Fow now use Soft ECC for nand util we add the PMECC.
On-chip and board related peripherals definitions.
Basic implementation for VB board.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On the sam9x5 series we now support 1 or 2 macb.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
set vendor-id to barebox-at91rm9200ek and the kernel over nfs
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the mainline kernel does not enable the bootp support by default
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since we do not have ISP1504-related functions, we migrated to ULPI.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because CPU frequency setup called after power initialization,
this call now is not necessary.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
FIXME: part of or no data is written. File copy ends
with message: "atmel_mci@atmel_mci0: command/data timeout"
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- change the kernel and rootfs locations
- correct the NAND mtd partitions
- fix the DDR RAM location(so BareBox load address)
- expect the root file system type to be UBIFS
Signed-off-by: Asen Chavdarov Dimov <dimov@ronetix.at>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The imx51 lowlevel setup code currently sets the full cpu
speed only for TO3. It turned out that this is not a TO
specific hack but a hack for older babbage boards. Move
the lowlevel init after babbage_power_init() so that we
can remove the hack from the generic i.MX51 lowlevel
function. As this potentially changes the UART clock we
have to flush the console beforehand and call the clock
notifier afterwards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image sizes have been hardcoded to 256K. This is inefficient
for smaller images and nonfunctional for bigger images. Calculate
the image size during compile time and use it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
imx27_add_mmc0 really registered SDHC2. Fix this by adding a
imx27_add_mmc1 and use this in the pca100 board file. Also add
imx27_add_mmc2 helper for register SDHC3.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add a OMAP4 specific GMPC nand config for pcm049 and phyCARD-A-XL2 to increase
performance. Also add the possiblility to pass a board GPMC nand config.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The image built with pcm038_defconfig is >256k so increase
the size of the barebox partition.
Signed-off-by: Teresa Gámez <t.gamez@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
drop kernelimage_type bootm now boots all of them.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Support for omap4 based Phytec phyCARD-A-XL2 board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
update fancy prompt to be the same as the other Atmel board
use the same feature on 9g10ek and 9261ek
- use tlsf
- enable MMU
- set max size to 256KiB
- bootm: add initrd support
- nand: drop non used hw ecc and oob device
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
most of the board does not have a nor soldered
update the nand partition table to boot from nand with bootstrap
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>