The intel cfi buffer write has a problem with writing when
the alignment of the buffer in memory is smaller than the
flash bus width.
This patch fixes a alignment problem which may show during this
scenario:
- 32 or 64 attached NOR flash
- flashing an image directly from network to the nor flash
The involved network driver is "smc9111.c".
The data that comes from the network stack and should be written into
the flash isn't 32 bit aligned (at least with this network driver).
This is probably due to the 48 bit wide ethernet addresses.
However the "cfi_flash.c" driver doesn't handle this situation, and
accesses the not-aligned address with a 32 bit pointer.
This patch fixes the problem by reducing the access width if an
aligment problem between source and destination is found.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
'reduce the number of loops by the width of the port' means
a simple len / width. Do not try to be clever by shifting
and doing it wrong.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes:
drivers/usb/gadget/pxa27x_udc.c:1263:13: warning: 'pxa27x_change_interface' defined but not used [-Wunused-function]
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
ISP150x product line have same identifier, we can print these
chips as ISP150x.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added ULPI detection function.
Same function from isp1504 driver removed.
Used implementation from Linux kernel.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These registers can be used for any standart ULPI chip,
not only for ISP1504.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Wait until the reset bit is actually cleared instead of some
arbitrary delay (which caused problems with a PHY which was in some
energy saving mode).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
First check the status at least once, then do timeout checks. Minor
cleanups also.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We are already setup voltages from capabilities register.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add support for KS8851 16bit MLL chip from Micrel Inc.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When programming or erasing a page, don't wait
systematically for 3s, but finish the operation as soon as
the hardware has finished, and timeout if 3 seconds have
passed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Patch 2c54046510 introduces a private structure
for the S3C based UARTs but still reserves the memory for the smaller
structure which fails at runtime.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will ensure that we send an other packet only when the first one is send.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If a read or write operation encounters an error, the card
might stay in "recv" or "data" state, and never get back to
"tran" state.
In these cases, the host is required to send a CMD12 (end
transmission) to switch the FSM of the card back to "tran"
state, as described in MMC Specification, chapter "Data
Transfer Mode".
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do not use dev->priv as a register base, but use a driver private
struct instead. Also, remove usage of dev->type_data
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We currently do not allow to unregister a device when it
has children. However, the return value is seldomly checked.
Also this breaks for hot pluggable devices like USB which we have
to unregister when they disappear. The best way to fix this is to
unregister our children and also the partitions on the unregistered
device.
We unregister the device first and then afterwards the children.
We do this because for example network devices have a miidev as
child which they unregister themselves. So we only have to
unregister the children which are not cleaned up by the drivers,
namely fs devices.
Also, unregister all partitions on a disappearing device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As pxafb can rely on a PWM to control backlight, and because
driver dependencies are hard to deal with, remove automatic
enable of PXAFB on probe.
The user should in its environment do a :
- fb0.enable=1
This way, the PWM has been probed and is ready to work, and
the pxafb backlight control works.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add PXA embedded pulse width modulator support. The PWM can
generate signals from 49.6kHz to 1.625MHz.
The driver is for pxa2xx family. The pxa3xx was not handled yet.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add variables to control the duty_ns and period_ns of PWM
chips. When these variables are set, a call to either
pwm_enable() or pwm_config() is performed to enforce the
setup values.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds framework support for PWM (pulse width modulation)
devices.
A new pwm can be registered from a hardware driver using
pwmchip_add(). It can then be requested from a client driver using
pwm_request(). A string is used as a unique identifier for the
pwms. It should usually be initialized by the hardware drivers
using dev_name(dev). The client API is the same as currently
in the Linux Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Uwe Hermann
Jean-Christophe PLAGNIOL-VILLARD
Alexander Shiyan
Marek Belisko
Wolfram Sang
Jan Weitzel
Robert Jarzmik
Juergen Beisert
Eric Bénard