This patch adds the crc32 command to be build
as host and optionally as target tool.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Image payload size should always be a multiple of 4 bytes. This fixes
mis-sized image payload by allocating payload buffer as multiple of 4
but load true filesize into the payload buffer.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Xmodem blocks should start with SOH but kwboot never sets the first
block byte. This fixes kwboot's Xmodem block initialization and sets
first block byte to SOH.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The documentation says setupmbr should be used with the image named
'barebox', but it should instead be done with the 'barebox.bin'
image. Attempting to use setupmbr on the ELF barebox image simply
fails:
$ ./scripts/setupmbr/setupmbr -s 32 -m ./barebox -d disk.img
No MBR signature found
barebox image seems not valid: Bad MBR signature
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
"%i" in format string requires a signed integer.
"%d" in format string requires a signed integer.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In some cases kernel-install can fail without printing anything. Add
error messages for these cases.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds a tool for installing kernels according to the bootloader
spec. systemd already has a similar tool, but it is limited to installing
kernels on the currently running system. The barebox kernel-install
tool instead can also be used to install kernels on removable media on a
development host for cross development. It is compiled in two variants,
as 'kernel-install' for the host and as 'kernel-install-target' using
$CROSS_COMPILE.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
using obj-y for targetprogs only works until only a single program
is compiled. Adding the second one will end up in the linker trying
to link both together.
Add targetprogs-y to fix this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Altera SoCFPGAs expect a simple header for their first stage
loaders. This adds a tool to generate images for the SoCFPGAs. The
header is either embedded into the image or optionally prepended
to the image. In this case code is added to jump over the image
header.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to write the size of barebox at an offset of the binary
this is needed for ARM when using relocated binary
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Several boot modes on i.MX can't cope with partial pages or
non word aligned image lengths, so align the size to 4k.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When we want to pass the imxcfg files through cpp we also want to
allow defines which define multiple commands. For this to work we
have to use an additional command delimiter as we can't pass '\n'
though cpp. Use ';' for this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
kbuild: create directory for dir/file.o
When add a obj with dir to obj-y, like this
obj-y += dir/file.o
The $(obj)/dir not created, this patch fix this.
When try to add a file(which in a subdir) to my board's obj-y, the build
progress crashed.
For example, I use at91rm9200ek board, and in kernel dir run:
mkdir objtree
make O=objtree at91rm9200_defconfig
mkdir arch/arm/mach-at91/dir
touch arch/arm/mach-at91/dir/file.c
and edit arch/arm/mach-at91/dir/file.c to add some code.
then edit arch/arm/mach-at91/Makefile, change the following line:
obj-$(CONFIG_MACH_AT91RM9200EK) += board-rm9200ek.o
to:
obj-$(CONFIG_MACH_AT91RM9200EK) += board-rm9200ek.o dir/file.o
Now build it:
make O=objtree
Then the error appears:
...
CC arch/arm/mach-at91/board-rm9200dk.o
CC arch/arm/mach-at91/board-rm9200ek.o
CC arch/arm/mach-at91/dir/file.o
linux-2.6/arch/arm/mach-at91/dir/file.c:5:
fatal error: opening dependency file
arch/arm/mach-at91/dir/.file.o.d: No such file or directory
Check the objtree:
LANG=en ls objtree/arch/arm/mach-at91/dir
ls: cannot access objtree/arch/arm/mach-at91/dir: No such file or directory
It's apparently that the target dir not created for file.o
Check kbuild source code. It seems that kbuild create dirs for that in
$(obj-dirs). But if the dir need not to create a built-in.o, It should
never in $(obj-dirs).
So I make this patch to make sure It in $(obj-dirs)
Signed-off-by: 张忠山 <zzs213@126.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for extracting LZ4-compressed kernel images,
as well as LZ4-compressed ramdisk images in the kernel boot process.
This depends on the patch below
decompressor: Add LZ4 decompressor module
Signed-off-by: Kyungsik Lee <kyungsik.lee@lge.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The compiled in dcd images generate an intermediate assembly file. Instead
of generating them as *.S generate them as *.dcd.S to better identify them
as generated files. These are then added to .gitignore.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds host tools for i.MX to generate the i.MX internal
flash header format and a tool to upload these images to an
i.MX SoC via USB.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We had pbl_cc__o_c instead of pbl_cc_o_c. This caused all pbl object
files to be rebuilt everytime due to missing .cmd file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Based on the same Linux commit from Stephen Warren:
commit b40b25fff8205dd18124d8fc87b2c9c57f269b5f
Author: Stephen Warren <swarren@nvidia.com>
Date: Wed Mar 6 10:58:37 2013 -0700
kbuild: always run gcc -E on *.dts, remove cmd_dtc_cpp
Replace cmd_dtc with cmd_dtc_cpp, and delete the latter.
Previously, a special file extension (.dtsp) was required to trigger
the C pre-processor to run on device tree files. This was ugly. Now that
previous changes have enhanced cmd_dtc_cpp to collect dependency
information from both gcc -E and dtc, we can transparently run the pre-
processor on all device tree files, irrespective of whether they
use /include/ or #include syntax to include *.dtsi.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This brings us the following which we need for dtb file generation.
commit 2ab8a99661f4ce052bbad064237c441371df8751
Author: Stephen Warren <swarren@nvidia.com>
Date: Wed Mar 6 10:27:45 2013 -0700
kbuild: fixdep: support concatenated dep files
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The v0 header, used on Kirkwood, has some fields to indicate the type
of the NAND ECC, and the page size of the NAND. This commit adds
support for such fields, which are needed to support the Kirkwood
Guruplug platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Alexander Aring
Sascha Hauer
Michael Grzeschik
Sebastian Hesselbarth
Alexander Shiyan
Thomas Petazzoni
Jean-Christophe PLAGNIOL-VILLARD
Darren Garnier
张忠山
Kyungsik Lee