When booting from NAND, its important to know the correct page size. When
the NAND is used as the boot source, four dedicated pins are used to configure
the correct page size and address cycles. These pins can be read back in one
of the NFC registers to parametrize the load function.
This patch also extends the read routine to support more than four address
cycles on demand.
BTW: At least some mini2440s are misconfigured to use five address cycles for
a NAND device that is known to need only four address cycles. In this case the
vendor is at our side: This NAND simply ignores any additional address cycles
than required.
Signed-off-by: Juergen Beisert <jbe@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
before we can only support tftp
so keep it as default
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
256k(barebox)ro,128k(bareboxenv),1536k(kernel),-(root)
so we will match the erase block size
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Often enough the exception vectors are not on TEXT_BASE (for example
on i.MX SoCs in internal boot mode), so the board specific code did
not map the exception vectors to 0x0 but whatever happens to be on
TEXT_BASE. Also, the current section-only mapping requires the
exception vectors to be on a 1MB boundary.
Instead, create the possibility to create second level tables and
use this to map a copy of the exception vectors in a board
independent way.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To prevent turning on the display before the signals are stable.
Also, put the LCD_CS pin in the same mode as the kernel does to
prevent flickering.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also adapt the config file to the default environment.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With this patch barebox can now be booted from RAM, NOR and NAND on the
mini2440 platform. 'CONFIG_S3C24XX_NAND_BOOT' must still be 'y' to be able to
boot from NAND.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The default configuration of the mini2440 in the current 2.6.37 kernel uses
a flash based BBT. So, the barebox for the mini2440 must also use one, to be
in sync with the kernel about bad blocks in the flash.
Due to the used OOB layout, the generic BBT description coming with the
framework can be used.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Without this modification saving a modified environment ends with:
mini2440:/ saveenv
saving environment
could not open /dev/env0: Read-only file system
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is required in order to enable booting from NAND, when there is no
other first level bootlader.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If the SDRAM type will change in the future, only the 'config.h' must be
adapted to the new settings. The real size will be read back from this setting.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is required in order to enable booting from NAND and to avoid any visible
garbage on the screen until the pins are really set.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is required in order to enable booting from NAND and using the generic
S3C2440 setup routines.
Two types of SDRAM devices are known to be shipped by FriendlyARM. This config
should work on both of them. But it is really tested only for the HY57V561620
type.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is required in order to enable booting from NAND and using the generic
S3C2440 setup routines.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
At least partly. We have pads in barebox that we do
not have in the kernel. Also, this with this patch we
do not set the sion bit which the kernel does.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
we use the board revision to specify to the linux kernel the type of lcd
we use. So we can have only one machine for those 3 boards:
- sam9m10-ekes (LG)
- sam9g45-ekes (LG)
- sam9m10g45-ek (Truly)
today we support 2 lcds model:
- LG philips LB043WQ1
- Truly TFT1N4633-E
by default we select the Truly as the sam9m10g45-ek is the most common board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Also, make sure that the usb ports are in ulpi mode before configuring
the iomuxer. Otherwise the ulpi transceiver cannot be initialized correctly.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
