Since the info is device specific and not driver specific, attach
the callback to the device. This makes it possible to have a info
callback for a device which does not have a driver attached.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If a device does not have bad blocks loop over the eraseblocks
in the driver instead of the core. This allows the mtd_dataflash
driver to erase blocks instead of pages to gain more speed during
erasing. Also the mtd_dataflash driver modifies the erase_info
struct which causes the outer loop in the core to never end.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this fix the problems introduced when detecting non ONFI flashes in
commit 4c2bdc8728
"nand_base: detect more ONFI flash"
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
actually ops.ooboffs is not defaulted so when its value gets
added to chip->oob_poi in nand_fill_oob or nand_transfer_oob
the respective memcpy is using a wrong address.
With this patch, both md -s /dev/nandraw0 and cp xyz /dev/nandraw0.sb
are working fine on an i.MX28 target (instead of crashing the board).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
if the flash has a known type, the ONFI detection won't occur
and thus we may not detect the right parameters.
By testing both namd and pagesize, as done in the kernel, we
can detect ONFI flash with know IDs.
As an example on an i.MX53 board :
- without the patch :
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xd3
(Micron NAND 1GiB 3,3V 8-bit), page size: 4096, OOB size: 128
- with the patch :
ONFI flash detected ... ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xd3
(Micron MT29F8G08ABACAWP), page size: 4096, OOB size: 224
in the first case the OOB size is wrong.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With 2k NAND flashes the data layout in memory is not what is
written on the flash device. This leads to the result that the
factory provided bad block markers are not recognized correctly.
To preserve the factory bad block information the i.MX NAND driver
will not scan for the bad blocks itself when there is no flash based
bbt available, because the mtd layer would do so based on wrong
information. Instead, a new command is introduced which allows to
manually create a flash bbt based on the correct information.
As this command is tightly coupled to mtd and the i.MX NAND driver
the command is placed under drivers/mtd/nand/ instead of commands/
where a command normally belongs to.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The information which kind of bbt (if any) is used is hidden somewhere
in the NAND layer. Expose it to a device parameter to make it detectable
and visible during runtime.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes following warning:
drivers/mtd/nand/nand_write.c: In function 'nand_do_write_ops':
drivers/mtd/nand/nand_write.c:272: warning: 'ret' may be used uninitialized in this function
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
While erasing bad blocks is a potentially dangerous operation
it is sometimes needed during development or when some foreign
code has touched the flash.
This patch adds a device parameter 'erasebad' to allow erasing
bad blocks. Since this is not wanted during production this is
behind a Kconfig option.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have some NAND specific stuff during registration,
like for example adding NAND specific device parameters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since recently we check for the page being written for not being
empty and do not actually write it when it is. This fails for a
freshly created flash bad block table when all blocks are good.
In this case the bbt code will try to write an empty page, but
with the BBT marker in OOB. This page never gets written, so the
BBT code will not find a bad block table during next start up and
writes it again. Fix this by checking if we want to write OOB data,
if we do, then write the page, even if the data is empty.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not write pages which only contain 0xff. UBI expects pages which
seem empty to be writable. This got lost with:
| commit 3139c3e9a6
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date: Thu Nov 29 11:16:40 2012 +0100
|
| mtd core: call driver write function with complete buffer
|
| mtd->write is supposed to loop around pages internally, no need
| to do this in mtd_write. This fixes a huge write performance drop
| with the m25p80 driver when it was converted to a mtd driver recently.
| Since mtd->writesize is 1 for this driver mtd_write ended up doing
| single byte writes on the flash.
Introduce mtd_all_ff as a global function since UBI currently has its own
implementation.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CFI Flash is currently handled outside the mtd layer which makes it
a special case. Integrate it into mtd so that we get rid of this
special status.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of dereferencing struct mtd_info members directly use
the wrapper functions which have an additional check if the
callback exists if it is optional, like mark_bad or is_bad.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Kernel has mtd_read, mtd_write, mtd_erase and mtd_block_markbad.
Add these functions to barebox aswell to make future mtd synchronizations
with the kernel easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These are currently named mtd_read/write/erase. Functions with
the same name exist as global functions in the kernel. Rename
them to mtd_op_* to avoid name clashes with future mtd updates.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Previously, during a multi-page write, chip->oob_poi would not be
reinitialized.
See commit f722013ee9fd24623df31dec9a91a6d02c3e2f2f in the kernel
for an analogous change.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Oleksij Rempel
Oleksij Rempel
Eric Bénard
Alexander Shiyan
Jan Luebbe