Once the MDIO state machine has been initialized and enabled, it
starts polling all 32 PHY addresses on the MDIO bus, looking for
an active PHY. Add a 5 ms delay, so all PHYs are for sure detected.
This problem was detected on the cmc board with a KSZ8864 switch.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The PHY driver was too verbose and corrupted the boot message display
like this:
...
Net: Ethernet PHY: KSZ8873 @ 0x02
DaVinci-EMAC
...
Turn printf() into debug() so we get the expected output again:
...
Net: DaVinci-EMAC
...
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Paulraj Sandeep <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The omap serial names have changed from ttySx to ttyOx,
so the console should be also changed to support this.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Steve wants to transfer maintainership of OMAP4 boards
to me as he is not working on these boards lately.
CC: Steve Sakoman <steve@sakoman.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Change the default console from ttyS2 to ttyO0 to
match the Linux default for the EVM.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Building without option CONFIG_DISPLAY_CPUINFO leads to
this warning:
sys_info.c:50:14: warning: 'rev_s_37xx' defined but not used
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enable high capacity to host capability.
Fixes eMMC detection on boot from MMC/SD card.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
split-up spl.c into spl.c, spl_mmc.c and spl_nand.c. This avoids problems
with missing defines if a board does not use mmc or nand. This includes
adding spl_ prefix to some functions which are now public. spl_image_t is now
a public type. Added some of the common functions to omap-common.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Implements the saving of boot params passed by OMAP3 ROM code.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add NAND SPL support to the devkit8000 config
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Support for the new spl structure. Using the interface defined by Aneesh V for
OMAP4
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3 relied on the memory config done by X-loader or Configuration Header. This
has to be reworked for the implementation of a SPL. This patch configures RAM
bank 0 if CONFIG_SPL_BUILD is set. Settings for Micron-RAM used by devkit8000
are added to mem.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Moves the early UART clock setup setup_clocks_for_console() from
preloader_console_init() to s_init() of OMAP4.
This is done to prepare for OMAP3 integration.
This patch was posted seperatly to the mailinglist but I decidet - since it is
a prereqesit for this patch to add it. Former port to ML:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Without this change CS's configured for synchronous clocking cannot
read data.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts. The patch also combines the CS configuration
for the overo and igep0020 boards per request.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for 88E3015 PHY for Marvell GplugD board.
This patch depends on series of patch which adds support for Marvell
GuruPlug-Display.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
This patch enables ethernet support for Marvell GplugD board. Network
related commands works.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds generic GPIO driver framework support for Marvell SoCs.
To enable GPIO driver define CONFIG_MARVELL_GPIO and for GPIO commands
define CONFIG_CMD_GPIO in your board configuration file.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Since commit d388298a59 by
Stefano Babic this file is no longer needed so delete it.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 041c542219.
The lines removed by this commit weren't redundant. The logic is (and
probably should be better commented):
Find the intersection of the advertised capabilities of both sides of
the link (lpa).
From that intersection, find the highest capability we can run at
(that will be the negotiated link).
Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL).
The code will now set phydev->speed to 100, and phydev->duplex to 1,
but this link does not support 100FULL.
Kudos to Andy Fleming <afleming@gmail.com> for binging this to
attention and for the explanation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is a trivial fix in the documentation, which corrects
board_init_r() source reference.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The MAC address stored in the inventory eeprom begins at offset 1.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
On some systems, we get a warning when %lu is used with size_t's, so
use the correct format string.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The new sanity check introduces a printf warning for some systems:
eth.c:233: warning: format '%zu' expects type 'size_t', but argument 3 has type 'int'
Rather than tweak the format string, use the new assert() helper instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Recent commit a4814a69d3 cleaned up generation of
asm-offsets.s for SoC dirs, but missed adding it to the ignore
list which makes it show up in `git status`.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There is no code anywhere that references BOOTFLAG_* so remove these
defines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Commit 093498669 (Put common autoload code into auto_load() function)
broke handling of autoload environment variable not being set.
The bootp/dhcp code will just keep on requesting IP address forever
and never start TFTP download.
Fix it by moving TftpStart() outside the conditional like it was before.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).
Signed-off-by: Stefan Roese <sr@denx.de>
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Heiko Schocher
Thomas Weber
Aneesh V
Sanjeev Premi
Balaji T K
Sandeep Paulraj
Simon Schwarz
Philip Balister
Philip Balister
Ajay Bhargav
Joe Hershberger
Wolfgang Denk
Linus Walleij
Albert ARIBAUD
Marek Vasut
Vladimir Zapolskiy
Dirk Behme
Holger Brunck
Vadim Bendebury
Mike Frysinger
Peter Korsgaard
Stefan Roese
Weirich, Bernhard
Jason Kridner