The timeout for wating for the bus to be idle is too short when the
card does internal garbage collection. This was triggered with filling
an SD card under Linux with /dev/urandom, then doing a saveenv under
barebox afterwards.
Linux has timeouts here up to 300ms. Use a second to be safe.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
toread is unitialized. We have to use count instead.
| commit 992c291e95
| Author: Sascha Hauer <s.hauer@pengutronix.de>
| Date: Sat Sep 15 16:54:47 2012 +0200
|
| mtd mtdraw: Fix partial page read
|
| When reading parts of a page we have to limit the maximum bytes copied
| to the remaining bytes of a page.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will ensure the data are set to 0 (list as example)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When reading parts of a page we have to limit the maximum bytes copied
to the remaining bytes of a page.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
since 99e72c8bbd on an i.MX51 based board,
I get : "phy0: Link is up - 1000/Full". It seems miidev tries to probe
the PHY to early and gets 0x3ffff which leads to the wrong capabilities
setting.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If pdata is NULL smc911x_probe will crash. Checking the zero initialized
priv->shift results in default configuration if pdata is not set.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the check need to be inverted
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For the size_t type the format specifier %zu or %zx must be used.
See Documentation/printk-formats.txt in the kernel for details.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The stmpe mfds can be connected via i2c and spi. This driver provides the basic
infrastructure for the i2c kind. It can be added as a normal i2c-device in the
board code. To enable functions a platform_data struct has to be provided, that
describes what parts of the chip are to be used.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A function to calculate the frequency divider and digital filter sampling rate
for the 85xx processors is added to the i2c-imx driver. Hence, this driver is
usable on IMX and 85xx machines.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The IMX i2c driver is to be used by SOCs on both the ARM and PPC architetures.
Use a more neutral name for the structure, function names and #define.
The driver name is now "i2c-fsl".
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A string allocated by asprintf is not freed, so change it to a sprintf
with the preallocated buffer.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Board support units must use only the provided functions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mtdoob and mtdraw device don't clean up correctly.
Added a private data element to hold allocated memory.
Fix remove of mtdoob and mtdraw device.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
poll the READY bit in PMT_CTRL. Any other access to the device is
forbidden while this bit isn't set. Try for 100ms
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use linux kernel chip detection from 3.5
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
detect if the bus is swapped and report a 32bit drivers is used on a 16bit bus
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
switch ipe337: to it at the same time to do not brake it
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to replace them depending on the platform data.
So we can specify shift and reg io witdh (16bit/32bit)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this make the driver more readable
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
miidev_wait_aneg() polled the wrong bit, so link detection did fail on
boards where the PHY had to come out of a powerdown mode.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In usb_hub_configure the hub is asked for its descriptor and among other things
its bPwrOn2PwrGood time. In the actual hub_power_on function this information
was not used and a hardcoded value was used instead. For some hubs this delay
is to short. So, use the delay the hub wants.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
else when we do "erase /dev/m25p0.rootfs; reset", the board
will never reboot as the flash is busy to finish the erase
command.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested with a m25p128 flash both in nand boot & spi boot.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With pbl support enabled most boards need a pbl-y for their lowlevel
stuff.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The existing nand_boot functions all do the same, so move it to
a common place. To be flexible enough for future boards the real
image size is used instead of hardcoded 256k.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <jbe@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This update adds the GIANFAR driver along with the configuration
and build files.
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces a new NAND_BUSWIDTH_AUTO flag which can be used
to automatically detect the nand buswidth. The id is always read
in 8bit mode. An additional callback is needed to switch the nand
controller into 16bit mode.
This currently depends on a safe read_byte (always) and read_buf
(for onfi-only flashes) callback. It has been tested on OMAP, but
is not something that generally works. For this reason the existence
of the set_buswidth callback is used to determine whether we are
able to do autodetection or not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Eric Bénard
Jan Weitzel
Jan Luebbe
Steffen Trumtrar
Renaud Barbier
Alexander Shiyan
Alexander Aring
Wolfram Sang
Wjatscheslaw Stoljarski