This driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
Based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we print the correct size
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will be use by at24 driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This returns an I2C client bound to the "dummy" driver, intended for use
with devices that consume multiple addresses. Examples of such chips
include various EEPROMS (like 24c04 and 24c08 models).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is need for sequential read/write.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is needed for i2c-gpio support
Based on linux 3.7-rc2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can show the this of i2c busses
set the bus device as parent of all devices.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use irq pin as the pin is asserted untill we clear it
This will allow to do not poll on i2c which slow down barebox
If no irq_pin is provided fall back on i2c polling
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
fec_init() initializes some bits important for phy access, so do
this before the mdiobus is registered. This fixes mdiobus support
on i.MX28 boards in RMII mode.
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several i.MX boards (all i.MX6 boards) need to do some adjustments
to phy registers. If barebox itself does not use network, networking
won't work in the kernel if the kernel does not have the fixups. Connect
the phy at probe time so that these tweaks are done during probe so that
the kernel works without phy register tweaks. Also this has the effect
that the phy device is present and introspectable without doing fake
network transfers beforehand.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The console layer calls of_device_is_stdout_path for a new console. When
we are booting without devicetree then of_chosen is NULL which makes barebox
crash. Check for a NULL pointer in of_find_property to prevent this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on linux implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on linux implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on linux implementation.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
export for each device via param
the familly id (fid)
the id
the full reg_num
so for simple 64bit memory rom(ds2401/ds2411/ds1990*) no need driver.
Based on linux implementation, cleaned and re-implement the master/slave
support to use the device/driver model correctly.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
common.h should come first, other include files implicitely depend
on it. Also, remove unused fs.h and remove commented line.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Got this when compiling sandbox on a 64-bit system:
drivers/mtd/ubi/cdev.c: In function ‘ubi_volume_cdev_read’:
drivers/mtd/ubi/cdev.c:26:2: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The check is wrong since it would have to check whether the
new iomem region overlaps with an existing region. Checking
for the base address only is not enough.
Currently this is not possible because every device conflicts
with the top iomem region which covers the whole address space.
This at least fixes the regression that devices whose memory region
begins at 0x0 can no longer be succesfully registered.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The _send function should not return the length
of the transmitted packet.
See also
commit 76c4c9e48f
Author: Jan Luebbe <jlu@pengutronix.de>
Date: Fri Sep 28 18:17:44 2012 +0200
davinci_emac: return 0 on successful transmit
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_update_linkspeed':
/opt/work/barebox/drivers/net/designware.c:234:9: error: 'mac_p' undeclared (first use in this function)
/opt/work/barebox/drivers/net/designware.c:234:9: note: each undeclared identifier is reported only once for each function it appears in
/opt/work/barebox/drivers/net/designware.c: In function 'dwc_ether_open':
/opt/work/barebox/drivers/net/designware.c:254:6: error: too few arguments to function 'phy_device_connect'
/opt/work/barebox/include/linux/phy.h:252:5: note: declared here
/opt/work/barebox/drivers/net/designware.c: At top level:
/opt/work/barebox/drivers/net/designware.c:226:13: warning: 'dwc_update_linkspeed' defined but not used
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can check it with the kernel one
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old clock support is now unused. Remove it. The former i.MX clko
command is superseeded by generic clock manipulation commands.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Wolfram Sang
Alexander Aring
Antony Pavlov