The modules from cogent use a 1.8V nand
And have the mci card detect broken as they use the flash vdd as vdd for the
cd which need > 2V
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
for bootp specify the module version via client_id as
%{BOARD}-%{VERISON}
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'ron' => 72:6F:6E
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'ron' => 72:6F:6E
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The OUI will be 'ron' => 72:6F:6E
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
use the first 3 byte of the id of a 1-wire
or 6 if no OUI provided device to provide an Ethernet address
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
Based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we print the correct size
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we to have specific phy init to fix chip issue link detection support
based on linux 3.6
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
to allow to register an array of drivers
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes a linker error when PBL_IMAGE=n and DO_LOW_LEVEL_INIT=n.
In this configuration the symbol reset() was present multiple times,
and prevented the barebox image to be linked.
Signed-off-by: Christian Kapeller <christian.kapeller@cmotion.eu>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch remove a superfluous DCD command in TX53-xx30 flash header.
The entry DCD_WR_CMD(0x21c) just duplicates the contents of the last
imx_flash_header_v2 struct member dcd.
Removal of this DCD entry is needed to make the TX53 board boot again
from NAND.
Signed-off-by: Christian Kapeller <christian.kapeller@cmotion.eu>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the phy reset neet to be done before the fec driver is registered
as we accesst the phy at the fec probe time
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In the nios2 generic board generic.c file, use the
new barebox_add_memory_bank to init ram memory.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will be use by at24 driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This returns an I2C client bound to the "dummy" driver, intended for use
with devices that consume multiple addresses. Examples of such chips
include various EEPROMS (like 24c04 and 24c08 models).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is need for sequential read/write.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is needed for i2c-gpio support
Based on linux 3.7-rc2
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can show the this of i2c busses
set the bus device as parent of all devices.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as in linux
SD/MMC support only mode 0 or 3 (if 0 not supported by the spi master)
so if the mode is not 3 force 0
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
so we can detect sd card version 2.0 on spi
as we need to the OCR_HCS on version 2.0 regardless if it's a SPI or not
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The spec says: "the CMD8 CRC verification is always enabled.
The Host shall set correct CRC in the argument ofCMD8. If
CRC error is detected, card returns CRC error in R1 response
regardless of command index."
Make it simple, and compute crc on every commands.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This effectively reverts:
| commit f9df22b002
| Author: Alexander Shiyan <shc_work@mail.ru>
| Date: Mon Oct 8 10:35:04 2012 +0400
|
| Add more generated files to .gitignore
barebox* is not limited to the toplevel directory, so this ignores
all files starting with 'barebox' from which we have several we do
not wish to ignore. Add barebox-flash-image to the ignore list which
seemed to be the motivation for the original patch.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alexander Shiyan <shc_work@mail.ru>
As a new implementation of Y-Modem protocol is available,
switch from old implementation to the new one :
- remove old xyzModem* files
- remove old command loady2
- rename command loady2 to loady
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current Y-Modem implementation has some limitations:
- Y-Modem/G protocol is not supported
- Multiple files (aka. batch) transfers are not supported
- Transfer speed over fast lines (USB console) is slow
- Code is not trivial to maintain (personnal opinion)
This implementation tries to address all these points by
introducing loady2 command.
The effects are :
- transfer speed for Y-Modem over USB jumps from 2kBytes/s
to 180kBytes/s
- transfer speed for Y-Modem/G jumps to 200kBytes/s
- multiple file transfers are possible
This command was tested on a USB console and UART 9600bps
serial line :
- NAKs (and retransmissions) were tested for faulty
serial lines
- multiple file transfers were tested
- Y-Modem, Y-Modem/G and X-Modem transfers were tested
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When booting fails we will be immediately be back into the menu,
so the error message can't be seen. Also, boot in verbose mode
since in interactive mode the last bit of performance is not that
necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as we do not need to probe them and they have no driver or bus attached
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the rm9200 have a errata the cs0 must be used via hw cs not gpio
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this need to be handle at framework and driver level
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
