The nand command is for bad block handling which some do not need.
So make it optional, but with default y.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds BCH ecc support to the omap nand driver. The BCH
error correction allows for up to 8 bit error correction. It is
also needed for booting from nand on omap4.
This is based on code from Sukumar Ghorai <s-ghorai@ti.com>:
[PATCH] omap3: nand: bch ecc support added
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On omap we use different ecc modes for different purposes. The initial
boot code has to be written with hardware ecc whereas Linux usually uses
software ecc. To be able to write in both modes with a sinlge barebox
image introduce a eccmode device parameter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If compiled without gpio support the linker will throw the
gpio functions away anyway, so make the omap kconfig entries
a bit easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Give this omap specific entry an omap namespace. Also, remove
unnecessary dependency to omap2/3 in nand Kconfig.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The original plan was to add all omap devices into the boards/omap
directory. Anyway, there will be reasons to put a board somewhere
else, so move the generic parts into the omap architecture directory.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current gpio support is derived from the kernel which allows
for support for omap2/3/4 in a single kernel. We do not need this
here, so make it more simple to be able to add omap4 support later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise we end up with errno not being set correctly
if a filesystem driver uses the standard open/close/read/write
functions to access its backing store.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Most cards do not answer if some reserved bits
in the ocr are set. However, some controllers
can set bit 7 (reserved for low voltages), but
how to manage low voltages SD card is not yet
specified.
based on the original U-Boot patch from
Stefano Babic <sbabic@denx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
if CONFIG_DEFAULT_ENVIRONMENT_PATH="" then
$(DEFAULT_ENVIRONMENT_PATH) expands to 'defaultenv "" '
The "" would cause every single file found in $(srctree) to be included in
$(ENV_FILES). This would then cause scripts/mod/sumversions.c to get
recompiled using $(CC) and fail compilation if $(CC) points to a newlib
cross compiler
Signed-off-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sync these limits with the Linux kernel. This allows support for NAND devices
with page size of 4k.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Do the same ECC handling and ECC size in barebox than the kernel does.
Currently its done for S3C2440 based systems only, as I have no idea how to
manage it on a S3C2410 based system.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When booting from NAND, its important to know the correct page size. When
the NAND is used as the boot source, four dedicated pins are used to configure
the correct page size and address cycles. These pins can be read back in one
of the NFC registers to parametrize the load function.
This patch also extends the read routine to support more than four address
cycles on demand.
BTW: At least some mini2440s are misconfigured to use five address cycles for
a NAND device that is known to need only four address cycles. In this case the
vendor is at our side: This NAND simply ignores any additional address cycles
than required.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Something was to be done here. But I do not remember what. As it works also
without it, remove this dead code.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
After running the 'nand_boot_test' command, any usage of the NAND fails with
a IO error. This happens due to the load routine disables the NAND controller
after loading the image.
This patch re-enables the NAND controller again after running the test.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
before we can only support tftp
so keep it as default
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
256k(barebox)ro,128k(bareboxenv),1536k(kernel),-(root)
so we will match the erase block size
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sascha Hauer
Jean-Christophe PLAGNIOL-VILLARD
Franck JULLIEN
Jon Ringle
Baruch Siach
Juergen Beisert
Juergen Beisert