Pass the config file to cmd_imx_image as arguments to make it more
flexible. Also add the possibility for another arg containing additional
options.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The imx-image tool can now generate signed images itself, so we can
switch to this mechanism:
- Move the CSF templates to header files which can be included by the
flash config files
- remove images/Makefile.imxhabv4 which is no longer necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently only second stage booting from the vendor U-Boot is tested. I
don't want to flash barebox into NAND yet because UART-booting for
recovery doesn't work for me.
Working so far are:
- UART
- networking
- nand flash
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also move the initcall to the level matching the name of the
function.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyFLEX-i.MX6 DualLite 1GiB on one bank with NOR.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyFLEX-i.MX6 Solo with 128MB and 256MB RAM on one
memory bank.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for phyFLEX-i.MX6 Quad 512MiB RAM on one bank.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In the current naming schema the phyFLEX-i.MX6 variants which only use
one bank for memory have the suffix "1bank". The variants which use two
banks of memory have no suffix.
The patch fixes the name of the phyFLEX-i.MX6 Solo variant with 512MiB
on one bank. So the name of the image file changes from
barebox-phytec-pbab01s-512mb.img
barebox-phytec-phyboard-subra-512mb.img
to
barebox-phytec-pbab01s-512mb-1bank.img
barebox-phytec-phyboard-subra-512mb-1bank.img
This patch touches the phyFLEX-i.MX6 Kit variant and the
phyBOARD-SUBRA-i.MX6 which shares the same phyFLEX-i.MX6 module.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The main idea behind this patch is to avoid redundant code. Because of
the module similarities of all i.MX6 based phytec boards, we can merge
its code.
The phytec-som-imx6 merges the code of all i.MX6 based phytec SOMs. So
we will have only one "board" in the barebox for phyCARD-i.MX6 and
phyFLEX-i.MX6.
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Now that we have a full set of DRAM configuration entries we can
build images for the full set of modules on Hummingboard.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a complete set of DRAM configuration values for all of the
MicroSOM variants extracted from SolidRun U-Boot.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To reflect that the current image is in fact for a combination of a
MicroSOM i1 with a Hummingboard baseboard.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Use name similar to other boards thus remove freescale from image
name since this is not a Freescale board, move SoC type after
company name.
So image name changed from barebox-freescale-imx6q-embedsky-e9.img to
barebox-embedsky-imx6q-e9.img
Signed-off-by: Anton Bondarenko <anton.bondarenko.sama@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Create a new file named 'barebox-flash-images' in the top level output
directory that lists each image generated, one per line. Paths will
be relative to the top level output directory. This works if multiple
images are generated as well as for a single image.
Also update the existing barebox-flash-image symlink to point to the
image in all cases where there is a single image generated. If
multiple images are generated, it will point to the non-existent file
'multi-image-build'.
Signed-off-by: Trent Piepho <tpiepho@kymetacorp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support support for the i.MX6 Technexion Wandboard. The
board comes in different SoC variants and different amounts of RAM.
The baord type is autodetected based on the SoC type, so all boards
can be supported by the same binary image.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
pblx-y must be passed the entry point function without any extension.
Otherwise the pblb file is not added to $targets and is removed by
make as an intermediate file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The cm-fx6 board is a module from Compulab with different i.MX6 SoCs.
This module is also found in the Utilite Mini Computer this patch
also adds support for.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for all possible combinations of phyFLEX-AM335x modules.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for all possible combinations of phyCORE-AM335x
modules.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added support for IM8G16D3FBBG15EI 1024MiB RAM on one chip.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Some boards like to do their SDRAM setup in code rather than in hardcoded
DCD tables. For these boards the bootloader has to be loaded to the internal
SRAM which is often too small for a full featured barebox. This new SRAM
image type target allows to overcome this limitation. The image created
with the new imx-sram-img rule is a regular imx-image with the difference
that the load size only spans the pblx image and not the whole image including
the payload. The pbl image easily fits into SRAM. The strategy is that this
initial code initializes the SDRAM, loads the whole image to SDRAM and jumps
to it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This enabled multi image support for the Garz&Fricke Vincell board. Also
it adds the Vincell-LT as a second image with a separate device tree.
Previously we used the same image on both the Vincell and the Vincell-LT
image since the differences are not that significant for barebox. Still
this was good for quite some confusion internally, so let's properly
introduce a second image.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Breathe some life back into the beagleboard:
- switch to multiimage support
- update config
- initialize early UART for debugging
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit add a very basic code to allow Barebox to be booted from
IRAM. Given that the amount of IRAM on most i.MX variants is
insufficient to contain a copy of Barebox with any reasonable degree
of functionality this code uses IRAM only as a temporary location and
eventually bootstraps from DRAM. But the presense of the intermediate
IRAM-only stage allows to add provisions to test the area of DRAM that
Barebox would be using to facilitate various testing scenarious.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for Marvell Armada XP based 4-bay NAS Lenovo
Iomega ix4-300d.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Before adding new Armada XP based boards becomes messier than necessary,
sort Armada XP based board Kconfig and image Makefile alphabetically.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds high assurance boot support (HABv4) image generation to
barebox, currently tested on i.MX6 only.
In order to build a signed barebox image, add a new image target to
images/Makefile.imx as illustrated in the diff below:
- - - a/images/Makefile.imx
+ + + b/images/Makefile.imx
@@ -163,10 +163,14 @@ image-$(CONFIG_MACH_SABRELITE) += barebox-freescale-imx6dl-sabrelite.img
pblx-$(CONFIG_MACH_SABRESD) += start_imx6q_sabresd
CFG_start_imx6q_sabresd.pblx.imximg = $(board)/freescale-mx6-sabresd/flash-header-mx6-sabresd.imxcfg
FILE_barebox-freescale-imx6q-sabresd.img = start_imx6q_sabresd.pblx.imximg
image-$(CONFIG_MACH_SABRESD) += barebox-freescale-imx6q-sabresd.img
+CSF_start_imx6q_sabresd.pblx.imximg = $(havb4_imx6csf)
+FILE_barebox-freescale-imx6q-sabresd-signed.img = start_imx6q_sabresd.pblx.imximg.signed
+image-$(CONFIG_MACH_SABRESD) += barebox-freescale-imx6q-sabresd-signed.img
+
Here the default i.MX6 CSF file $(havb4_imx6csf) is used, it's generated during
build on from the template "scripts/habv4/habv4-imx6.csf.in". You can configure
the paths to the SRK table and certificates via: System Type -> i.MX specific
settings -> HABv4 support.
The proprietary tool "cst" by Freescale tool is expected in the PATH.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds support for the i.MX6 based Eltec HiPerCam board.
This board comes with different i.MX6 flavours and different
memory sizes. Currently supported is the i.MX6dl version with
256MB DDR3 RAM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The BCTs are build objects and as such are located in the objtree instead of
the srctree. Fix out-of-tree build by defining a variable which refers to the
board directories in the objtree and use it for Tegra.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A lot of the image makefiles define an equal board variable, which
gives the impression that this variable is unique for this makefile.
As those files aren't freestanding makefiles but get included into a
parent makefile this is not actually true. Attempts to override this
variable will not work reliable as make is picking up a random instance.
Fix this confusion by moving this variable out of the individual makefiles.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The main idea behind this patch is to avoid redundant board code.
Because of the module similarities of all am335x based phytec boards, we can
merge its code.
The phytec-som-am335x merges the code of all am335x based phytec SOMs.
So we will have only one "board" in the barebox for phyCORE, phyFLEX.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
