The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.
This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
- Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
- Switch between 4P2 Linear Regulator and Battery, using whichever has
the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
the same as the pre-patch behaviour)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
- Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
- Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch has some parts connected together:
- Use _gd in bss section which is automatically cleared
Location at SPL_MALLOC_END wasn't cleared at all
- Use MALLOC_F_LEN(early alloc) instead of FULL MALLOC
(mem_malloc_init is not called at all)
- Simplify malloc and stack init.
At the end of SPL addr is malloc area and below is stack
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Because it is not compatible with DM where
malloc_base has to be available early and init
has to be done in ASM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Compile code with -fPIC to get GOT. Do not build SPL
with fPIC because it increasing SPL size for nothing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup gd from ASM to be availalbe for board_init_r.
Setting it up in spl_board_init is too late when
MALLOC is used.
Space for gd is located behind MALLOC area at the end of BRAM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not use specific macros for debugging.
Also remove compilation warning:
w+../arch/microblaze/cpu/interrupts.c: In function 'interrupt_handler':
w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x'
expects argument of type 'unsigned int', but argument 2 has type 'void
(*)(void *)' [-Wformat]
w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x'
expects argument of type 'unsigned int', but argument 4 has type 'void
*' [-Wformat]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not save registers below r1 stack pointer because
it is not checked by stack undeflow is not able to detect
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This way we may have very limited set of functions implemented so we
save some space.
Also it allows us to build U-Boot for any ARC core with the same one
toolchain because we don't rely on pre-built libgcc.
For example:
* we may use little-endian toolchain but build U-Boot for ether
endianess
* we may use non-multilibbed uClibc toolchain but build U-Boot for
whatever ARC CPU flavour that current GCC supports
Private libgcc built from generic C implementation contributes only 144
bytes to .text section so we don't see significant degradation of size:
--->8---
$ arc-linux-size u-boot.libgcc-prebuilt
text data bss dec hex filename
222217 24912 214820 461949 70c7d u-boot.libgcc-prebuilt
$ arc-linux-size u-boot.libgcc-private
text data bss dec hex filename
222361 24912 214820 462093 70d0d u-boot.libgcc-private
--->8---
Also I don't notice visible performance degradation compared to
pre-built libgcc (where at least "*div*" functions are had-written in
assembly) on typical operations of downloading 10Mb uImage over TFTP and
bootm.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As a preparation to ARCv2 port submission we're moving CPU slection
flags to a common location.
Also it will allow us to have more flexible CPU specification, not only
ISA version but CPU family as well checking CONFIG_ARC_CPU_xxx.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Common arch_early_init_r() is used in "arc/lib/cpu.c" for all ARC boards
so there's no sense in separate per-board definitions.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There're no other options for ARC except "generic board" so ther's no
point to define CONFIG_SYS_GENERIC_BOARD per board.
We now have it set fo all ARC boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now we may select a particular version of ARC700:
* ARC750D or
* ARC770D
It allows more flexible (or more fine tuned) configuration of U-Boot.
Before that change we relied on minimal configuration but now we may
use specific features of each CPU.
Moreover allows us to escape manual selection of options that
exist in both CPUs but may have say different version like MMUv2 in
ARC750D vs MMUv3 in ARC770D.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
It's prohibited to put branch instruction in the very end of zero-delay
loop. On execution this causes "Illegal instruction" exception.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some SoC need to redirect the saic to aic to make the interrupt to
work, here add a weak function to be replaced by real function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Peng Fan
Tom Rini
Graeme Russ
Ye.Li
Michal Simek
Alexey Brodkin
Igor Guryanov
Heiko Schocher
Bo Shen