in commit 2bdc9f57a8 the iomux was synced
with the kernel but this leads to some changes in the PAD_CTRL of some
FEC pins leading to a non working FEC on our cpuimx51 board.
This patch set back the PAD_CTRL of the missing pins to the initial
value.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The IMX i2c driver is to be used by SOCs on both the ARM and PPC architetures.
Use a more neutral name for the structure, function names and #define.
The driver name is now "i2c-fsl".
Signed-off-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a function to take the usbphy1 through its initialization procedure.
The imx6_usb_phy1_disable_oc function is needed at least on the sabrelite,
as the power design is faulty. The state on other imx6 boards is unknown,
therefore it is an extra function call at the moment.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
tested with a m25p128 flash both in nand boot & spi boot.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With pbl support enabled most boards need a pbl-y for their lowlevel
stuff.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The i.MX5 does not have a valid function to get the spi clock. This
patch introduces a function for i.MX6, and moves the bogus spi clock
speed to the speed-imx5*.c. Not nice, but preserves the current status
quo for i.MX5
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fix a clock inaccuracy in get_time_ns (used by sleep, time, etc).
At i.MX53 power-on GPT clock is typically 55500000 Hz, and it will be used
to calc the clock multiplier. After call imx53_init_lowlevel() GPT clock
will changed (e.g. to 66666666 Hz), but multiplier not. To fix this behavior call
clock_notifier_call_chain() after changing clock in imx53_init_lowlevel().
Signed-off-by: Wjatscheslaw Stoljarski <wjatscheslaw.stoljarski@kiwigrid.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Procedure is missing, so remove its declaration.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Storing the size instead of the resource end in struct resource was
a mistake. 'size' ranges from 0 to UINT[32|64]_MAX + 1 which obviously
leads to problems. 'end' on the other hand will never exceed
UINT[32|64]_MAX. Also this way we can express a iomem region covering
the whole address space.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This change is necessary because valid source argument for the clko command
can be negative.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for ConnectCore® i.MX51 board from Digi International.
A separate option includes support for debugging board for this module.
Some code taken from the bootloader U-Boot and patch from Digi.
Functional of Ethernet not tested yet.
barebox 2012.05.0-00316-g4024d9c-dirty #0 Wed Jun 6 13:08:25 MSK 2012
Board: ConnectCore i.MX51
Module Variant: i.MX515@600MHz, PHY, Acceleromter (0x0b)
Module HW Rev : 02
Module Serial : B111156789
mc13xxx-spi@mc13xxx-spi0: Found MC13892 ID: 0x0045d0 [Rev: 2.0a]
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: Bad block at 0x00ce0000
nand_read_bbt: Bad block at 0x05bc0000
nand_read_bbt: Bad block at 0x0bc40000
ehci@ehci0: USB EHCI 1.00
detected i.MX51 rev 3.0
imx-esdhc@mci0: registered as mci0
imx-esdhc@mci1: registered as mci1
Malloc space: 0x95f00000 -> 0x97efffff (size 32 MB)
Stack space : 0x95ef8000 -> 0x95f00000 (size 32 kB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment
running /env/bin/init...
Hit any key to stop autoboot: 3
barebox@ConnectCore i.MX51:/
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We must check pointer to function rather than result.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently, both SDHC clock source is PLL3. We can raise clock
for SDHC driver by change source from PLL3 to PLL2.
Below, is debug ouputs with old and new settings.
Detection (PLL3):
set clock: wanted: 400000 got: 375000
Operation (PLL3):
set clock: wanted: 25000000 got: 18000000
Operation SD4.0 (PLL3):
set clock: wanted: 52000000 got: 27000000
Detection (PLL2):
set clock: wanted: 400000 got: 399639
Operation (PLL2):
set clock: wanted: 25000000 got: 23750000
Operation SD4.0 (PLL2):
set clock: wanted: 52000000 got: 41562500
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Steffen Trumtrar
Sascha Hauer
Eric Bénard
Renaud Barbier
Marc Reilly
Wjatscheslaw Stoljarski (Slawa)
Alexander Shiyan
Juergen Beisert
Christian Kapeller