The FSF address has changed in the past. Instead of updating it
each time the address changes, just drop it completely treewide.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Here is a test output:
barebox 2012.07.0-00136-ge3ab4bc-dirty #23 Tue Jul 3 23:10:44 MSK 2012
Board: Phytec phyCORE-i.MX27
mc13xxx-spi@mc13xxx-spi0: Found MC13783 ID: 0x00009b [Rev: 3.1]
cfi_flash@cfi_flash0: found cfi flash at c0000000, size 33554432
NAND device: Manufacturer ID: 0x20, Chip ID: 0x36 (ST Micro NAND 64MiB 1,8V 8-bit)
Bad block table found at page 131040, version 0x01
Bad block table found at page 131008, version 0x01
imxfb@imxfb0: i.MX Framebuffer driver
cfi_protect: protect 0xc0080000 (size 1048576)
Using environment in NOR Flash
Found NXP ISP150x ULPI transceiver (0x04cc:0x1504).
ehci@ehci0: USB EHCI 1.00
imx-mmc@mci0: registered as mci0
Malloc space: 0xa6f00000 -> 0xa7efffff (size 16 MB)
Stack space : 0xa6ef8000 -> 0xa6f00000 (size 32 kB)
running /env/bin/init...
Hit m for menu or any other key to stop autoboot: 3
type exit to get to the menu
barebox@Phytec phyCORE-i.MX27:/ mci0.probe=1
mci@mci0: registered disk0
barebox@Phytec phyCORE-i.MX27:/ devinfo mci0
resources:
driver: mci
Card:
Attached is an SD Card (Version: 1.10)
Capacity: 1962 MiB
CID: 1C535653-44432020-1000013C-7E007200
CSD: 005E0032-5F5A83D5-2DB7FFBF-96800000
Max. transfer speed: 25000000 Hz
Manufacturer ID: 1C
OEM/Application ID: 5356
Product name: 'SDC '
Product revision: 1.0
Serial no: 81022
Manufacturing date: 2.2007
Parameters:
probe = 1
barebox@Phytec phyCORE-i.MX27:/ mkdir /d
barebox@Phytec phyCORE-i.MX27:/ mount /dev/disk0.0 fat /d
barebox@Phytec phyCORE-i.MX27:/ ls /d
barebox.bin
barebox@Phytec phyCORE-i.MX27:/
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Storing the size instead of the resource end in struct resource was
a mistake. 'size' ranges from 0 to UINT[32|64]_MAX + 1 which obviously
leads to problems. 'end' on the other hand will never exceed
UINT[32|64]_MAX. Also this way we can express a iomem region covering
the whole address space.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added support for CompactFlash cards for PCM970 development board via
PCMCIA window.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Actually ISP1504 ULPI chip are installed on PCM970 development board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some devices need to be moved to the PCM970 source file later, because
in fact these devices are not installed on the main unit PCM038.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Alexander Shiyan