Commit Graph

2491 Commits

Author SHA1 Message Date
Heiko Schocher 210c8c00aa powerpc: keymile: Add a check for the PIGGY debug board
Check the presence of the PIGGY on the keymile boards mgcoge,
mgsuvd and kmeter1. If the PIGGY is not present, dont register
this Ethernet device.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-24 00:39:06 +01:00
Heiko Schocher de0443614a powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-01-24 00:36:19 +01:00
Kumar Gala 18af1c5f0f 85xx: Add a 36-bit physical configuration for MPC8572DS
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23 17:09:18 -06:00
Kumar Gala c51fc5d53c 85xx: Handle eLBC difference w/36-bit physical
The eLBC only handles 32-bit physical address in systems with 36-bit
physical.  The previos generation of LBC handled 34-bit physical
address in 36-bit systems.  Added a new CONFIG option to convey
the difference between the LBC and eLBC.

Also added defines for XAM bits used in LBC for the extended 34-bit
support.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23 17:08:28 -06:00
Kumar Gala 72a9414a8e 85xx: Use BR_ADDR macro for NAND chipselects
Use the new BR_ADDR macro to properly setup the address field of the
localbus chipselects used by NAND.

This allows us to deal with 36-bit phys on these boards in the future.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23 17:08:28 -06:00
Kumar Gala aca5f018a8 85xx: Introduce CONFIG_SYS_PCI*_IO_VIRT for FSL boards
Introduce a new define to seperate out the virtual address that PCI
IO space is at from the physical address.  In most situations these are
mapped 1:1.  However any code accessing the bus should use VIRT.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:13 -06:00
Kumar Gala 5af0fdd81c 85xx: Introduce CONFIG_SYS_PCI*_MEM_VIRT for FSL boards
Introduce a new define to seperate out the virtual address that PCI
memory is at from the physical address.  In most situations these are
mapped 1:1.  However any code accessing the bus should use VIRT.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:13 -06:00
Kumar Gala a6e04c344a 85xx: Use CONFIG_SYS_{PCI*,RIO*}_MEM_PHYS for physical address on FSL boards
Use the _MEM_PHYS defines instead of _MEM_BUS for LAW and real address fields
of TLBs.  This is what we should have always been using from the start.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:13 -06:00
Kumar Gala 5f91ef6acd 85xx: Convert CONFIG_SYS_PCI*_IO_BASE to _IO_BUS for FSL boards
Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2009-01-23 17:03:13 -06:00
Kumar Gala 10795f42cb 85xx: Convert CONFIG_SYS_{PCI*,RIO*}_MEM_BASE to _MEM_BUS for FSL boards
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:13 -06:00
Kumar Gala c953ddfd56 85xx: separate FLASH BASE virtual from physical address
Added a CONFIG_SYS_FLASH_BASE_PHYS for use as the physical address and
maintain CONFIG_SYS_FLASH_BASE as the virtual address of the flash.

This allows us to deal with 36-bit phys on these boards in the future.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:13 -06:00
Kumar Gala 52b565f5ad 85xx: separate PIXIS virtual from physical address
Added a PIXIS_BASE_PHYS for use as the physical address and maintain
PIXIS_BASE as the virtual address of the PIXIS fpga registers.

This allows us to deal with 36-bit phys on these boards in the future.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2009-01-23 17:03:13 -06:00
Wolfgang Denk 5df70e91c7 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2009-01-23 22:48:06 +01:00
Ron Madrid 5bb907a492 mpc83xx: New board support for SIMPC8313
This patch will create a new board, SIMPC8313, from Sheldon Instruments.  This
board boots from NAND devices and is configureable for either large or small
page devices.  The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support.  The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.

Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-23 11:31:18 -06:00
Wolfgang Grandegger 6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Dave Liu 1ac5744e33 mpc83xx: enable eLBC NAND support for MPC8315ERDB board
Signed-off-by: Dave Liu <daveliu@freescale.com>
2009-01-23 10:32:45 -06:00
Michal Simek e9b737deb2 microblaze: Add cache flush 2009-01-23 10:39:59 +01:00
Michal Simek 330e55459b microblaze: Change microblaze-generic config file
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:59 +01:00
Michal Simek 52a822ed9c microblaze: Rename ml401 to microblaze-generic
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:56 +01:00
Anton Vorontsov 8b34557c54 mpc83xx: Add PCI-E support for MPC837XEMDS boards
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.

PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-21 18:43:50 -06:00
Anton Vorontsov 8f11e34b31 mpc83xx: Add PCI-E support for MPC8315ERDB boards
MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's
support them.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2009-01-21 18:43:50 -06:00
Kim Phillips be4880ebe4 Merge branch 'master' into next 2009-01-21 18:38:51 -06:00
Matthias Fuchs 3ba605d4be ppc4xx: Add loadpci command to esd's CPCI4052 and CPCI405AB boards
This patch adds esd's loadpci BSP command to CPCI4052 and
CPCI405AB board. This requires CONFIG_CMD_BSP and CONFIG_PRAM.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-14 11:20:07 +01:00
Wolfgang Denk bae6d5e412 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2009-01-14 00:26:48 +01:00
Haiying Wang b5f65dfa9a Some changes of TLB entry setting for MPC8572DS
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)

- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2009-01-13 16:58:46 -06:00
Becky Bruce 3e3fffe3ba mpc8610hpcd: Fix PCI mapping concepts
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately.  This makes the code easier to read
and understand, and facilitates mapping changes going forward.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-01-13 15:27:46 -06:00
Becky Bruce 79e436cad3 sbc8641d: Fix PCI mapping concepts
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately.  This makes the code easier to read
and understand, and facilitates mapping changes going forward.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
2009-01-13 15:27:45 -06:00
Jean-Christophe PLAGNIOL-VILLARD 8a48686fac m501sk: move to the common memory setup
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-06 21:38:01 +01:00
Jean-Christophe PLAGNIOL-VILLARD d481c80d78 at91rm9200: rename lowlevel init value to CONFIG_SYS_
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-01-06 21:37:39 +01:00
Wolfgang Denk f85cd46918 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-12-30 23:30:47 +01:00
Peter Tyser 1f03cbfae2 XPedite5200 board support cleanup
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-29 12:46:36 -06:00
Paul Gortmaker 58da8890d5 sbc8548: use proper PHY address
The values given for the PHY address were wrong, so the code
read no valid PHY ID, and fell through to the generic PHY
support, which would work on 1000M but would not auto negotiate
down to 100M or 10M.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-12-19 18:32:48 -06:00
Paul Gortmaker ad22f9273c sbc8548: enable command line editing by default.
Lets make things a bit more user friendly.  It isn't 1985 anymore.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-12-19 18:32:47 -06:00
Paul Gortmaker bd93105fa1 sbc8548: don't enable the 3rd and 4th eTSEC
These interfaces don't have usable connectors on the board, so don't
bother enumerating or configuring them.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2008-12-19 18:32:47 -06:00
Peter Tyser ccf0fdd02b XPedite5370 board support
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19 18:11:49 -06:00
Haavard Skinnemoen cb54732052 Merge branch 'fixes' into cleanups
Conflicts:

	board/atmel/atngw100/atngw100.c
	board/atmel/atstk1000/atstk1000.c
	cpu/at32ap/at32ap700x/gpio.c
	include/asm-avr32/arch-at32ap700x/clk.h
	include/configs/atngw100.h
	include/configs/atstk1002.h
	include/configs/atstk1003.h
	include/configs/atstk1004.h
	include/configs/atstk1006.h
	include/configs/favr-32-ezkit.h
	include/configs/hammerhead.h
	include/configs/mimc200.h
2008-12-17 16:53:07 +01:00
Jean-Christophe PLAGNIOL-VILLARD 13095b2f07 MIPS: qemu_mips: move env storage just after u-boot
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-12-17 22:27:27 +09:00
Wolfgang Denk 9e2a79b4c5 include/configs/at91cap9adk.h: fix typo.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16 23:13:46 +01:00
Wolfgang Denk 455ae7e87f Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16 01:02:17 +01:00
Peter Tyser ba490b7761 Remove unused CONFIG_ADDR_STREAMING defines
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-14 12:42:42 +01:00
Jean-Christophe PLAGNIOL-VILLARD 3aed3aa2c1 Fix new found CFG_
Also fix some minor typos.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-14 10:55:30 +01:00
Wolfgang Denk 89d56f5503 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2008-12-13 00:36:25 +01:00
Wolfgang Denk f6704e49d6 Merge branch 'master' of git://git.denx.de/u-boot-sh 2008-12-13 00:26:19 +01:00
Nobuhiro Iwamatsu 5783758fd2 sh: Update ms7722se board config
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-12-10 23:11:35 +09:00
Matthias Fuchs 1951f847f0 ppc4xx: Update TEXT_BASE for CPCI405 boards
This patch fixes building U-Boot for CPCI405 boards.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-10 15:11:15 +01:00
Stefan Roese 8c92af7b2f ppc4xx: Remove some features from ALPR to fit into 256k again
Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-10 15:10:54 +01:00
Michal Simek 8fab49ea91 microblaze: Remove XUPV2P board
---

Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.

This change will go through microblaze custodian tree.
2008-12-10 09:25:33 +01:00
Michal Simek 99ba6f3535 microblaze: Remove CONFIG_LIBFDT due to error in common files 2008-12-10 09:25:33 +01:00
Michal Simek e7d591e823 microblaze: Fix ml401 uart16550 setting
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-12-10 09:25:33 +01:00
Wolfgang Denk 13d36ec849 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-12-09 01:06:14 +01:00
Niklaus Giger b03150b52e Use new CONFIG_SYS_VXWORKS parameters for Netstal boards
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
2008-12-07 00:19:04 +01:00
Peter Tyser 561858ee7d Update U-Boot's build timestamp on every compile
Use the GNU 'date' command to auto-generate a new U-Boot
timestamp on every compile.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-06 23:36:43 +01:00
Nicolas Ferre 89a7a87f08 at91: Choose environment variables location within make config target
This patch adds the possiblity to choose the media where the environment will
be located. This allow to choose this fundamental configuration without editing
config files.

Documentation file added.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Stelian Pop <stelian@popies.net>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-06 13:11:14 +01:00
Wolfgang Denk 90665e3d97 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-12-05 00:27:19 +01:00
Wolfgang Denk 762bd90cbb Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-12-05 00:17:16 +01:00
Dave Liu dc889e8653 85xx: fix the wrong DDR settings for MPC8572DS
The default DDR freq is 400MHz or 800M data rate,
the old settings is pure wrong for the default case.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-12-04 03:15:44 -06:00
Kumar Gala ea154a1781 FSL: Moved BR_PHYS_ADDR for localbus to common header
The BR_PHYS_ADDR macro is useful on all machines that have local bus
which is pretty much all 83xx/85xx/86xx chips.

Additionally most 85xx & 86xx will need it if they want to support
36-bit physical addresses.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-12-04 03:15:43 -06:00
Jon Loeliger 5a105a333d Removed unused CONFIG_L1_INIT_RAM symbol.
Prevent further viral propogation of the unused
symbol CONFIG_L1_INIT_RAM by just removing it.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-12-03 22:48:32 -06:00
Dave Liu 9b0ad1b1c7 85xx: remove the unused ddr_enable_ecc in the board file
The DDR controller of 8548/8544/8568/8572/8536 processors
have the ECC data init feature, and the new DDR code is
using the feature, and we don't need the way with DMA to
init memory any more.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
2008-12-03 22:44:48 -06:00
Jean-Christophe PLAGNIOL-VILLARD 4a129a57d9 at91rm9200dk: Fix typo
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-02 22:01:42 +01:00
Jon Loeliger 801a194616 Removed unused CONFIG_L1_INIT_RAM symbol.
Prevent further viral propogation of the unused
symbol CONFIG_L1_INIT_RAM by just removing it.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2008-12-01 10:28:50 -06:00
Jon Loeliger f698738e46 86xx: Fix non-64-bit compilation problems.
Introducing 64-bit (36-bit) support for the MPC8641HPCN
failed to accomodate the other two 86xx boards.
Introduce definitions for CONFIG_SYS_CCSRBAR_PHYS_{LOW,HIGH}
CONFIG_SYS_CCSR_DEFAULT_DBAT{U,L} and CONFIG_SYS_CCSR_DEFAULT_IBAT{U,L}
with nominal 32-bit values.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
2008-12-01 10:28:49 -06:00
Wolfgang Denk 06efc122a0 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2008-11-25 11:47:41 +01:00
Wolfgang Denk 95d4b70d50 Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx 2008-11-25 11:45:34 +01:00
Wolfgang Denk f9b354faa0 Merge branch 'master' of git://git.denx.de/u-boot-ubi 2008-11-25 11:40:57 +01:00
Matthias Fuchs 24eea623d4 ppc4xx: Remove unused features
This patch disables some unused features from the PCI405 configuration
to keep U-Boot image size below 192k.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-25 09:03:41 +01:00
Heiko Schocher 633639587e powerpc, keymile boards: extract identical config options
This patch extracts the identical config options for the
keymile boards mgcoge, mgsuvd and kmeter1 in a new
common config file keymile-common.h.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-24 18:41:50 -06:00
Heiko Schocher 9482a8e3d6 powerpc: keymile: Add a check for the PIGGY debug board
Check the presence of the PIGGY on the keymile boards mgcoge,
mgsuvd and kmeter1. If the PIGGY is not present, dont register
this Ethernet device.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-24 18:41:34 -06:00
Jens Scharsig 8052352f20 at91rm9200: fix broken boot from nor flash
This patch fix the broken boot from NOR Flash on AT91RM9200 boards, if
CONFIG_AT91RM9200 is defined and nor preloader is used.

Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
2008-11-24 22:10:04 +01:00
Yuri Tikhonov 1a6a00dcc5 ppc4xx: katmai: Change default config
This patch enables support for EXT2, and increases the
CONFIG_SYS_BOOTMAPSZ size for the default configuration
of the katmai boards to use them as the RAID-reference
AMCC setups.

 EXT2 enabling allows one to boot kernels from the EXT2
formatted Compact Flash cards.

 CONFIG_SYS_BOOTMAPSZ increasing allows one to boot the
Linux kernels, which use PAGE_SIZE of 256KB. Otherwise,
the memory area with DTB file (which is placed at the
end of the bootmap area) will turn out to be overlapped
with the BSS segment of the 256KB kernel, and zeroed
in early_init() of Linux.

 Actually, increasing of the bootmap size could be done
via setting of the bootm_size U-Boot variable, but it looks
like the current U-Boot implementation have some bootm_size-
related functionality lost. In many places through the U-Boot
code the CONFIG_SYS_BOOTMAPSZ definition is used directly
(instead of trying to read the corresponding value from the
environment). The same is truth for the boot_jump_linux()
function in lib_ppc/bootm.c, where U-Boot transfers control
to Linux passing the CONFIG_SYS_BOOTMAPSZ (not bootm_size)
value to the booting kernel.

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-21 11:08:02 +01:00
Dave Mitchell ddf45cc758 ppc4xx: Changed 460EX/GT OCM TLB and internal SRAM initialization
Expanded OCM TLB to allow access to 64K OCM as well as 256K of
internal SRAM.

Adjusted internal SRAM initialization to match updated user
manual recommendation.

OCM & ISRAM are now mapped as follows:
        physical        virtual         size
ISRAM   0x4_0000_0000   0xE300_0000     256k
OCM     0x4_0004_0000   0xE304_0000     64k

A single TLB was used for this mapping.

Signed-off-by: Dave Mitchell <dmitch71@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-21 11:02:04 +01:00
Stelian Pop 3e0cda071a AT91: Enable PLLB for USB
At least some (old ?) versions of the AT91Bootstrap do not set up the
PLLB correctly to 48 MHz in order to make USB host function correctly.

This patch sets up the PLLB to the same values Linux uses, and makes USB
work ok on the following CPUs:
	- AT91CAP9
	- AT91SAM9260
	- AT91SAM9263

This patch also defines CONFIG_USB_STORAGE and CONFIG_CMD_FAT for all
the relevant AT91CAP9/AT91SAM9 atmel boards.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-11-21 01:41:14 +01:00
Stelian Pop ad229a44e1 AT91: Use AT91_CPU_CLOCK in displays
Introduce AT91_CPU_CLOCK and use it for displaying the CPU
speed in the LCD driver.

Also make AT91_MAIN_CLOCK and AT91_MASTER_CLOCK reflect the
corresponding board clocks.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-11-21 01:41:14 +01:00
Heiko Schocher fed36ac5ae powerpc: 83xx: add support for the kmeter1 board
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.

- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-20 15:29:32 -06:00
Howard Gregory 2f2a5c3714 mpc83xx: Improve the performance of DDR memory
modify the CAS timings. my understanding is that these
settings decrease various wait times in the DDR interface.
Because these wait times are in clock cycles, and the DDR
clock on the 8315 RDB runs slower than on some other 83xx
platforms, we can dial down these values without a problem,
thereby decreasing the latency of memory a little.

Signed-off-by: Howard Gregory <Greg.Howard@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-11-19 18:42:54 -06:00
Kyungmin Park 8000b086b3 ARM: Add Apollon UBI support
To enable UBI on Apollon you need to uncomment the CONFIG_SYS_USE_UBI
macro.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Wolfgang Denk e0b0ec8430 Merge branch 'master' of git://git.denx.de/u-boot-mpc86xx 2008-11-18 21:40:38 +01:00
Becky Bruce d52082b12c mpc8641: Try to detect old .dts files
Since we've changed the memory map of the board, be nice and
add some checking to try to catch out-of-date .dts files.  We do
this by checking the CCSRBAR location in the .dts and comparing
it to the CCSRBAR location in u-boot.  If they don't match, a
warning msg is printed.  This isn't foolproof, but it's simple and
will catch most of the cases where an out-of-date .dts is present,
including all of the cases where a new u-boot is used with an old
standard MPC8641 .dts file as supplied with Linux.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:05 -06:00
Becky Bruce 3111d32c49 mpc8641: Support 36-bit physical addressing
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled.  With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations.  This means we have to distinguish between
the two in the config file.  The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.

Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:05 -06:00
Becky Bruce c759a01a00 mpc8641: Change 32-bit memory map
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.

The regions for some of the mappings were far larger than they
needed to be.  I have reduced the mappings to match the
actual sizes supported by the hardware.

In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them.  These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.

Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:04 -06:00
Becky Bruce bf9a8c3430 mpc86xx: Change early FLASH mapping to 1M at CONFIG_MONITOR_BASE_EARLY
We define CONFIG_MONITOR_BASE_EARLY to define the initial location
of the bootpage in flash.   Use this to create an early mapping
definition for the FLASH, and change the early_bats code to use this.

This  change facilitates the relocation of the flash since the early
mappings are no longer tied to the final location of the flash.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:04 -06:00
Becky Bruce 6bf98b1362 mpc8641: make DIAG_ADDR == FLASH_BASE
Currently, that's what it is, but it's hardcoded.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:03 -06:00
Becky Bruce 170deacb1d mpc8641: Drop imaginary second flash bank, map 8MB
There's a lot of setup and foo for the second flash
bank.  The problem is, this board doesn't actually have one.
Clean this up.  Also, the flash is 8M in size.  Get rid
of the confusing aliased overmapping, and just map 8M.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:03 -06:00
Becky Bruce 0f2d66027b mpc8641: only define CONFIG_ENV_SIZE once
It's currently defined twice inside in an if/else block, but
both halves set the same value.  Move the define outside
the if.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:02 -06:00
Becky Bruce 05df3e5a63 mpc8641: Remove extra "0" from BR2 define
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-10 10:10:01 -06:00
Jon Loeliger 33211469f7 Merge commit 'wd/master' 2008-11-10 10:04:51 -06:00
Ben Warren 96e21f86e8 Changed PPC4xx EMAC driver to require CONFIG_PPC4xx_EMAC
All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
2008-11-09 21:38:04 -08:00
Wolfgang Denk 23b7b87a37 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-11-09 00:09:51 +01:00
Wolfgang Denk c06d9bbbeb Merge branch 'master' of git://git.denx.de/u-boot-coldfire 2008-11-09 00:01:42 +01:00
Sergey Lapin 1079432e04 Custom AFEB9260 board support
This patch provides support for AFEB9260 board, a product of
OpenSource hardware and software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2008-11-04 23:47:17 +01:00
Becky Bruce 1266df8877 powerpc: change 86xx SMP boot method
We put the bootpg for the secondary cpus into memory and use
BPTR to get to it.  This is a step towards converting to the
ePAPR boot methodology.  Also, the code is written to
deal properly with more than 4GB of RAM.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-04 10:58:50 -06:00
Becky Bruce b543156068 8641HPCN: Config file cleanup
There are several items in the config file that were hardcoded
but that should really be based on other config options, since
the regions are contiguous and depend on being so.  This cleans
that up a bit.  Also, add BR_PHYS_ADDR() macro to convert
addresses into the proper format for BR registers.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-03 11:05:01 -06:00
Becky Bruce 104992fc54 powerpc 86xx: Handle CCSR relocation earlier
Currently, the CCSR gets relocated while translation is
enabled, meaning we need 2 BAT translations to get to both the
old location and the new location.  Also, the DEFAULT
CCSR location has a dependency on the BAT that maps the
FLASH region.  Moving the relocation removes this unnecessary
dependency. This makes it easier and more intutive to
modify the board's memory map.

Swap BATs 3 and 4 on 8610 so that all 86xx boards use the same
BAT for CCSR space.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-03 11:05:00 -06:00
Becky Bruce af5d100e8d mpc8641: Make PCI and RIO mutually exclusive, fix non-PCI build
You can't actually have both, and with some coming changes to
change the memory map for the board and support 36-bit physical,
we need the extra BAT that is being consumed by having both.

I also make non-PCI configs build cleanly, for the sake of sanity.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-03 11:04:59 -06:00
Becky Bruce 98693b85d4 mpc8641: Stop supporting non-PCI_PNP configs
We don't actually ever do this, remove the code so we
can stop maintaining it.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-11-03 11:04:59 -06:00
TsiChung Liew 536e7dac16 ColdFire: Add MCF5301x CPU and M53017EVB support
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
TsiChung Liew a21d0c2cc9 ColdFire: Add SBF support for M52277EVB
Add serial boot support

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
TsiChung Liew b202816c61 ColdFire: Use CFI driver for M5272C3
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
TsiChung Liew 012522fef3 ColdFire: Modules header files cleanup
Consolidate ATA, ePORT, QSPI, FlexCan, PWM, RNG,
MDHA, SKHA, INTC, and FlexBus structures and
definitions in immap_5xxx.h to more unify modules
header files. Append DSPI support for m547x_8x.
SSI cleanup. Remove USB Host structure from immap_539.h.
Apply changes to use FlexBus structures in mcf52x2's
cpu_init.c and platform configuration files.

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-11-03 09:45:58 -07:00
Wolfgang Denk 60c68d9c1c TQM8260: use CFI flash driver instead of custom driver.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-02 16:24:16 +01:00
Heiko Schocher 298e476c66 mgsuvd: remove unused defines in config file.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-11-02 16:22:20 +01:00
Wolfgang Denk 3cbd823116 Coding Style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-02 16:14:22 +01:00
Wolfgang Denk 3ec53148eb Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2008-11-01 16:18:43 +01:00
Jason Jin c57fc28947 NAND: Add NAND support for MPC8536DS board
This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.

Singed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-31 13:14:31 -05:00
Haiying Wang 6fc110bd8a NAND: Fix CONFIG_ENV_ADDR for MPC8572DS
CONFIG_ENV_ADDR should be (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE).

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-31 13:14:30 -05:00
Matthias Fuchs 76b565b69f ppc4xx: Update PMC440 board configuration
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31 10:38:08 +01:00
Ricardo Ribalda Delgado cc2dc9b08c ppc4xx: Merge xilinx-ppc440 and xilinx-ppc405 cfg
Xilinx ppc440 and ppc405 have many similarities. This patch merge the
config files of both infrastuctures

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31 10:31:02 +01:00
Stefan Roese 3befd85633 ppc4xx: Correctly configure the GPIO pin muxing on Arches
Arches doesn't use PerCS3 but GPIO43, so let's configure the GPIO
pin multiplexing correctly

Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31 10:30:28 +01:00
Wolfgang Denk a7faab9d11 Merge branch 'master' of git://git.denx.de/u-boot-mpc86xx 2008-10-30 20:57:46 +01:00
Dave Liu 1c671977dc 86xx: remove the unused definition
Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-10-30 10:43:52 -05:00
Haiying Wang c013b74975 NAND: Add support for MPC8572DS board
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.

It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.

Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 13:08:17 -05:00
Wolfgang Denk f8030519bb Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-10-27 22:31:32 +01:00
Kumar Gala c2083e0e11 86xx: Convert all fsl_pci_init users to new APIs
Converted MPC8610HCPD, MPC8641HPCN, and SBC8641D to use
fsl_pci_setup_inbound_windows() and ft_fsl_pci_setup().

With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
2008-10-24 17:35:48 -05:00
Kumar Gala 2dba0dea98 85xx: Convert all fsl_pci_init users to new APIs
Converted ATUM8548, MPC8536DS, MPC8544DS, MPC8548CDS, MPC8568MDS,
MPC8572DS, TQM85xx, and SBC8548 to use fsl_pci_setup_inbound_windows()
and ft_fsl_pci_setup().

With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
2008-10-24 17:35:12 -05:00
Kumar Gala 8ba93f68a1 86xx: Enable 64-bit PCI resources on all Freescale boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
2008-10-24 17:34:17 -05:00
Kumar Gala 0151cbaccf 85xx: Enable 64-bit PCI resources on all Freescale boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
2008-10-24 17:33:06 -05:00
Dave Liu d5b693090e 85xx: remove unused config definition
Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-10-24 16:18:33 -05:00
Georg Schardt 5deb8022c3 ppc4xx: New board avnet fx12 minimodul
This patch adds support for the avnet fx12 minimodul.
It needs the "ppc4xx: Generic architecture for xilinx ppc405"
patch from Ricardo.

Signed-off-by: Georg Schardt <schardt@team-ctech.de>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-24 17:34:26 +02:00
Ricardo Ribalda Delgado 1f4d53260e ppc4xx: Generic architecture for xilinx ppc405(v3)
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx
ppc440 boards, this patch presents a common architecture for all the
xilinx ppc405 boards.

Any custom xilinx ppc405 board can be added very easily with no code
duplicity.

This patch also adds a simple generic board, that can be used on almost
any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h

This patch is prepared to work with the latest version of EDK (10.1)

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-24 17:26:09 +02:00
Stefan Roese 485c00a57f ppc4xx: Disable DDR2 autocalibration on Kilauea for now
Since the new autocalibration still has some problems on some Kilauea
boards with 200MHz DDR2 frequency we disable the autocalibration and
use the hardcoded values as done before. This seems to work reliably
on all known DDR2 frequencies.

After the autocalibration issue is fixed we will enable it again.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-24 17:25:13 +02:00
Anton Vorontsov 3bf1be3c0c mpc83xx: add support for switching between USB Host/Function for MPC837XEMDS
With this patch u-boot can fixup the dr_mode and phy_type properties
for the Dual-Role USB controller.

While at it, also remove #ifdefs around includes, they are not needed.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21 18:40:01 -05:00
Anton Vorontsov b3379f3fd1 mpc83xx: add ELBC NAND support for the MPC837XEMDS boards
Though NAND chip is replaceable on the MPC837XE-MDS boards, the
current settings don't work with the default chip on the board.
Nevertheless Freescale's U-Boot sets the option register correctly,
so I just dumped the register from the working u-boot. My guess is
that the old settings were applicable for some pilot boards, not
found in the production.

This patch also enables FSL ELBC driver so that we could access
the NAND storage in the u-boot.

The NAND support costs about 45KB, so the u-boot no longer fits
into two 128KB NOR flash sectors, thus we also have to adjust
environment location: add another 128KB to the monitor length.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

It is due to hardware design and logic defect, that is the
I/O[0:7] of NAND chip is connected to LAD[7:0], so when
the NAND chip connected to nLCS3,  you have to set up the
OR3[BCTLD] = '1' for normal operation, otherwise it will have
bus contention due to the pin 48/25 of U60 is enabled.

Setup the OR3[BCTLD] = '1' , that meaning the LBCTL is not
asserted upon access to the NAND chip, keep the default state.

Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21 18:34:17 -05:00
Anton Vorontsov 00f7bbae92 mpc83xx: fix PCI scan hang on the standalone MPC837xE-MDS boards
The MPC837xE-MDS board's CPLD can auto-detect if the board is on the PIB,
standalone or acting as a PCI agent. User's Guide says:

- When the CPLD recognizes its location on the PIB it automatically
  configures RCW to the PCI Host.
- If the CPLD fails to recognize its location then it is automatically
  configured as an Agent and the PCI is configured to an external arbiter.

This sounds good. Though in the standalone setup the CPLD sets PCI_HOST
flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
any arbiter bad things will happen (here the board hangs during any config
space reads).

In this situation we must disable the PCI. And in case of anybody really
want to use an external arbiter, we provide "pci_external_aribter"
environment variable.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21 18:34:14 -05:00
Anton Vorontsov 1da83a63d8 mpc83xx: add SGMII riser module support for the MPC8378E-MDS boards
This involves configuring the SerDes and fixing up the flags and
PHY addresses for the TSECs.

For Linux we also fix up the device tree.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21 18:34:08 -05:00
Anton Vorontsov 5c2ff323a9 mpc83xx: mpc8360emds: rework LBC SDRAM setup
Currently 64M of LBC SDRAM are mapped at 0xF0000000 which makes
it difficult to use (b/c then the memory is discontinuous and
there is quite big memory hole between the DDR/SDRAM regions).

This patch reworks LBC SDRAM setup so that now we dynamically
place the LBC SDRAM near the DDR (or at 0x0 if there isn't any
DDR memory).

With this patch we're able to:

- Boot without external DDR memory;
- Use most "DDR + SDRAM" setups without need to support for
  sparse/discontinuous memory model in the software.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-21 18:31:07 -05:00
Wolfgang Denk 06c2942218 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2008-10-21 21:19:35 +02:00
Dirk Eibach d7b26d5832 ppc4xx: Add GDSys neo 405EP board support
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:35:02 +02:00
Niklaus Giger c11da19454 ppc4xx: Update configs for Netstal boards
I reorganized my config files, putting the common stuff into netstal-common.h
(got the idea by looking a amcc-common.h from Stefan).

Added stuff to boot the new powerpc linux via NFS (only tested with HCU4).

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:34:57 +02:00
Adam Graham f09f09d389 ppc4xx: Add AMCC Arches board support (dual 460GT)
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR
FLASH, UART, EEPROM and temperature sensor, along with a shared debug
port. The two 460GT's will communicate with each other via shared
memory, Gigabit Ethernet and x1 PCI-Express.

Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-21 17:34:46 +02:00
Wolfgang Denk 055b12f2ff TQM8260: environment in flash instead EEPROM, baudrate 115k
Several customers have reported problems with the environment in
EEPROM, including corrupted content after board reset. Probably the
code to prevent I2C Enge Conditions is not working sufficiently.

We move the environment to flash now, which allows to have a backup
copy plus gives much faster boot times.

Also, change the default console initialization to 115200 bps as used
on most other boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-21 11:27:53 +02:00
Heiko Schocher 360fe71e82 mgcoge: add redundant environment sector
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:08 +02:00
Heiko Schocher 53ebf0c470 mgsuvd: update size of environment
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:08 +02:00
Jason Jin 2e26d837f1 Enabled the Freescale SGMII riser card on 8536DS
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2008-10-18 21:54:08 +02:00
Liu Yu 7e183cad0c Enabled the Freescale SGMII riser card on 8572DS
This patch based on Andy's work.
Including command 'pixis_set_sgmii' support.

Signed-off-by: Liu Yu <yu.liu@freescale.com>
2008-10-18 21:54:07 +02:00
Liu Yu bff188baf9 Make pixis_set_sgmii more general to support MPC85xx boards.
The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.

Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.

Signed-off-by: Liu Yu <yu.liu@freescale.com>
2008-10-18 21:54:07 +02:00
Haiying Wang 4ca06607d6 Add ddr interleaving suppport for MPC8572DS board
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.

* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-18 21:54:05 +02:00
Kumar Gala 1c9aa76bf9 85xx: Enable interrupt and setexpr commands on Freescale 85xx boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-18 21:54:04 +02:00
Heiko Schocher a21ca95f8b mgsuvd: fix compiler warning when using soft_i2c driver
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:04 +02:00
Heiko Schocher cac9cf7875 mgsuvd: fix coding style
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:04 +02:00
Heiko Schocher e02d4a9904 mgcoge: added CONFIG_FIT to support the new u-boot image format
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD 6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Heiko Schocher f7e51b2750 mgsuvd, mgcoge: added BOOTCOUNT feature.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher 8f64da7f83 mgcoge, mgsuvd: added support for the IVM EEprom.
The EEprom contains some Manufacturerinformation,
which are read from u-boot at boot time, and saved
in same hush shell variables.

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher 67b23a3228 I2C: adding new "i2c bus" Command to the I2C Subsystem.
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher c24853644d mgcoge, mgsuvd: add board specific I2C deblocking mechanism.
As documented in doc/I2C_Edge_Conditions, adding a
board specific deblocking mechanism via CFG_I2C_INIT_BOARD
for the mgcoge and mgsuvd board.

This code was originally written by Keymile in association
with Anatech and Atmel in 1998. The Code toggels the SCL
until the SCA line goes to HIGH (max. 16 times).
And after this, a start condition is sent.

This is another approach to deblock the I2C Bus. The
soft I2C driver actually sends 9 clocks with SDA High,
and then a stop at the end, to deblock the I2C Bus.

Maybe we should use the approach from Keymile as
the new standard?

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher e5e4edd9f1 mgcoge, mgsuvd: add DTT (LM75) support.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:02 +02:00
Heiko Schocher f2202450c7 mgcoge, mgsuvd: added EEprom support.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:01 +02:00
Heiko Schocher 9661bf9d12 mgcoge, mgsuvd: add I2C support.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-10-18 21:54:01 +02:00
Haiying Wang 41410eee47 Change UEC PHY interface to RGMII on MPC8568MDS
Change UEC phy interface from GMII to RGMII on MPC8568MDS board

Because on MPC8568MDS, GMII interface is only recommended for 1000Mbps speed,
but RGMII interface can work at 10/100/1000Mbps, and RGMII interface works more stable.

Now both UEC1 and UEC2 can work properly under u-boot.

It is also in consistent with the kernel setting for 8568 UEC phy interface.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-10-18 21:54:00 +02:00
Selvamuthukumar 03e2dbb18e Remove unwanted ';' at end of define.
Currently this is not creating any problem. But it will result
in compilation error when used as below.

printf("CFG_SDRAM_CFG2 - %08x\n", CFG_SDRAM_CFG2);

Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>

continuation of the theme based on git grep "^#define CFG_.*;$" include/

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-10-14 23:03:03 +02:00
Peter Tyser abbb90666d Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE references
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-10-14 14:45:31 +02:00
Nobuhiro Iwamatsu 05c7e9070f sh: rsk7203: Add smc911x driver support to board config file
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-10-14 13:09:45 +09:00
Stefan Roese 1f6aa622e3 Merge branch 'master' of /home/stefan/git/u-boot/u-boot 2008-10-13 11:17:31 +02:00
Wolfgang Denk df4a0796e8 Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master 2008-10-12 23:56:33 +02:00
Wolfgang Denk 22a871a464 Merge branch 'master' of git://git.denx.de/u-boot-arm 2008-10-12 23:55:12 +02:00
Wolfgang Denk 1e841086df Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master 2008-10-12 23:25:50 +02:00
Wolfgang Denk 1f7bab0832 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-10-12 23:12:44 +02:00
Matthias Fuchs 35dd025c70 ppc4xx: Update DU440 config
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-10 09:38:35 +02:00
Kumar Gala f3bf927393 MPC8572DS: Fix compile warnings
Commit 445a7b3830 introduced the following
compile warnings:

cmd_i2c.c:112: warning: missing braces around initializer
cmd_i2c.c:112: warning: (near initialization for 'i2c_no_probes[0]')

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-08 15:43:28 -05:00
Guennadi Liakhovetski 1ed7a7f0f5 i.MX31: switch to CFG_HZ=1000
Switch to the standard CFG_HZ=1000 value, while at it, minor white-space
cleanup, remove CFG_CLKS_IN_HZ from config-headers. Tested on mx31ads,
provides 2% or 0.4% precision depending on the
CONFIG_MX31_TIMER_HIGH_PRECISION flag. Measured with stop-watch on 100s
boot-delay.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-10-08 18:59:02 +02:00
Haiying Wang 5297246bba Remove redundant #define for MPC8536DS
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-07 16:22:28 -05:00
Haiying Wang 445a7b3830 Add ID EEPROM support for MPC8572DS
The ID EEPROM on MPC8572DS board locates on I2C bus 1. Its the storage for
system information like mac addresses etc. This patch enables it.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-07 16:22:26 -05:00
Haiying Wang 1f3ba317a5 Minor fixes for I2C address on MPC8572DS
MPC8572DS has two i2c buses. This patch moves the DDR SPD_EEPROM to i2c bus 1
according to the board spec, and adds the 2nd i2c bus offset.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-07 16:22:22 -05:00
Jason Jin c0391111c3 Fix the incorrect DDR clk freq reporting on 8536DS
On 8536DS board, When the DDR clk is set async mode(SW3[6:8] != 111),
The display is still sync mode DDR freq. This patch try to fix
this. The display DDR freq is now the actual freq in both
sync and async mode.

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2008-10-07 15:37:08 -05:00
Mark Jackson a69a42338d MIMC200 board now uses CONFIG_DISABLE_CONSOLE
Changed MIMC200 board setup and config to use CONFIG_DISABLE_CONSOLE.
Also fixed default uImage location.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-05 21:43:49 +02:00
Wolfgang Denk 33af3e6656 TQM5200: enable support for ATAPI devices
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-01 12:34:58 +02:00
Kim Phillips 7fd0bea2e4 mpc83xx: don't disable autoboot
bootdelay set to -1 'permanently' disables autobooting, even if
bootcmd is specified.  Change to a positive value to allow
autobooting when a bootcmd is set.

Reported-by: Coray Tate <Coray.Tate@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-09-24 09:58:34 -05:00
Kim Phillips 162c41c031 mpc83xx: add h/w flash protection to board configs
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-09-24 09:58:34 -05:00
Anatolij Gustschin 5c65ecf7cd socrates: change default mtest address range
Running mtest command on socrates without specifying
an address range crashes the board. This patch changes
default mtest address range to prevent this behavior.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-09-22 21:49:19 +02:00
Anatolij Gustschin 562788b0a3 socrates: fix SPD EEPROM address
Commit be0bd8234b
changed SPD EEPROM address to 0x51 and DDR SDRAM
detection stopped working. Change this address
back to 0x50.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-09-22 21:46:56 +02:00
Wolfgang Denk dd820b03a2 ADS5121: fix typo in "rootpath" default setting
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-18 13:57:32 +02:00
Wolfgang Denk 7c803be2eb TQM8xx: Fix CFI flash driver support for all TQM8xx based boards
After switching to using the CFI flash driver, the correct remapping
of the flash banks was forgotten.

Also, some boards were not adapted, and the old legacy flash driver
was not removed yet.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-16 18:02:19 +02:00
u-boot@bugs.denx.de e99b607a5e 85xx: socrates: Add support for new image format.
Signed-off-by: Detlev Zundel <dzu@denx.de>
2008-09-13 02:05:37 +02:00
Wolfgang Denk afbc526336 Merge branch 'Makefile-next' of git://git.denx.de/u-boot-arm 2008-09-12 16:13:12 +02:00
Wolfgang Denk b476b03256 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2008-09-12 15:23:20 +02:00
Stefan Roese b18410e508 ppc4xx: Enable device tree (FDT) support in zeus board port
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-12 07:12:39 +02:00
Stefan Roese 7bf5ecfa50 ppc4xx: Fix SDRAM inititialization of multiple 405 based board ports
This patch fixes a problem introdiced with patch
bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by
initdram()].

The boards affected are:
- PCI405
- PPChameleonEVB
- quad100hd
- taihu
- zeus

Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-12 07:12:33 +02:00
Gururaja Hebbar K R b23253835f ARM OMAP : Correct Invalid Timer Register Field Declaration in omap1510.h & omap730.h
- Correct Invalid #define of MPUTIM_PTV_MASK for
   omap1510 & omap730 register definition

 MPUTIM_PTV_MASK is defined as
 #define MPUTIM_PTV_MASK		(0x7<<PTV_BIT)

 while it should have been
 #define MPUTIM_PTV_MASK		(0x7<<MPUTIM_PTV_BIT)

- Below Patch corrects the same

Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
2008-09-12 02:20:40 +02:00
Magnus Lilja 1a6337b013 i.MX31: Make the SPI bus and chip select configurable for MC13783
The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.

This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2008-09-12 01:23:44 +02:00
Jean-Christophe PLAGNIOL-VILLARD deeec4991a ap325rxa: remove duplicate CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:09 +02:00
Jean-Christophe PLAGNIOL-VILLARD 0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD 5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD 7d9b5bae5b cleanup use of CFG_ENV_IS_IN_FLASH
- #if CFG_ENV_IS_IN_FLASH
- #if (CFG_ENV_IS_IN_FLASH == 1)
- #define CFG_ENV_IS_IN_FLASH 0

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:03 +02:00
Jean-Christophe PLAGNIOL-VILLARD 93f6d72544 rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHERE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD 0b5099a841 rename CFG_ENV_IS_IN_SPI_FLASH in CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD 9656138ff1 rename CFG_ENV_IS_IN_ONENAND in CONFIG_ENV_IS_IN_ONENAND
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:59 +02:00
Jean-Christophe PLAGNIOL-VILLARD 9314cee691 rename CFG_ENV_IS_IN_NVRAM in CONFIG_ENV_IS_IN_NVRAM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:59 +02:00
Jean-Christophe PLAGNIOL-VILLARD 51bfee1920 rename CFG_ENV_IS_IN_NAND in CONFIG_ENV_IS_IN_NAND
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:58 +02:00
Jean-Christophe PLAGNIOL-VILLARD 057c849c45 rename CFG_ENV_IS_IN_DATAFLASH in CONFIG_ENV_IS_IN_DATAFLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:47:58 +02:00
Jean-Christophe PLAGNIOL-VILLARD bb1f8b4f8b rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:38 +02:00
Jean-Christophe PLAGNIOL-VILLARD 32628c5008 cmd_mac: Move conditional compilation to Makefile
finish remaning CFG_ID_EEPROM in CONFIG_ID_EEPROM
start in commit ad8f8687b7

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:37 +02:00
Heiko Schocher 0b7c563989 muas3001: update BR4 settings
Also set up the port pins for using I2C.

Signed-off-by: Heiko Schocher <hs@denx.de>
2008-09-10 11:20:27 +02:00
Heiko Schocher 245f6ef3e1 muas3001: added support for the LM75 sensor.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-09-10 10:48:04 +02:00
Heiko Schocher 4a02a2dca8 muas3001: activate WDT for the muas3001 board.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-09-10 10:47:44 +02:00
Heiko Schocher a55d074dac muas3001: added 64MB SDRAM autodetection.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-09-10 10:47:24 +02:00
Kumar Gala 9ba2e2c819 Remove support for booting ARTOS images
Pantelis Antoniou stated:
	AFAIK, it is still used but the products using PPC are long gone.
	Nuke it plz (from orbit).

So remove it since it cleans up a usage of env_get_char outside of
the environment code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-09-09 15:52:35 +02:00
Andreas Engel 48d0192fe8 Moved conditional compile into Makefile
Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
2008-09-09 14:42:02 +02:00
Graeme Russ 3ef96ded38 Update i386 code (sc520_cdp)
Attempt to bring i386 / sc520 inline with master

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2008-09-09 11:48:53 +02:00
Anatolij Gustschin e64987a892 85xx: socrates: Enable Lime support.
This patch adds Lime GDC support together with support for the PWM
backlight control through the w83782d chip.  The reset pin of the
latter is attached to GPIO, so we need to reset it in
early_board_init_r.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-09-09 10:14:13 +02:00
Detlev Zundel 3e79b588b5 85xx: Socrates: Major code update.
- Update the local bus ranges in the FDT for Linux for the various
  devices connected to the local bus via chip-select.

- Set the LCRR_DBYP bit in the LCRR for local bus frequencies
  lower than 66 MHz and uses I/O accessor functions consequently.

- UPM data update.

- Update of default environment and configuration.  Use I2C multibus
  as we do have two I2C buses.  Also enable sdram and ext2 commands.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
2008-09-09 10:13:57 +02:00
Timur Tabi e8d18541c6 Update Freescale 85xx boards to sys_eeprom.c
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c.  Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well.  cds_eeprom.c is deleted.

Signed-off-by: Timur Tabi <timur@freescale.com>
2008-09-09 10:13:35 +02:00
Wolfgang Denk fe876787f8 stxxtc: remove empty CONFIG_SHOW_ACTIVITY functions
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-09 10:06:44 +02:00
Wolfgang Denk 965de106ba NETTA2: remove empty CONFIG_SHOW_ACTIVITY functions
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-09 10:03:47 +02:00
Stefan Roese c351575c22 Merge branch 'master' of /home/stefan/git/u-boot/u-boot 2008-09-08 10:35:49 +02:00
Matthias Fuchs ac53ee8318 ppc4xx: Update CPCI405(AB) configuration
This patch add FDT support and command line editing capabilities
for CPCI405 and CPCI405AB boards.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-08 10:28:55 +02:00
Stefan Roese f071f01fd0 ppc4xx: Remove CONFIG_CS8952_PHY define
Since this define is only used on one board that was never really in
production, removing this compile time option doesn't hurt and makes
the code more readable.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-08 10:27:56 +02:00
Jean-Christophe PLAGNIOL-VILLARD ee9536a28c ap325rxa/favr-32-ezkit: Use CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-07 00:42:38 +02:00
Yuri Tikhonov e90fb6afab USB EHCI: reset root hub
Some of multi-function USB controllers (e.g. ISP1562) allow root hub
resetting only via EHCI registers. So, this patch adds the
corresponding kind of reset to OHCI's hc_reset() if the newly
introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates
board).

Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>
2008-09-06 01:24:55 +02:00
Adam Graham f6b6c45840 ppc4xx: Update Kilauea to use PPC4xx DDR autocalibration routines
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-05 12:04:16 +02:00
Ricardo Ribalda Delgado e07f4a8033 ppc44x: Unification of virtex5 pp440 boards
This patch provides an unificated way of handling xilinx v5 ppc440 boards.

It unificates 3 different things:

1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.

If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).

2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)

3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.

In order to support new boards they can be implemented in the next way:

a) Simple Generic Board  (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h  and run make xilinx-ppc440-generic_config
&& make

b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile

c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507

Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:

Cheap board by Avnet for evaluating the Virtex5 FX technology.

This patch adds support for:
 - UartLite
 - 16MB Flash
 - 64MB RAM

Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-05 11:51:22 +02:00
Wolfgang Denk 4615fc22e5 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Conflicts:

	board/esd/dasa_sim/dasa_sim.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-09-03 22:55:55 +02:00
Matthias Fuchs 1092ce218c ppc4xx: Update VOM405 board configuration
- remove PCI code
- add command line editing
- minor cleanup

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03 14:35:08 +02:00
Matthias Fuchs fcaffd597f ppc4xx: Add fdt support for VOM405 boards
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03 14:34:37 +02:00
Matthias Fuchs 9ec367aa2c ppc4xx: Coding style cleanup
Wrap long lines etc.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03 14:32:47 +02:00
Matthias Fuchs 17e65c21ad ppc4xx: Enable USB on PLU405 boards
This patch enables the PCI-OHCI controller on PLU405 board.

Also the default CPU frequency is updated to 266 MHz and
command line editing is enabled.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03 14:32:35 +02:00
Matthias Fuchs 3bc1054cec ppc4xx: Add fdt support for PLU405 boards
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03 14:32:00 +02:00
Matthias Fuchs 5a3e480b78 ppc4xx: Increase U-Boot size to 384kB for PLU405 boards
Signed-off-by: Matthias Fuchs <mf@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-03 14:31:49 +02:00
Andy Fleming 5a8a163ac3 Add pixis_set_sgmii command
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface.  Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports.  This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis.  Either way
requires a reboot.

This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports.  It also allows users
to revert to the current switch settings.

This code does not work on the 8572, as the PIXIS is different.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02 21:18:15 -07:00
Andy Fleming 652f7c2eef Add support for Freescale SGMII Riser Card
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface.  The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02 21:18:15 -07:00
Haavard Skinnemoen ab0df36fc7 avr32: refactor the portmux/gpio code
- Separate the portmux configuration functionality from the GPIO pin
    control API.
  - Separate the controller-specific code from the chip-specific code.
  - Allow "ganged" port configuration (multiple pins at once).
  - Add more flexibility to the "canned" peripheral select functions:
      - Allow using more than 23 address bits, more chip selects, as
	well as NAND- and CF-specific pins.
      - Make the MACB SPEED pin optional, and choose between MII/RMII
	using a parameter instead of an #ifdef.
      - Make it possible to use other MMC slots than slot 0, and support
	different MMC/SDCard data bus widths.
  - Use more reasonable pull-up defaults; floating pins may consume a
    lot of power.
  - Get rid of some custom portmux code from the mimc200 board code. The
    old gpio/portmux API couldn't really handle its requirements, but
    the new one can.
  - Add documentation.

The end result is slightly smaller code for all boards. Which isn't
really the point, but at least it isn't any larger.

This has been verified on ATSTK1002 and ATNGW100. I'd appreciate if
the board maintainers could help me test this on their boards. In
particular, the mimc200 port has lost a lot of code, so I'm hoping Mark
can help me out.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Alex Raimondi <alex.raimondi@miromico.ch>
Cc: Julien May <julien.may@miromico.ch>

Changes since v1:
  * Enable pullup on NWAIT
  * Add missing include to portmux-pio.h
  * Rename CONFIG_PIO2 -> CONFIG_PORTMUX_PIO to match docs
2008-09-01 14:20:41 +02:00
Wolfgang Denk a13b2d9379 Merge branch 'master' of git://git.denx.de/u-boot-arm 2008-09-01 00:06:05 +02:00
Wolfgang Denk e155c9e00b Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2008-09-01 00:04:26 +02:00
Wolfgang Denk de5b094def Merge branch 'master' of git://git.denx.de/u-boot-sh 2008-09-01 00:03:40 +02:00
Wolfgang Denk 845842c1e4 Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2008-08-31 23:53:22 +02:00
Nobuhiro Iwamatsu 6f3d8bb5fa sh: Fix compile error rsk7203 board
This boards used old type preprocessor.
This patch fix compile error.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:08:31 +09:00
Nobuhiro Iwamatsu 1c98172e02 sh: Fix compile error sh7785lcr board
This boards used old type preprocessor.
This patch fix compile error.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:07:33 +09:00
Nobuhiro Iwamatsu 6f0da4972e sh: Renesas Solutions AP325RXA board support
AP325RXA is SH7723's reference board.
This has SCIF, NOR Flash, Ethernet, USB host, LCDC, SD Host, Camera and other.
In this patch, support SCIF, NOR Flash, and Ethernet.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:05:41 +09:00
Nobuhiro Iwamatsu c655fad06b sh: Renesas RSK+ 7203 board support
This adds initial support for the RTE RSK+ SH7203 board.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 23:02:04 +09:00
Nobuhiro Iwamatsu 0d53a47dc0 sh: Renesas R0P7785LC0011RL board support
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.

This patch supports the following functions:
 - 128MB DDR2-SDRAM (29-bit address mode only)
 - NOR Flash
 - USB host
 - Ethernet

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-08-31 22:45:08 +09:00
Jean-Christophe PLAGNIOL-VILLARD f9f692e2b1 smdk6400: Use CONFIG_FLASH_CFI_DRIVER
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-31 00:39:48 +02:00
Guennadi Liakhovetski 7c0e5a8db3 smdk6400: remove redundant bootargs definition
Double bootargs setting leads to a duplicated environmant entry.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31 00:39:47 +02:00
Guennadi Liakhovetski 11edcfe260 ARM: Add support for S3C6400 based SMDK6400 board
SMDK6400 can only boot U-Boot from NAND-flash. This patch adds a nand_spl
driver for it too. The board can also boot from the NOR flash, but due to
hardware limitations it can only address 64KiB on it, which is not enough
for U-Boot. Based on the original sources by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31 00:39:47 +02:00
Stefan Roese 3d4a746e2f ppc4xx: Increase image size for NAND boot target
This is needed since now with HUSH enabled (amcc-common.h) the image
read from NAND exceeds the previous limit.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-30 11:24:44 +02:00
John Rigby 8a490422be ADS5121: Fix NOR and CPLD ALE timing for rev 2 silicon
MPC5121 rev 2 silicon has a new register for controlling how long
CS is asserted after deassertion of ALE in multiplexed mode.

The default is to assert CS together with ALE.  The alternative
is to assert CS (ALEN+1)*LPC_CLK clocks after deassertion of ALE.

The default is wrong for the NOR flash and CPLD on the ADS5121.

This patch turns on the alternative for CS0 (NOR) and CS2 (CPLD)
it does so conditionally based on silicon rev 2.0 or greater.

Signed-off-by: Martha J Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
2008-08-28 13:36:43 -06:00
TsiChung Liew eec567a67e ColdFire: I2C fix for multiple platforms
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-28 09:16:54 -06:00
TsiChung Liew d53cf6a9c7 ColdFire: Add CONFIG_MII_INIT for M5272C3
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-28 09:16:54 -06:00
TsiChung Liew f78ced3028 ColdFire: Multiple fixes for MCF5445x platforms
Add FEC pin set and mii reset in __mii_init(). Change
legacy flash vendor from 2 to AMD LEGACY (0xFFF0),
change cfi_offset to 0, and change CFG_FLASH_CFI to
CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and
M54455EVB env settings in configuration file.

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-28 09:16:54 -06:00
TsiChung Liew 454e725b3a ColdFire: Change the SDRAM BRD2WT timing from 3 to 7
The user manuals recommend 7.

Signed-off-by: Kurt Mahan <kmahan@freescale.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-28 09:16:53 -06:00
TsiChung Liew 79e0799cf6 ColdFire: Raise uart baudrate to 115200 bps
M5249EVB, M5271EVB, M5272C3, M5275EVB and M5282EVB platforms
uart baudrate increase from 19200 to 115200 bps

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-08-28 09:16:53 -06:00
Wolfgang Denk ae9e1b579e Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx 2008-08-28 00:39:27 +02:00
Heiko Schocher 258c37b147 mpc52xx: added support for the MPC5200 based MUC.MC52 board from MAN.
Signed-off-by: Heiko Schocher <hs@denx.de>
2008-08-27 16:03:48 -06:00
Kumar Gala 9490a7f1a9 mpc85xx: Add support for the MPC8536DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:54 -05:00
Kumar Gala 129ba616b3 mpc85xx: Add support for the MPC8572DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:53 -05:00
Kumar Gala 457caecdbc FSL DDR: Remove old SPD support from cpu/mpc85xx
All 85xx boards have been converted to the new code so we can
remove the old SPD DDR setup code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:53 -05:00
Kumar Gala 0e7927db13 FSL DDR: Convert STXSSA to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:53 -05:00
Kumar Gala c360d9b970 FSL DDR: Convert STXGP3 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:52 -05:00
Kumar Gala 8e55313b7a FSL DDR: Convert SBC8560 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:52 -05:00
Kumar Gala 9658bec2e8 FSL DDR: Convert MPC8540EVAL to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:52 -05:00
Kumar Gala 6bfa8f723c FSL DDR: Convert PM856 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:51 -05:00
Kumar Gala d53bd3e17b FSL DDR: Convert PM854 to new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:51 -05:00