x100 and
hcor = base + 0x140
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add a helper function for boards to register their memory
devices. This makes the board code smaller and also helps
getting rid of map_base and struct memory_platform_data.
And switch all of the memory to it
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
we keep struct memory_platform_data for now on we will switch off the memories
resources to struct resource
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>